Краткое содержание страницы № 1
16” ELECTRIC Chain Saw
WITH BRAKE
Model 02810
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
© ®
Copyright 2002 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
Краткое содержание страницы № 2
PRODUCT SPECIFICATIONS Item Description Electrical Requirements 2 HP / 120 V / 60 Hz / 13.2 Peak Amps, 7.8 No Load Amps / 1600 Watt Cutter Bar Size 16” Brake Stop Electromagnetic Stop Within .15 Sec. After Shutoff ® Chain Type #91VG “Oregon Chain” Oiler System Automatic Chain Guide Rail 16-1/8” Long x 2-1/2” Wide x 5/32” Thick Dimensions Weight 11 Pounds SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance an
Краткое содержание страницы № 3
6. DRESS SAFELY. Do not wear loose clothing or jewelry, as they can become caught in moving parts. Wear a protective hair covering to prevent long hair from becoming caught in moving parts. Wear close fitting clothing and steel toed shoes. 7. DO NOT OVERREACH. Keep proper footing and balance at all times to prevent tripping, falling, back injury, etcetera. 8. INDUSTRIAL APPLICATIONS MUST FOLLOW OSHA REQUIREMENTS. 9. STAY ALERT. Watch what you are doing at all times. Use common sense. Do not
Краткое содержание страницы № 4
SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS 1. MAINTAIN A SAFE WORKING ENVIRONMENT. Make sure the work area is well lit. Make sure there is adequate surrounding workspace. Always keep the work area free of obstructions, tree limbs, vegetation, and other debris. Do not use the Chain Saw in areas near flammable chemicals, dusts, and vapors. Do not use the Chain Saw in a damp or wet location. 2. DO NOT USE THE CHAIN SAW WITH ADULTS, CHILDREN, AND PETS IN CLOSE PROXIMITY. 3. ALWAYS HOLD THE CHAIN
Краткое содержание страницы № 5
11. IF AN EXTENSION CORD (not included) IS USED, MAKE SURE TO USE ONLY UL APPROVED, OUTDOOR, CORDS HAVING THE CORRECT GAUGE AND LENGTH. (See Figure A.) REQUIRED MINIMUM EXTENSION CORD GAUGE – 120 VOLT NAMEPLATE EXTENSION CORD LENGTH AMPERES (At Full Load) 0 - 25 25 - 50 50 -100 100 – 150 150– 200 Feet Feet Feet Feet Feet 0 - 5 16 16 16 12 12 5.1 - 8 16 16 14 10 - 8.1 - 12 14 14 12 - - 12.1 - 15 12 12 10 - - 15.1 - 20 10 10 10 - - FIGURE A 12. REDUCE THE RISK OF ACCIDENTAL STARTING. Make sure th
Краткое содержание страницы № 6
any doubt about the safety issues involved, have a qualified, certified, arborist/tree surgeon do the work for you. 21. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contain chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and ce- ment or other masonry products, arsenic and chromium
Краткое содержание страницы № 7
FIGURE B 5. Replace the Chain Cover (46), and tighten the Nylon Insert Nut (67) so that the Cover is snug, but not tight. (See Figure D, next page.) 6. Pull gently up on the tip of the Guide Bar (52), while turning the Blade Adjustment Screw (61) clockwise (photo 005.) Because the saw is light in weight, this is easier if someone holds the handle. Do not overtighten the Chain. There should only be 1 about / ” of space when the Chain is pulled upward at the center of the Guide Bar. 4 Lightly oil
Краткое содержание страницы № 8
BLADE ADJUSTMENT SCREW (61) OIL FILL CAP (11) ON/OFF TRIGGER (25b) CHAIN (57) NUT GUIDE BAR (52) CHAIN COVER (67) FIGURE D (46) To Check For Proper Chain Tension: 1. The Chain (57) tension is proper when the Chain snaps back after being pulled 1/4” away from the Guide Bar (52) with light force. There should be no sagging between the Chain and Guide Bar underneath. When necessary, use a screwdriver to turn the Adjustment Screw (61) clockwise to tighten, or counterclockwise to loosen, the Chain
Краткое содержание страницы № 9
OPERATING INSTRUCTIONS The Safety Brake: 1. The Safety Brake is activated when the back of the operator’s hand pushes against the back of the Protect Plate (17). When activated, the Chain Saw will stop auto- matically, and the On/Off Trigger (25b) should be manually released. Next, pull the Protect Plate (17) back to its initial position in order to restart the Chain Saw. NOTE: If the Protect Plate (17) is not pulled back to its initial position, the Chain Saw will not operate. (See Figure E
Краткое содержание страницы № 10
INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING: Always turn the On/Off Trigger (25b) to its “OFF” position and unplug the Electric Cord (23) from its electrical outlet before performing any inspection, mainte- nance, or cleaning. (See Figure E.) 2. BEFORE EACH USE, inspect the general condition of the Chain Saw. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts (i.e., Chain, 57), damaged electrical wiring, and any other condition that may affect its saf
Краткое содержание страницы № 11
PARTS LIST Pn artDy escriptio Qt 'tPn arDy escriptio Q't 1gM1 otor housin 3e2B1 rake plat 2rR1 ear cove 3k3B1 rake bloc 38 aS0 crew ST4.2*1 143tB1 rake bel 3r bF1 lat washe 153rP1 inion gea 4hC1 arbon brus 3d6C1 onnection ro 5rC1 arbon brush holde 3l7T1 ermina 6gC1 arbon brush housin 3g8T1 orsion sprin 70S5 crew ST5*2 3h9S2 witc 86S4 crew ST3*1 480B1 earing 60 90S2 crew ST5*3 4r1B1 ig gea 1r 0S1 tato 4r2F1 ront cove 1e 1O1 il bottl 453S1 crew M6*3 1e 3O1 il pip 464N1 ut M 11 4aO1 il pump 4r5C1 h
Краткое содержание страницы № 12
ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. REV 05/05 SKU 02810 For technical questions, please call 1-800-444-3353. Page 12
