Краткое содержание страницы № 1
CARPET HEAT BOND
SEAMING IRON
Model 66738
SET uP AND OPERATING INSTRuCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANuAl.
© ®
Copyright 2009 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual m
Краткое содержание страницы № 2
NOTICE is used to SAVE THIS MANuAl address practices Keep this manual for the safety warn- not related to personal injury. ings and precautions, assembly, operat- CAuTION, without ing, inspection, maintenance and cleaning the safety alert procedures. Write the product’s serial symbol, is used to address number in the back of the manual near the practices not related to assembly diagram (or month and year of personal injury. purchase if product has no number). Keep this manual and
Краткое содержание страницы № 3
an increased risk of electric shock if must be ANSI-approved and breath- your body is grounded. ing protection must be NIOSH-ap- proved for the specific hazards in the c. Do not expose tools to rain or wet work area. conditions. Water entering a tool will increase the risk of electric shock. 4. Tool use and care d. Do not abuse the cord. Never use a. Do not force the tool. use the the cord for carrying, pulling or correct tool for your application. unplugging the tool. Keep cord The
Краткое содержание страницы № 4
ing, contact Harbor Freight Tools for a SAVE THESE replacement. INSTRuCTIONS. 2. Place securely on Iron Holder (6) when not in use. GROuNDING 3. Keep away from flammable objects. TO PREVENT 4. Do not overheat adhesive. ElECTRIC SHOCK AND DEATH FROM 5. When using a handheld tool, maintain INCORRECT GROuNDING a firm, controlling grip on the tool. WIRE CONNECTION: 6. Do not leave the tool unattended Check with a qualified when it is plugged into an electrical electrician if you are
Краткое содержание страницы № 5
grounded outlet. If the tool should 4. When using more than one exten- electrically malfunction or break sion cord to make up the total length, down, grounding provides a low make sure each cord contains at resistance path to carry electricity least the minimum wire size required. away from the user, reducing the risk (See Table A.) of electric shock. (See 3-Prong Plug 5. If you are using one extension cord and Outlet.) for more than one tool, add the 2. The grounding prong in the plug
Краткое содержание страницы № 6
Symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current V~ Amperes A No Load Revolutions per Minute n xxxx/min. 0 (RPM) SKU 66738 For technical questions, please call 1-800-444-3353. Page 6
Краткое содержание страницы № 7
SPECIFICATIONS OPERATING INSTRuCTIONS Read the ENTIRE IMPORTANT Electrical Requirements 120 V~, 800 W SAFETY INFORMATION 112" L, 3-Prong Power Cord Grounded section at the beginning of this manual including all text under Temperature Range 147° - 442° F subheadings therein before set up or use of this product. Temperature Setting Heat Temperature Time to Reach Work Piece and Work Area Set up Setting Range F 1 147° - 190° 2 Minutes 1. Designate a work area that is clean 2 230° - 298° 3
Краткое содержание страницы № 8
reaches the desired temperature. (See Temperature Setting chart.) Consult the adhesive tape manu- facturer’s instruction for proper heat range. 6. Avoid touching the Heat Shield (9) and Bottom Sole Plate (5) while plugged in and hot. 7. Try the Iron on a scrap piece of adhe- sive tape to test for desired tempera- ture result. 8. To prevent accidents, turn off the tool and disconnect its power supply after use. Allow to cool completely, then clean and store the tool indoors out of chil
Краткое содержание страницы № 9
MAINTENANCE AND SERVICING Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOuS INjuRY FROM ACCIDENTAl OPERATION: Turn the Calibration Knob of the tool to its “OFF” position and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. Cleaning and Maintenance 1. BEFORE EACH uSE, inspect the general condition of the tool. Check for loose screws, misalignm
Краткое содержание страницы № 10
Troubleshooting Problem Possible Causes likely Solutions 1. No power at outlet. 1. Check power at outlet. 2. Cord not connected. 2. Check that cord is plugged in. Tool will not heat 3. Heat Control Knob in OFF 3. Turn Heat Control Knob to a heat setting position. position. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. PlEASE READ THE FOllOWING CAREFull Y THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSE
Краткое содержание страницы № 11
ASSEMBl Y DIAGRAM CIRCuIT DIAGRAM SKU 66738 For technical questions, please call 1-800-444-3353. Page 11
Краткое содержание страницы № 12
lIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this prod- uct is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installat
