Краткое содержание страницы № 1
18 GAUGE FINISH ANGLE NAILER
MODEL H5570
INSTRUCTION MANUAL
COPYRIGHT © SEPT, 2003 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN TAIWAN
ONLINE MANUAL DISCLAIMER
THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE
AS IT IS CURRENTLY BEING SHIPPED. THE MACHINE CONFIGURATION CAN CHANGE AS
PRODUCT IMPROVEMENTS ARE INCORPORATED. IF YOU OWN AN EARLIER VER
Краткое содержание страницы № 2
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progres- sion of symbols is described below. Remember that safety messages by them- selves do not eliminate danger and are not a substitute for proper accident pre- vention measures. Indica
Краткое содержание страницы № 3
Safety Instructions For Pneumatic Tools 10. USE PROPER AIR HOSE for the 18. DISCONNECT TOOLS before ser- tool. Make sure your air hose is in vicing and changing accessories. good condition and is long enough to 19. USE THE RECOMMENDED reach your work without stretching. ACCESSORIES. Consult the owner’s manual for recommended 11. WEAR PROPER APPAREL. DO accessories. The use of improper NOT wear loose clothing, gloves, accessories may cause risk of neckties, rings, bracelets, or other injury. jewe
Краткое содержание страницы № 4
Basic Nailer Safety In addition to the rules stated in the previ- ous section, and those in the warning boxes throughout this manual, please observe the following safety tips for your new nailer: 1. READ THIS ENTIRE MANUAL BEFORE OPERATING THE NAIL- ER. 2. ALWAYS DISCONNECT AIR FROM THE NAILER WHENEVER SERVIC- Operating this nailer can propel ING OR INSTALLING NAILS. During objects into the air, causing immedi- maintenance, a nailer connected to ate eye damage. To protect yourself, air may fire
Краткое содержание страницы № 5
INTRODUCTION Most importantly, we stand behind our Commentary tools. If you have any service questions or We are proud to offer the Grizzly Model parts requests, please call or write us at H5570 18 Gauge Finish Angle Nailer. This the location listed below. model is part of a growing Grizzly family of fine power tools. When used according to Grizzly Industrial, Inc. the guidelines set forth in this manual, you 1203 Lycoming Mall Circle can expect years of trouble-free, enjoyable Muncy, PA 17756
Краткое содержание страницы № 6
Compressed Air System Safety Yoke Mechanism The Model H5570 is designed to be oper- A safety yoke mechanism (bump fire) on ated at 70-100 psi. DO NOT exceed the the nose of the nailer acts as a secondary maximum operating pressure for your safety device. When the trigger is pressed, model. the nailer will not fire until the safety yoke mechanism is depressed. Before using your new nailer, install the 1 included ⁄4" NPT male quick connect fitting Before you use your nailer for the first time, 1 o
Краткое содержание страницы № 7
OPERATION Oiling Nailer Loading Nailer When replacing nails in your Model Special oil has been included with your H5570, follow these guidelines: new Grizzly nailer to help maintain its use- ful life. Place one drop of oil in the nailer air Gauge: 18 inlet (as shown in Figure 1) before every 3 Length: ⁄4"-2" use. Wipe off any excess oil near the nail- Capacity: 100 er exhaust to avoid dust build-up. When the oil that was included with the nailer has To load your nailer: been completely used, re
Краткое содержание страницы № 8
3. Before pressing the trigger, make Operating Nailer sure your free hand is positioned out If you have not read the safety instruc- of the way of a potential path of a nail tions in this manual, DO NOT operate in case of deflection. (Deflection is the nailer. caused when grain irregularities, knots or foreign objects inside the Before you operate your nailer, place one wood cause the nail to change its drop of the included oil into the quick con- path, resulting in the nail puncturing nect fitt
Краткое содержание страницы № 9
Clearing Jammed Nails To clear a jammed nail from the dis- charge area on the Model H5570: 1. Disconnect the nailer from the air supply! 2. Pull the spring loaded pusher all the way back and remove the nail stick. 3. Flip up the quick release latch located on top of the nailer nose assembly as shown in Figure 6. 4. Remove the driver guide cover as Always disconnect air from nailer shown in Figure 7. whenever clearing a jammed nail! 5. The jammed nail should now be visi- ble; remove it from the
Краткое содержание страницы № 10
5. The top of the piston should now be Replacing Pistons/O-Rings visible inside the cylinder, which is If you use your nailer day in and day out, housed in the head of the nailer. Grizzly offers repair pistons as cheap 6. Open the magazine. insurance against wasted down time and 7. Watch the discharge area and push lost profits in the event that a piston or pis- the top of the piston with your finger. ton shaft becomes worn out. You will see the piston shaft slide down the discharge area. 8. W
Краткое содержание страницы № 11
H5570 PART BREAKDOWN -10- H5570 18 Gauge Finish Angle Nailer
Краткое содержание страницы № 12
REF PART # DESCRIPTION REF PART # DESCRIPTION 01 PSB113M BTN CAP SCR M5-.8 X 11 40 PSB33M CAP SCREW M5-.8 X 12 02 PH5570002 EXHAUST COVER 41 PH5570041 DRIVER GUIDE 03 PH5570003 SEAL 43 PSB97M CAP SCREW M5-.8 X 6 04 PSB15M CAP SCREW M5-.8 X20 43-1 PLW01M LOCK WASHER 5MM 05 PSS08M SET SCREW M4-.7 X 5 44 PH5570044 PIN 06 PH5570006 CAP 45 PH5570045 MAGAZINE 07 PH5570007 PISTON STOPPER 46 PH5570046 NAIL GUIDE LINER 08 PH5570008 O RING 47 PH5570047 UPPER COVER 09 PH5570009 COLLAR 48 PH5570048 SPIRAL
Краткое содержание страницы № 13
TROUBLESHOOTING CAUSE PROBLEM ACTION Air leaking at trigger valve 1. O-rings in trigger valve 1. O-rings must be replaced area. housing are damaged. & operation of safety yoke must be checked. Air leaking between hous- 1. Loose screws in housing. 1. Tighten screws. ing and hose. 2. Damaged O-ring. 2. Replace O-ring. 3. Loose air fitting. 3. Tighten air fitting. Air leaking between hous- 1. Damaged seal. 1. Replace damaged seals. ing and cap assembly. Tool skips nails while dis- 1. Air leaks. 1.
Краткое содержание страницы № 14
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are here- by limited to
Краткое содержание страницы № 15
WARRANTY CARD Name__________________________________________________________ Street__________________________________________________________ City____________________State________Zip_________ Phone Number____________E-Mail___________________FAX____________ Model #_______________Serial#________________Order #______________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of course, all information is s
Краткое содержание страницы № 16
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE
