Руководство по эксплуатации Razor 20036560

Краткое содержание страницы № 1

™
Flash RideR 360°
Owner’s Manu
Read and understand this entire manual before riding!
DO NOT RETURN TO STORE!
NOTE: Manual illustrations are for demonstration purposes only. Illustrations
may not reflect exact appearance of actual product. Specifications subject to
change without notice.
Item Number:
v.1_10-11 20036560
al

Краткое содержание страницы № 2

CONTENTS Safety Warnings ............................................................ 1 Parts Breakdown ........................................................... 6 Before You Begin ........................................................... 2 Safety Reminders .......................................................... 7 Assembly and Set-Up ................................................. 3-4 Warranty ........................................................................ 7 Set-Up and Usage

Краткое содержание страницы № 3

BEfORE yOU BEGIN Remove contents from box and check parts against parts diagram found on page 6. Remove the foam separators that protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint or WARNING: DO dents that may have occurred during shipping. Because the Flash Rider 360˚ was partially assembled and packed at the NOT USE NON-RAZOR factory there should not be any problems, even if the box has a few scars or dents. PRODUCTS WITH Y

Краткое содержание страницы № 4

ASSEMBLy AND SET-UP q Attaching the front fork Required Tools: 13mm open wrench and 5mm Allen wrench WARNING: Failing to properly tighten the steering bolt that attaches the front fork assembly to the frame assembly, can cause you to lose control and fall. 1 Remove the steering bolt and 2 Insert the front fork into the 3 Be sure to properly align slot in locknut from the frame assembly frame assembly. headset tube with pin on fork as with a 13mm open wrench and shown. 5mm Allen

Краткое содержание страницы № 5

ASSEMBLy AND SET-UP q Attaching the Rear Caster Wheels Required Tools: 5mm Allen wrench 1 Insert the caster bolt into the 2 Using a 5mm Allen wrench, 3 If you’re having trouble thread- frame. If aligned correctly, the caster tighten the hex bolt located on the ing the caster into frame, use a rag thread should go half way into the underside of the wheel cover until or small brush with a little WD- frame with no resistance. the caster bolt is all the way inside 40® to remove any excess parti

Краткое содержание страницы № 6

SET UP AND USAGE INSTRUCTIONS q Replacing the Spark Cartridge: Friction during sparking will eventually wear out the replaceable cartridge and cause the scooter to stop making sparks. Worn out cartridges must be replaced. WARNING: Do not attempt to replace cartridge immediately after riding as cartridge will be hot. Handle only when cool. WARNING: Keep fingers clear of Spark Bar hinge. 1 Using your thumbs, press tabs 2 Place a new cartridge in back of the bracket making su

Краткое содержание страницы № 7

fLASH RIDER 360˚ CASTER TRIkE PARTS Keep your Flash Rider 360˚ rolling for years with genuine Razor parts. Visit our website to purchase replacement parts. (Specifications subject to change without notice.) 1 Handlebar Grip (x2) 6 Rear Wheel Assembly (x2) 2 Front Fork 7 Seat 2-1 Front Fork Coupling Bolts (x4) 8 Spark Handle 3 Front Cover 9 Spark Bar 4 Steering Bolt 10 Spark Cartridge 4-1 Lock Nut 11 Spark Cartridge Cover 5 Front Wheel w/ Pedals and Cranks Complete 6

Краткое содержание страницы № 8

SAfETy REMINDERS PRE-RIDE CHECkLIST Loose Parts Tire Care Check and secure all fasteners before every ride. Make sure Periodically inspect the wheels for excess wear. q q the steering bolt and casters are tight. There should not be any unusual rattles or sounds from loose parts or broken components. If you are not sure, ask an experienced mechanic to check. frame, fork and Handlebars Safety Gear Check for cracks or broken connections. Although broken frames Always wear proper protective equi