Краткое содержание страницы № 1
PTO-Driven 6" Wood Chipper
OWNER’S MANUAL
Read carefully and understand RULES FOR SAFE OPERATION and instructions
before operating. Failure to follow the safety rules and other basic safety precautions
may result in serious personal injury.
Item #180100
Краткое содержание страницы № 2
Thank you very much for choosing a NORTHERN TOOL + EQUIPMENT CO., INC., Product! For future reference, please complete the owner’s record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it. This machine is designed for certain applications only. Northern Tool + Equipment strongly recommends this machine is n
Краткое содержание страницы № 3
WORK AREA Keep everyone — especially children — away from the area of operation. Anyone who has not read this manual and received instructions from a qualified person should not be in the area. Provided labels on the unit advise the user of proper hitch dimensions and maximum safe operating speed. Check that proper danger labels are supplied with the drive-line (replacements are available from your drive-line supplier). Provide easy-to-understand instructions for proper drive-line o
Краткое содержание страницы № 4
Never leave the chipper running unattended. Do not attempt alterations, repairs, or adjustments while the chipper head is turning. Always disconnect the PTO and stop the motor. ALWAYS make sure the feed roll drive-shaft and pivots are properly lubricated. ALWAYS make sure the feed roll clutch is properly lubricated and the clutch releases when the handle is pushed toward the chute. ALWAYS make sure the PTO shaft does not come apart or bottom out during the normal lifting range.
Краткое содержание страницы № 5
On drive-lines with torque limiting or overrunning devices, specify that the device be positioned on the end of the drive-line by the implement. For implement connections which require bolts or set screws, select and/or supply hardware which minimizes protrusions. For tractor PTO shaft connections, specify a safety type yoke (twist or slide collar) to minimize protrusions. Provide a proper clearance zone for the operation of the drive-line to avoid damaging the shielding component
Краткое содержание страницы № 6
1. The chipper is a flywheel-and-knife type of chipper, not a shredder. The blades actually chip the limbs as they are fed into the head. The blades must be sharp to operate properly. Dirt, rocks, nails, or other foreign material will shorten blade life. 2. Before operating the chipper, review the machine checklist. After turning the chipper by hand and making sure there are no obstructions in the head, start the tractor and raise the chipper until the PTO shaft is within 15 degrees of stra
Краткое содержание страницы № 7
the lock washers and flat washers. 11. Do not operate the unit without the deflector in place. 12. Before stopping the chipper, be sure the all of the material is out of the head and out of the feed roll. 13. All of the material in the chute must be gone or the unit could jam on a small piece of material. This can usually be cleared by turning the unit backwards by hand. 14. To replace the blades, take the PTO shaft out of gear, then turn off the tractor. The blades on most models are re
Краткое содержание страницы № 8
WARNING: Always stop the PTO, turn off the engine and remove the key before performing any inspection, maintenance, adjustments or cleaning. Lubricate: PTO shaft — 2 zerks on universals once a day with multipurpose grease. Slip Joint — Lubricate with multi-purpose grease. Feed roll pivot — 2 zerks on underside of chute end. Multipurpose grease every 4 to 8 hours of operation. If dust or fine particles make pivot bind, unhook feed roll springs, use cleaning solvent on pivot while mo
Краткое содержание страницы № 9
Symptom Problems Solution Main drive Tighten Head slows but belts are slipping tractor does not Sharpen/reverse Blades dull Blades dull Sharpen/reverse Feed roll clutch Release feed roll clutch and remove kicking in and out Material jammed material by pulling cut of chute, trim of gear excessively in chute forks, and feed into chute Blades dull Sharpen/reverse Sharpen reverse Not chipping Cutter bar not adjusted clean or chip properly-adjust to tolerance level reflector plu
Краткое содержание страницы № 10
PARTS LIST
Краткое содержание страницы № 11
NO. NO. DESCRIPTION DESCRIPTION 1 Bolt 8×18 43 Chipper blade 2 Washer 8 44 Flywheel 3 Washer 8 45 Key C6*20 4 Gearbox mounting plate 46 Main shaft assembly 5 Bolt 6×90 47 Key C10*50 6 Bolt 8×25 48 Little around plate 7 Release hand seat 49 Outer protective cover assembly 8 Nut 6 50 Front supporting plate 9 Nut 8 5l Rear cover 10 Worm reduction gear WPR40 30 1II 52 Bolt 6×12 11 Key 4X 20 53 Bolt M14×1.5×50 12 Screw M6X 20 54 Wash l4 13 Clutch inner claw 55 Nut M14×1.5 14 Clutch o
Краткое содержание страницы № 12
85 Bearing seat shim 90 Washer 12 86 Bearing seat adjust screw 91 Rear plate 87 Drive shaft 92 Driving pulley of W.R.G 88 Nut M10 93 Belt 89 Side plate 94 Driving pulley of W.R.G WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline
