Краткое содержание страницы № 1
MODEL G0698
18" X 47" WOOD LATHE
OWNER'S MANUAL
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Краткое содержание страницы № 2
Краткое содержание страницы № 3
Table of Contents SECTION 5: ACCESSORIES ......................... 34 INTRODUCTION ............................................... 2 SECTION 6: MAINTENANCE ......................... 36 SECTION 1: SAFETY ....................................... 6 SECTION 7: SERVICE ................................... 37 SECTION 2: CIRCUIT REQUIREMENTS ........ 9 SECTION 8: WIRING ...................................... 40 SECTION 3: SETUP ....................
Краткое содержание страницы № 4
INTRODUCTION Manual Accuracy Contact Info your machine may not exactly match the manual Machine Description www.grizzly.com
Краткое содержание страницы № 5
Identification Figure 1. A. R. B. C. S. D. T. E. U. F. V. G. W. H. X. I. Y. J. Z. K. L. M. To reduce the risk of N. serious injury when using O. this machine, read and P. understand this entire Q. manual before beginning any operations.
Краткое содержание страницы № 6
Machine Data Sheet MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0698 18" X 47" WOOD LATHE Weight.............................................................................................................................................................. 419 lbs. Length/Width/Height.......................................................................................................80-3/4 x 19-1/16 x 48-1/16 in. Foot Pr
Краткое содержание страницы № 7
Spindle Taper.............................................................................................................................................MT#2 Spindle Size...................................................................................................................... 1-1/4 x 8 (RH) TPI in. Spindle Bore..........................................................................................................................................0.393 in. Spindle Center............
Краткое содержание страницы № 8
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica
Краткое содержание страницы № 9
Safety Instructions for Machinery 7. ONLY ALLOW TRAINED AND PROP- 16. REMOVE CHUCK KEYS OR ADJUSTING ERLY SUPERVISED PERSONNEL TO TOOLS. OPERATE MACHINERY. 17. DAMAGED MACHINERY. 8. KEEP CHILDREN/VISITORS AWAY. 18. DO NOT FORCE MACHINERY. 9. UNATTENDED OPERATION. 19. SECURE WORKPIECE. OFF 10. DO NOT USE IN DANGEROUS 20. DO NOT OVERREACH. ENVIRONMENTS.
Краткое содержание страницы № 10
Additional Safety for Wood Lathes 1. KEEPING GUARDS IN PLACE. 8. OPERATING DAMAGED LATHE. 2. EYE/FACE PROTECTION. 9. WORKPIECE CONDITION. 3. RESPIRATORY PROTECTION. 10. ADJUSTMENTS/MAINTENANCE. 4. MOUNTING WORKPIECE. OFF 5. ADJUSTING TOOL REST. 11. STOPPING LATHE. ON 12. AVOIDING ENTANGLEMENT. 6.
Краткое содержание страницы № 11
SECTION 2: CIRCUIT REQUIREMENTS Power Connection Device 220V Single-Phase Operation Figure 2 Serious personal injury could occur if you connect the machine to power before com- pleting the setup process. DO NOT connect the machine to the power until instructed later in this manual. Electrocution or fire could result if machine is not Figure 2. grounded and installed in compliance with electrical Extension Cords codes. Compliance
Краткое содержание страницы № 12
SECTION 3: SETUP Needed for Setup This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- Description Qty tions before starting the machine! Wear safety glasses dur- ing the entire setup pro- cess! Unpacking The G0698 and its com- ponents are very heavy. Get lifting help or use power lifting equipment such as a fork lift to move please i
Краткое содержание страницы № 13
Inventory Inventory Inventory: (Figures 3–6) Qty A. B. Figure 4. C. D. E. F. G. H. I. J. K. Figure 5. Figure 3. NOTICE Figure 6. Some hardware/fasteners on the inventory list may arrive pre-installed. Check mount- ing locations before assuming that any items from the inventory list are missing.
Краткое содержание страницы № 14
Cleanup Gasoline and petroleum products have low flash points and can explode or cause fire if used to clean machinery. Avoid using these products to clean machinery. Many cleaning solvents are toxic if inhaled. Minimize your risk by only using these products in a well ventilated area. NOTICE Avoid chlorine-based s
Краткое содержание страницы № 15
Site Considerations Weight Load Physical Environment Machine Data Sheet Space Allocation Electrical Installation See below for required space allocation. Lighting Children or untrained people may be seriously injured by this machine. Only install in an access restricted lo
Краткое содержание страницы № 16
3. Assembly Figure 10 To assemble your lathe: 1. Figure 9 Figure 10. 4. Step 7 OPERATIONS Figure 9. Page 18 5. The G0698 and its com- Figure 11 ponents are very heavy. Get lifting help or use power lifting equipment such as a forklift to move heavy items. 2. Note: The headstock end of the lathe is the heaviest and usually requires two people to safely lift i
Краткое содержание страницы № 17
6. 9. Figure 12 Figure Steps 5–6 14 Figure 12. Figure 14. 7. 8. Figure 13 Figure 13.
Краткое содержание страницы № 18
Bolting to Concrete Floors Mounting to Shop Figure 16 Floor Figure 15 Figure 16 NOTICE We strongly recommend securing your machine to the floor if it is hardwired to the power source. Consult with your electrician to ensure compliance with local codes. Figure 15. NOTICE To ensure long life from you lathe and good turning results, make sure the bed is level side-to-si
Краткое содержание страницы № 19
4. Test Run 5. Troubleshooting Page 37 6. 7. Before starting the lathe, make sure you have performed the preceding assembly and adjustment instructions, and you have read through the rest of the manual and are familiar with the various functions and safety features on this machine. Failure to Test
Краткое содержание страницы № 20
SECTION 4: OPERATIONS Basic Controls Damage to your eyes and lungs could result from using this machine without proper pro- Figure 17 tective gear. Always wear a face shield and respirator when operating this machine. OPERATIONS Loose hair and clothing could get caught in the lathe and cause serious personal injury. Keep loose clothing and long hair away from moving Figure 17. Control panel. parts of lathe. A. RPM Digital Readout: NOTICE B. FWD/REV Switch: If
