Краткое содержание страницы № 1
Programming
Washer-Extractor
Pocket Hardmount
UniLinc Control
Refer to Page 10 for Model Identification
PHM1401C
PHM1401C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. F8138801R3
www.comlaundry.com September 2009
Краткое содержание страницы № 2
Краткое содержание страницы № 3
Safety Information.............................................................................. 4 Table of Explanation of Safety Messages........................................................... 4 Important Safety Instructions ............................................................... 4 Contents Safety Decals ........................................................................................ 6 Operator Safety..........................................................................
Краткое содержание страницы № 4
Run Diagnostic Menu........................................................................... 23 Speed, Temp and Water Level Menu ................................................... 24 Cycle Aborted Retry Menu................................................................... 24 Cycle Aborted Fatal Menu.................................................................... 25 Cycle Stopped Menu............................................................................. 25 Delayed Start Menu .....
Краткое содержание страницы № 5
Rapid Advance Menu ........................................................................... 44 Shakeout Menu ..................................................................................... 45 Banners Menu....................................................................................... 45 Factory Defaults Menu ......................................................................... 45 Water Level Confirmation Menu.......................................................... 46 Water
Краткое содержание страницы № 6
Safety Information Explanation of Safety Messages Important Safety Instructions Precautionary statements (“DANGER,” “WARNING,” WARNING and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These To reduce the risk of fire, electric shock, precautions are intended for the personal safety of the serious injury or death to persons when operator, user, servicer, and those maintaining the using your washer, follow these basic machine. precautions:
Краткое содержание страницы № 7
Safety Information 9. Do not install or store the washer where it will be 20. Replace worn power cords and/or loose plugs. exposed to water and/or weather. 21. Be sure water connections have a shut-off valve 10. Do not tamper with the controls. and that fill hose connections are tight. CLOSE the shut-off valves at the end of each wash day. 11. Do not repair or replace any part of the washer, or attempt any servicing unless specifically 22. Loading door MUST BE CLOSED any time the recommended
Краткое содержание страницы № 8
Safety Information WARNING WARNING This machine must be installed, adjusted, Never touch internal or external steam and serviced by qualified electrical pipes, connections, or components. maintenance personnel familiar with the These surfaces can be extremely hot and construction and operation of this type of will cause severe burns. The steam must machinery. They must also be familiar be turned off and the pipe, connections, with the potential hazards involved. and components allowed to co
Краткое содержание страницы № 9
Safety Information Operator Safety Safe Operating Environment Safe operation requires an appropriate operating WARNING environment for both the operator and the machine. If questions regarding safety arise, contact the NEVER insert hands or objects into manufacturer immediately. basket until it has completely stopped. Doing so could result in serious injury. Environmental Conditions SW012 • Ambient Temperature. Water in the machine will To ensure the safety of machine operators, the freez
Краткое содержание страницы № 10
Safety Information Input and Output Services DANGER • Water Pressure. Best performance will be realized if water is provided at a pressure of Do not place volatile or flammable fluids 30 – 80 psi (2.0 – 5.4 bar). Although the machine in any machine. Do not clean the machine will function properly at lower pressure, with volatile or flammable fluids such as increased fill times will occur. Water pressure acetone, lacquer thinners, enamel higher than 100 psi (6.7 bar) may result in reduc
Краткое содержание страницы № 11
Safety Information AC Inverter Drive This manual is designed as a guide to operating and maintaining the Pocket Hardmount washer-extractor Machines equipped with the AC inverter drive require equipped with the AC inverter drive. special attention with regard to the operating environment. NOTE: All information, illustrations, and specifications contained in this manual are based • An especially dusty or linty environment will on the latest product information available at the require mor
Краткое содержание страницы № 12
Introduction Model Identification Information in this manual is applicable to these models: UW35TV UWL060T3M UWN060T3M UWU060T3M UW60TV UWL060T3V UWN060T3V UWU060T3V UW80TV UWL080T3V UWN080T3V UWU080T3V UW100TV UWL100T3V UWN100T3V UWU100T3V UW125TV UWL125T3V UWN125T3V UWU125T3V UW150TV UWL150T3V UWN150T3V UWU150T3V UWL035T3V UWN035T3V UWU035T3V UWL060T3L UWN060T3L UWU060T3L F8138801 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 10
Краткое содержание страницы № 13
Introduction Nameplate Location Replacement Parts The nameplate is located on the back of the machine If literature or replacement parts are required, contact and is programmed in the UniLinc Control. To access the source from which the washer-extractor was Machine ID through the control: purchased or contact Alliance Laundry Systems LLC at (920) 748-3950 for the name of the nearest 1. Press and hold , then , then authorized parts distributor. A parts manual may be keypads at the same time
Краткое содержание страницы № 14
Introduction rd Model Number Familiarization Guide - Models through May 3 , 2009 Sample Model Number: UW060TVQU10001 Model Number Prefix UW Washer-Extractor Capacity (60 pounds dry weight of laundry) 060 Type of Electrical Control T = UniLinc Computer T Washer-Extractor Speed Capabilities V = 8 Speeds V Electrical Characteristics Q Design Series U1 Option Identification (varies from machine to machine) 0001 th Model Number Familiarization Guide - Models starting May 4 , 2009 Sample Model Number
Краткое содержание страницы № 15
Preliminary Information Audit Information About the Control The control collects and stores audit information, The UniLinc control on the washer-extractor is an which can be accessed with a PDA. Refer to the advanced, graphical, programmable computer that lets following list for available audit information with a the owner control most machine features by PDA. Refer to UniLinc PC and PDA Application interacting with the control. User Instructions. UniLinc allows the owner to program cus
Краткое содержание страницы № 16
Preliminary Information IR Communications Menu Restore to Factory Defaults When the user selects Restore All Cycles And Global Settings To Factory-Defaults, the control resets all of the default values. The control also resets Machine Cycles #1 through #41. The control will also reset the following to factory-defaults: Default Washer-Extractor Settings Language = English Maximum Balance Retries = 3 Water Reuse = Disabled Rapid Advance = Enabled Water Recirculation = Disabled PHM1003R Exter
Краткое содержание страницы № 17
Preliminary Information *Manual Programming = Enabled *If manual programming is disabled, programming changes to UniLinc can only be made with an external communication device. Refer to UniLinc PC and PDA Applications User Instructions. Refer to Factory Defaults, Menu section for information on Restoring Factory Defaults. Entering Program Mode 1. Press and hold , then , then to enter the System Menu. Select Program to enter programming options. F8138801 © Copyright, Alliance Laundry Syste
Краткое содержание страницы № 18
UniLinc Identification Operational Keypad The control includes seven keypads. These functions are available to the operator and are intended to control and manage operation of the washer-extractor. Refer to Figure 5 and Table 1. PHM1401C Figure 5 Keypad Description Press to move the cursor on display to edit programming values. Also, press while in Cycle Menu or Run Menu to change to the Contrast Adjust/Backlight LCD/UP ARROW Menu. Also, press with and to enter System Menu. Press to move
Краткое содержание страницы № 19
UniLinc Identification Stop Mode Operation Modes If keypad is pressed before cycle ends, control General Modes of Operation enters Stop Mode and performs the following steps: In each mode of operation, the user may press keypads • Displays a hourglass. or communicate with the control to change the displayed menu. • Turns off all outputs. • Verifies water is drained. Power-up Mode • Verifies motor is stopped by either rotation The control enters this mode at power-up. After the sensor or ti
Краткое содержание страницы № 20
Machine Cycle Definition and Operation There are 41 machine cycles which can be selected Delayed Start Feature and run. Machine cycles can be modified or made The user can select a machine cycle to run at a later “unavailable” by manually editing them in Modify time. Refer to Delayed Start Menu Section. Cycle Menu or by using the PDA to download a modified machine cycle into the control. Machine Jog Feature UW150 Only cycles cannot be deleted, but can be made “unavailable” so that they ar
