Краткое содержание страницы № 1
Installation Manual
Volvo C30 T5 Front Mount
Intercooler System
Краткое содержание страницы № 2
Volvo C30 T5 Intercooler System / Installation Manual i C Contents Important Information i Parts List i Required Tools and Materials 1 1.0 - Vehicle Preparation 1 2.0 - Removing and Trimming Front Fascia (Nose Section) 2 3.0 - Removing Factory Intercoolers and Tubes 3 4.0 - Installing New Intercooler 4 5.0 - Start Engine and Check Connections 6 6.0 - Trim and Install Front Fascia (Nose Section) 7 7.0 - Test Drive 8 ! Important Information Congratulations on your purchase of the Bell Intercoole
Краткое содержание страницы № 3
Volvo C30 T5 Intercooler System / Installation Manual 1 Required Tools and Materials To efficiently complete the installation of your intercooler you will need the following tools and materials, in addition to those parts supplied with your intercooler. Tools • 1/4” Drive Ratchet • T20 and T30 Torx Bits and Suitable Driver • 1/4” Drive Extensions - 3” Length • Small Flat-head Screwdriver • 3/8” Drive Ratchet • Phillips Screwdriver • 3/8” Drive Extension - 3” Length • Hacksaw or Cutting Wh
Краткое содержание страницы № 4
Volvo C30 T5 Intercooler System / Installation Manual 2 Removing Front Fascia (Nose Section) 2.0 The first step in the installation will involve removal of the front fascia Front Fascia (front nose section) of the vehicle (see Fig. 2.1). The front fascia of (upper section) the C30 is comprised of two pieces, an upper section and a lower section, as shown in Figure 2.1. These two sections remaining joined during the installation process and will not be separated. Attached to the front fascia
Краткое содержание страницы № 5
Volvo C30 T5 Intercooler System / Installation Manual 3 • Carefully remove the five (5) plastic rivets securing the front fascia to the upper radiator bulkhead (see Fig. 2.4). Please note, these Upper Radiator Bulkhead rivets are designed to be reused. Using a Phillips screwdriver press the center section of the rivet down approximately 1/8”, until you feel a click, when the rivet has released. Once released, you may extract the rivet from the hole. Repeat for all rivets. • The lower sectio
Краткое содержание страницы № 6
Volvo C30 T5 Intercooler System / Installation Manual 4 • Loosen hose clamp securing intercooler outlet hose to intercooler and disconnect hose from intercooler. Mounting 3.3 Remove Hose Clamps Bolt The factory hose clamps will be replaced with high-strength T-bolt hose clamps for use with your new intercooler. You will need to re- move the factory hose clamps prior to installing the new intercooler. • Carefully remove factory hose clamps from intercooler inlet and outlet hoses. These clamps
Краткое содержание страницы № 7
Volvo C30 T5 Intercooler System / Installation Manual 5 the on the factory intercooler. Refer to Figure 4.1 to ensure proper orientation of the sensor relative to the intercooler. • Apply a thin coating of motor oil to the IAT sensor o-ring. • Carefully insert sensor into new intercooler. Position as shown in Figure 4.1. • Install M5- 0.8 x 20mm bolt and M5 washer (supplied with inter- cooler kit) to secure fastener. Tighten fastener. 4.2 Install T-Bolt Hose Clamps IAT The T-Bolt hose cl
Краткое содержание страницы № 8
Volvo C30 T5 Intercooler System / Installation Manual 6 4.6 Recheck All Fasteners, Hose Clamps and Connections Before proceeding, recheck all hose clamps for proper installation and clearance. Also recheck intercooler position (as per step 4.3) and all mounting fasteners. Recheck IAT sensor harness to be sure it is properly connected. Intercooler Intercooler Mounting Intercooler Mounting Point To Radiator Point Gap Left-Side Mounting Point Figure 4.5 Right-Side Mounting Point Figure 4.4 Figure
Краткое содержание страницы № 9
Volvo C30 T5 Intercooler System / Installation Manual 7 Trim and Install Front Fascia (Nose Section) 6.0 This step requires relatively easy trimming of the plastic and urethane components of the front fascia. All trimming can be easily accomplished with a hacksaw or cutting wheel and cleaned up with a file and sand paper. 6.1 Remove Lower Grill Insert The plastic grill insert in the lower grill opening is secured by nine plastic tabs. Carefully release tabs and remove grill insert. 6.2 Mark an
Краткое содержание страницы № 10
Volvo C30 T5 Intercooler System / Installation Manual 8 • Draw lines on side surfaces connecting upper and lower corners (see Fig. 6.1). • Using hacksaw or cutting wheel, care- fully cut along lines. • Carefully clean up cut edges with file and/or sandpaper. 6.4 Reinstall Front Fascia Reinstall front fascia in reverse sequence of removal process (see Step 2.0, pg 2). • Position front fascia in front of car and connect driving light wiring connectors (if so equipped). • Lift fascia and g
