Краткое содержание страницы № 1
SHIELD UP - 8 TO 18 FT. SPREAD WIDTH
SHIELD DOWN - 3 TO 4 FT. SPREAD WIDTH
OWNERS
MANUAL
Model No.
45-02101-101
PRO 125#
BROADCAST SPREADER
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
Assembly
Operation
Maintenance
Repair Parts
PRINTED IN U.S.A. FORM NO. 47438 (Rev. 2/00)
Краткое содержание страницы № 2
TABLE OF CONTENTS SAFETY RULES...............................................................2 MAINTENANCE & STORAGE............................................9 CARTON CONTENTS......................................................2 LUBRICATION..................................................................9 ASSEMBLY ......................................................................4 PARTS EXPLOSION.......................................................10 OPERATION ........................
Краткое содержание страницы № 3
FULL SIZE HARDWARE REFERENCE CHART J C A B D E K M L I H F G NOT SHOWN FULL SIZE O N U P Q R S T V REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION L 1 Spacer Tube, Short (1") A 3 Bolt, Carriage 1/4" x 3/4" M1 Spacer Tube, Long (1-5/16") B 2 Bolt, Hex 1/4" x 5/8" N 4 Bracket, Swivel C 6 Bolt, Hex 1/4" x 3/4" O 1 Link, Flow Control D 2 Bolt, Hex 1/4" x 1-1/2" P 2 Bracket, Angle Stop E 6 Bolt, Hex 1/4" x 1-3/4" Q 1 Spring, Extension F 16 Nut, Hex Lock 1/4-20 R 1 Knob, Hand G 17 Washer, 5/16" S
Краткое содержание страницы № 4
5. Place the short spacer tube and a 3/4" washer onto the ASSEMBLY INSTRUCTIONS end of the axle that has the large drilled hole (left hand side). See figure 2. TOOLS REQUIRED FOR ASSEMBLY 6. Place the drive wheel onto the axle. The notched hub (1) Pliers and the air valve should face to the outside. See figure (2) 7/16" Open End or Box Wrenches 2. (2) 9/16" Open End or Box Wrenches 7. Fasten the wheel to the axle using a 1/4" x 1-3/4" hex bolt and a 1/4" hex lock nut. See figure 2. REMOVAL OF P
Краткое содержание страницы № 5
10. Assemble the (long) handle tube to the side of the 14. Assemble the leg stand tube to the handle tube (long) crossover tube opposite the shaft support plate, as using two 1/4" x 1-1/2" hex bolts and two 1/4" hex lock shown in figure 4. Fasten the handle tube to the middle nuts. Tighten. See figure 5. hole using the bolt, flat washer and hex lock nut which you removed in step 9. Do not tighten yet. 15. Place the vinyl cap on the leg stand tube. See figure 5. IMPORTANT: DO NOT assemble the
Краткое содержание страницы № 6
18. Assemble the flow control arm to the flow control mount- 21. Hook the free end of the flow control rod through the hole ing bracket using one 1/4" x 5/8" hex bolt and one 1/4" in the slide gate bracket located near the bottom of the hex lock nut. Do not over tighten. The flow control arm hopper. See figure 9. must pivot freely. See figure 7. SLIDE 19. Hook one end of the spring through the hole at the bend GATE in the flow control rod. Hook the other end in the hole in BRACKET HOPPER the fl
Краткое содержание страницы № 7
24. Assemble the flow control gauge onto the flow control 28. Assemble the spreader shield to the front swivel brack- mounting bracket using a 1/4" x 3/4" carriage bolt, a ets using two 1/4" x 3/4" carriage bolts, 5/16" washers nylon washer and the hand knob. See figure 11. and the two 1/4" plastic knobs. See figure 13. 25. Push the flow control arm forward to the off position and 29. Assemble the spreader shield to the rear swivel brackets slide flow control mounting bracket toward hopper until
Краткое содержание страницы № 8
OFF-ON 0 1 2 3 4 5 6 7 8 9 10 USING THE SPREADER OPERATION 1. Determine approximate square footage of area to be covered and estimate amount of fertilizer or seed re- STARTING THE SPREADER quired. 1. Pull the flow control arm back against the flow control 2. With flow control arm in off position, set flow rate gauge gauge for the "ON" position. This opens the closure plate at number indicated in flow rate chart for light or heavy in the bottom of the hopper and starts the material flow. applicat
Краткое содержание страницы № 9
IMPORTANT: Application rates (shown on chart) are LUBRICATION affected by humidity and mixture content of material (granu- 1. Apply a little automotive grease to the sprocket and gear. lar and pellet). Minor adjustment of the flow rate setting may 2. Oil nylon bushings on sprocket shaft. See figure 17. be necessary to compensate for these variables. The rate 3. Oil axle/shaft bushing on axle as shown in figure 17. chart is calculated for light and heavy application. The faster 4. Oil right hand
Краткое содержание страницы № 10
REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-02101-101 68 39 64 61 E F 65 67 64 63 48 9 64 44 59 52 39 55 64 61 14 41 17 55 38 8 9 70 42 64 37 45 1 9 38 37 71 63 37 64 29 40 A 72 40 64 9 60 9 31 5 9 B 39 7 30 34 2 47 53 54 61 3 6 26 9 57 46 4 25 49 33 62 37 58 37 27 10 A 9 36 64 11 66 35 32 C 56 E D 53 37 19 F 9 20 9 22 69 64 37 19 D 12 13 9 50 18 51 4 21 21 C 43 51 9 B 23 28 51 35 24 23 16 15 9 9 10
Краткое содержание страницы № 11
REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-02101-101 REF. PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION NO. NO. NO. NO. 1 44466 1 Hopper 37 1509-069 12 Bolt, Hex 1/4-20 x 1-3/4" Lg. * 2 43882 4 Rivet, Stainless 38 43866 2 Bolt, Hex 1/4-20 x 5/8" Lg. Gr. 5* 3 62482 1 Ass'y, Guide Closure 39 1543-069 11 Washer, Nylon 4 44462 1 Tube, Frame 40 43088 9 Washer, Flat 1/4" Std. 5 23753 1 Slide Gate Angle Bracket 41 23755 1 Gage, Flow Control 6 23758 1 Slide Gate Bracket 42 23754 1 Bracket, Flow Con
Краткое содержание страницы № 12
REPAIR PARTS 303 West Raymond Sullivan, IL. 61951 (217) 728-8388 / www.agri-fab.com
