Руководство по эксплуатации Harbor Freight Tools 95091

Руководство по эксплуатации для устройства Harbor Freight Tools 95091

Устройство: Harbor Freight Tools 95091
Категория: Дробилка
Производитель: Harbor Freight Tools
Размер: 3.56 MB
Добавлено: 3/3/2013
Количество страниц: 18
Печатать инструкцию

Скачать

Как пользоваться?

Наша цель - обеспечить Вам самый быстрый доступ к руководству по эксплуатации устройства Harbor Freight Tools 95091. Пользуясь просмотром онлайн Вы можете быстро просмотреть содержание и перейти на страницу, на которой найдете решение своей проблемы с Harbor Freight Tools 95091.

Для Вашего удобства

Если просмотр руководства Harbor Freight Tools 95091 непосредственно на этой странице для Вас неудобен, Вы можете воспользоваться двумя возможными решениями:

  • Полноэкранный просмотр -, Чтобы удобно просматривать инструкцию (без скачивания на компьютер) Вы можете использовать режим полноэкранного просмотра. Чтобы запустить просмотр инструкции Harbor Freight Tools 95091 на полном экране, используйте кнопку Полный экран.
  • Скачивание на компьютер - Вы можете также скачать инструкцию Harbor Freight Tools 95091 на свой компьютер и сохранить ее в своем архиве. Если ты все же не хотите занимать место на своем устройстве, Вы всегда можете скачать ее из ManualsBase.
Harbor Freight Tools 95091 Руководство по эксплуатации - Online PDF
Advertisement
« Page 1 of 18 »
Advertisement
Печатная версия

Многие предпочитают читать документы не на экране, а в печатной версии. Опция распечатки инструкции также предусмотрена и Вы можете воспользоваться ею нажав на ссылку, находящуюся выше - Печатать инструкцию. Вам не обязательно печатать всю инструкцию Harbor Freight Tools 95091 а только некоторые страницы. Берегите бумагу.

Резюме

Ниже Вы найдете заявки которые находятся на очередных страницах инструкции для Harbor Freight Tools 95091. Если Вы хотите быстро просмотреть содержимое страниц, которые находятся на очередных страницах инструкции, Вы воспользоваться ими.

Краткое содержание
Краткое содержание страницы № 1

CHIPPER/SHREDDER
Model 95091
ASSEMBLY AND OPERATING INSTRUCTIONS
Do to continuing improvements, actual product may differ slighlty from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reprodu

Краткое содержание страницы № 2

PRODUCT SPECIFICATIONS Item Description Electrical 120 VAC / 60 Hz / 3400 RPM Requirements Power Switch: Rocker Switch with Safety Key Power Cord: 14 AWG x 3 C (SJT) / 5’3” Long Power Plug: 3-Prong / Grounded Maximum Limb Up to 1-1/4” Diameter Capacity Feed Inlet Size 5-1/2” Long x 1-1/2” Wide Hopper Opening 14-1/2” Long x 10-3/4” Wide Size Wheel Type Solid Rubber with Plastic Hub 6-1/4” Diameter x 1-3/8” Wide Cutter Blade Single Blade Chipper Wheel 3-1/8” Long x 1-3/8” Wide Overal

Краткое содержание страницы № 3

sparks which may ignite the dust or fumes. 3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Provide barriers or shields as needed. Children should never be allowed in the work area. ELECTRICAL SAFETY 4. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adapter plugs. Ch

Краткое содержание страницы № 4

operating power tools may result in serious personal injury. 11. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. 12. Avoid accidental starting. Make sure the Power Switch is off before plugging in. Carrying power tools with your finger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents. 13. Remove

Краткое содержание страницы № 5

the tool serviced before using. Many accidents are caused by poorly maintained tools. 22. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. SERVICE 23. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 24. When servicing a tool, use only identical replacement parts.

Краткое содержание страницы № 6

Chipper/Shredder. Use a stick to push the tree limbs, leaves, etc. into the feed Hopper. 10. Make sure the plastic cover on the Hopper is closed when the machine is running. 11. Always feed large branches slowly into the machine. Branches larger than 1-1/4” diameter should never be fed into the machine. 12. Do not allow processed material to build up in the discharge area. This may prevent proper discharge and can result in kickback of material through the feed Hopper. 13. If the machine beco

Краткое содержание страницы № 7

GROUNDING WARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet instal

Краткое содержание страницы № 8

only wire connected to the tool’s grounding system and must never be attached to an electrically “live” terminal. (See Figure B.) 3. The Chipper/Shredder must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See Figure B.) THIS PRODUCT USES A 3-PRONG PLUG 120 VOLT GROUNDED ELECTRICAL OUTLET FIGURE B EXTENSION CORDS 1. Grounded tools require a three wire

Краткое содержание страницы № 9

Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. Recommended Minimum Wire Gauge For Extension Cords* (120 Volt) * Based on limiting the line voltage drop FIGURE C to five volts at 150% of the rated amperage. SYMBOLOGY FIGURE D UNPACKING When unpacking, check to make sure all the parts shown on the Parts List on page 15 are included. If any parts are m

Краткое содержание страницы № 10

ASSEMBLY INSTRUCTIONS 1. CAUTION! Make sure the Power Switch (42) of the Chipper/Shredder is in its “OFF” position and the unit is unplugged from its electrical outlet prior to performing assembly procedures. To Attach The Wheels: 1. Move the Chipper/Shredder to a clean, dry, level area in which to perform the necessary assembly. 2. Place one Washer (24) on each end of the Axle (25). (See Figure E.) 3. Insert the ends of the Axle (25) through the two Vertical Frames (15). (See Figure E.)

Краткое содержание страницы № 11

Housing (11), making sure to align the two mounting holes in the Chute Cover threaded mounting holes in the Shredder Housing. (7) with the two (See Figure F.) 2. Insert the Hopper (1) into the Chute Cover (7), making sure to align the two mounting holes in the Hopper with the two mounting holes in the Chute Cover (7). (See Figure F.) 3. Place a Washer (3) on two Philip’s Head Screws (8). Then secure the Chute Cover (7) and Hopper (1) to the upper portion of the Shredder Housing (11) with the

Краткое содержание страницы № 12

4. CAUTION! Make sure the Chipper/Shredder is empty of material prior to starting the unit. 5. Check to make sure the Wing Nut (36) is securely tightened. (See Figure G.) 6. Check to make sure the Power Switch (42) is in its “OFF” position. Then plug the Power Cord of the unit into the nearest 120 volt, grounded, electrical outlet. (See Figure G.) 7. NOTE: The Power Switch (42) features a Safety Key to prohibit unauthorized people from turning on the Chipper/Shredder. To use this feat

Краткое содержание страницы № 13

11. Without putting your hands into the Hopper (1), slowly drop the material into the Hopper (one branch at a time). The machine will pull the material in automatically. (See Figure G.) 12. WARNING! Never use your hands to feed material into the Hopper (1). If needed, use a stick to push the branches, leaves, etc. into the Hopper. (See Figure G.) 13. Always stand clear and to the side of the Discharge Chute located at the bottom of the Chipper/Shredder. (See Figure G.) 14. Do not all

Краткое содержание страницы № 14

If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. 3. To clean the unit, use a clean cloth and mild detergent. Do not use solvents. Do not expose the electrical parts of the machine to water or any other liquids. 4. CAUTION! All maintenance, service, or repairs not mentioned in this manual must only be performed by a qualified service technician. TROUBLESHOOTING Problem Possible Cause Solution Motor will not start. 1. No

Краткое содержание страницы № 15

PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/ OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT

Краткое содержание страницы № 16

ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 95091 For technical questions, please call 1-800-444-3353 PAGE 16

Краткое содержание страницы № 17

ELECTRICAL SCHEMATIC SKU 95091 For technical questions, please call 1-800-444-3353 PAGE 17

Краткое содержание страницы № 18

IMPORTANT WARRANTY INFORMATION LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal


Скачавание инструкции
# Руководство по эксплуатации Категория Скачать
1 Harbor Freight Tools 92281 Руководство по эксплуатации Дробилка 0
2 Harbor Freight Tools 95964 Руководство по эксплуатации Дробилка 8
3 Philips SVGA COLOUR MONITOR 7CM5209 Руководство по эксплуатации Дробилка 0
4 Agri-Fab Chip-N-Vac 2468 Руководство по эксплуатации Дробилка 1
5 Philips SVGA COLOUR MONITOR 7CM5279 Руководство по эксплуатации Дробилка 2
6 Agri-Fab Chip-N-Vac 552493 Руководство по эксплуатации Дробилка 0
7 Agri-Fab Chip-N-Vac 502493 Руководство по эксплуатации Дробилка 1
8 Agri-Fab Chip-N-Vac 45-0253 Руководство по эксплуатации Дробилка 0
9 Ashly CLX-52 Руководство по эксплуатации Дробилка 16
10 Bolens 460 Series Руководство по эксплуатации Дробилка 0
11 Ativa CS2171 Руководство по эксплуатации Дробилка 0
12 Ativa CS 2165 Руководство по эксплуатации Дробилка 0
13 Billy Goat TKD505SPT Руководство по эксплуатации Дробилка 1
14 Billy Goat TKD501H Руководство по эксплуатации Дробилка 1
15 Billy Goat KD510 Руководство по эксплуатации Дробилка 1