Краткое содержание страницы № 1
Bev Center Cover 8/4/04 1:37 PM Page 1
ICE-MAKERS,
COMBOS,
P.O. Box 245040
REFRIGERATORS,
Milwaukee, WI 53224-9540
Phone 414.354.0300
FAX 414.354.7905
75 BEV BEVERAGE
www.U-Line.com
CENTER
Printed in U.S.A.
R R
P/N 30035
R
User’s Manual
User’s Manual
Краткое содержание страницы № 2
Bev Center Cover 8/4/04 1:37 PM Page 2 U-LINE CORPORATION LIMITED WARRANTY U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from defects in materials and workmanship for a period of five years from the d
Краткое содержание страницы № 3
30035 User Manual Body.qxd 1/5/05 8:08 AM Page 1 INTRODUCTION Congratulations on your purchase of your U-Line product. A pioneer in the field for more than 40 years, U-Line is the world’s number one man- ufacturer of built-in, under-counter ice making and specialty refrigera- tion products. U-Line dedicates 100% of its research and development to these products. The result: U-Line technology leads the market with innovation, design, depth of product line and performance. U-Line also backs cu
Краткое содержание страницы № 4
30035 User Manual Body.qxd 1/5/05 8:08 AM Page 2 User’s Manual PLEASE RECORD YOUR MODEL’S INFORMATION Whenever you call to request information or service, you will need to know your model number and serial number. You can find this infor- mation on the serial plate located on the inside wall of your unit and on the product registration card. PRODUCT REGISTRATION CARD The package containing this manual also includes your product regis- tration information. Warranty coverage begins at the time
Краткое содержание страницы № 5
30035 User Manual Body.qxd 1/5/05 8:08 AM Page 3 TABLE OF CONTENTS INTRODUCTION..........................................................................1 SAFETY PRECAUTIONS ...............................................................4 INSTALLATION ...........................................................................7 LEVELING THE UNIT .................................................................10 CONNECTING THE WATER SUPPLY – ICE MAKER MODELS ONLY ..12 GRILLE INSTALLATION ...
Краткое содержание страницы № 6
30035 User Manual Body.qxd 1/5/05 8:08 AM Page 4 User’s Manual SAFETY PRECAUTIONS Do not attempt to install or operate your unit until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a Danger, Warning or Caution based on the risk type. DEFINITIONS This is the safety alert symbol. It is used to alert you to ! potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER ! !
Краткое содержание страницы № 7
30035 User Manual Body.qxd 1/5/05 8:08 AM Page 5 GENERAL PRECAUTIONS DANGER ! ! Risk of child entrapment. Before you throw away your old refrigerator or freezer, take off the doors and leave shelves in place so that children may not easily climb inside. WARNING ! • Never attempt to repair or perform maintenance on the unit until the electricity has been disconnected. • Altering, cutting of power cord, removal of power cord, removal of power plug, or direct wiring can cause serious injury, fir
Краткое содержание страницы № 8
30035 User Manual Body.qxd 1/5/05 8:08 AM Page 6 User’s Manual GENERAL PRECAUTIONS (CONTINUED) CAUTION • Using a heater to speed up defrosting can damage the inner lining. DO NOT use any type of electrical heater to defrost. • Use only genuine U-Line replacement parts. Imitation parts can reduce ice rate, cause water to overflow from ice maker mold, damage the unit, and may void the warranty. 6
Краткое содержание страницы № 9
30035 User Manual Body.qxd 1/5/05 8:08 AM Page 7 INSTALLATION SITE PREPARATION Your U-Line product is designed to be installed in a wall or under a counter or freestanding. NOTE The 75 BEV must be ordered for right or left hand door. The 75 BEV doors are not reversible. Any reference to revers- ing the door, does not apply to the 75 BEV. 1. Position the unit on a flat, level surface, capable of supporting the entire weight of the unit. Remember the unit will be significantly heavier once it i
Краткое содержание страницы № 10
30035 User Manual Body.qxd 1/5/05 8:08 AM Page 8 User’s Manual DANGER ! ! ELECTROCUTION HAZARD! Electrical Grounding Required. This appliance is equipped with a three prong (grounding) polarized plug for your protection against pos- sible shock hazards. It must be plugged into a properly grounded three-prong receptacle. • NEVER remove the round grounding prong from the plug. • NEVER use a two-prong grounding adapter. • NEVER use an extension cord to connect power to the unit. Where a two-pron
Краткое содержание страницы № 11
30035 User Manual Body.qxd 1/5/05 1:58 PM Page 9 NOTE Keep in mind that the door of the unit may be mounted on either side of the cabinet (see REVERSING THE DOOR) except for the 75 BEV. All U-Line units have a zero clear- ance for the door to open when the hinge is on the right, except for Stainless Steel Doors. Additional clearance is needed for the Combo Models 29A, 29FF, and 75A only when the door hinge is on the left. See built-in installation for additional clearance requirements for the
Краткое содержание страницы № 12
30035 User Manual Body.qxd 1/5/05 1:58 PM Page 10 User’s Manual LEVELING THE UNIT It is important that these units, primarily the ice maker assembly and 75 BEV are level. All 75 and 15 Series units are equipped with adjustable feet for leveling and height adjustment (Figure 3). All other units have rubber feet. To level units with adjustable feet: 1. Adjust all four leveling feet evenly so that the top of the cabinet is at the desired installation height and level. 2. Using a level of at leas
Краткое содержание страницы № 13
30035 User Manual Body.qxd 1/5/05 1:58 PM Page 11 4. Place the unit in position where it is to be installed. Re-check cabinet height and levelness (Figure 4) and adjust if necessary. TURN FOOT TO ADJUST UL105 Figure 3 LEVEL TWO PLACES UL135 Figure 4 11
Краткое содержание страницы № 14
30035 User Manual Body.qxd 1/5/05 8:08 AM Page 12 User’s Manual CONNECTING THE WATER SUPPLY - ICE MAKER MODELS ONLY Install a 1/4" outside diameter copper water line (not supplied with unit) from the nearest COLD water pipe. When connecting the water supply, follow these guidelines: • Review the local plumbing codes before you install the unit. • In most instances, the cold water supply will come from the basement through a hole in the floor. • The water pressure should be between 15 and 1
Краткое содержание страницы № 15
30035 User Manual Body.qxd 1/5/05 8:08 AM Page 13 1. Locate the compression fitting and ferrule packed in the unit. Slide the compression fitting and ferrule over the 1/4" outside diameter water supply line. Do not use thread sealing com- pound or tape. Using two wrenches, tighten the compres- sion fitting on the supply line (see Figure 6). Do not overtighten. UL134_CO Figure 6 2. Carefully bend the water supply line into position and connect the line to the solenoid valve WATER (see Figure 7
Краткое содержание страницы № 16
30035 User Manual Body.qxd 1/5/05 8:08 AM Page 14 User’s Manual WATER LINE UL104 Figure 9 NOTE On BI-95 and BI-98 models, route the water supply line through the unit so it does not come into contact with any internal components other than the solenoid valve (Figure 9). Normal operation creates some vibration. A water supply line contacting an internal component or cabinet wall can cause excessive noise during operation or damage to the line. CAUTION If you are not intending to use the ice
Краткое содержание страницы № 17
30035 User Manual Body.qxd 1/5/05 8:08 AM Page 15 NOTE After completing the installation, turn on the water and recheck water connection for leaks. Apply additional tight- ening if needed. Do not use thread sealing compound or tape. 4. Plug in the power cord. 5. Gently push the unit into position. GRILLE INSTALLATION 1. With a standard blade screwdriver (or 1/4” nutdriver), remove the grille screw to attach the grille (Figure 11). GRILLE SCREW UL106 Figure 11 2. Remove the control knob by pu
Краткое содержание страницы № 18
30035 User Manual Body.qxd 1/5/05 8:08 AM Page 16 User’s Manual 4. Place the two hook-hinges (located on the rear bottom side of the grille) on the front lip of the unit base. Swing the grille up into posi- tion, aligning the grille and cabinet screw hole (Figure 12). UL107 Figure 12 5. Insert the screw. Do not to overtighten. 6. Reinstall control knob. 16
Краткое содержание страницы № 19
30035 User Manual Body.qxd 1/5/05 8:08 AM Page 17 95 AND 98 MODELS 1. With a standard blade screwdriver (or 1/4" nutdriver), remove the screw needed to attach the grille (see Figure 13). 2. Carefully remove the grille from inside the unit. Locate the screw hole at the top, middle recessed section of the grille. 3. Place the two hook-hinges (located on the rear bottom side of the grille) on the front lip of the unit base. Swing the grille up into position, aligning the grille and cabinet scr
Краткое содержание страницы № 20
30035 User Manual Body.qxd 1/5/05 8:08 AM Page 18 User’s Manual GLASS SHELF INSTALLATION (for models with Glass Shelves) 1. Carefully remove the glass shelves from the packaging. UL108a 75 BEV Figure 15 2. Slide the shelves onto lower two sets of ribs, making sure the sil- ver edge strip is toward the front of the unit and the decorative graphics are on the underside of the shelves. Make sure the shelves are inserted fully into the unit (Figure 15). The white edge strip toward the rear preven
