Краткое содержание страницы № 1
LCD Entertainment Ready
Installation Instructions
Краткое содержание страницы № 2
Краткое содержание страницы № 3
CORPORATE HEADQUARTERS 10601 West Belmont Avenue Franklin Park, Illinois 60131 • U.S.A. 847.288.3300 • FAX: 847.288.3703 800.735.3867 (Toll-free within U.S.A., Canada) INTERNATIONAL OFFICES LIFE FITNESS ASIA PACIFIC LTD LIFE FITNESS EUROPE GMBH Room 2610, Miramar Tower Siemensstrasse 3 132 Nathan Road 85716 Unterschleissheim Tsimshatsui, Kowloon GERMANY HONG KONG Telephone: (+49) 89.31 77 51.0 Telephone: (+852) 2891.6677 FAX: (+49) 89.31 77 51.99 FAX: (+852) 2575.6001 LIFE FITNESS ITALIA S.R.L.
Краткое содержание страницы № 4
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi- dential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications. However, there is no guarantee that interf
Краткое содержание страницы № 5
TABLE OF CONTENTS Section Description Page 1. Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Models New 95Ti Treadmill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Models 95Li Summit Trainer . . . . .
Краткое содержание страницы № 6
IMPORTANT SAFETY INSTRUCTIONS • DANGER: To reduce the risk of electrical shock, always unplug this Life Fitness product before cleaning or attempting any maintenance activity. • WARNING: To reduce the risk of burns, fire, electric shock, or injury, it is imperative to connect each prod- uct to a properly grounded electrical outlet. • WARNING: To prevent injury, this product must be securely attached in accordance with the installation instructions. • Never operate a Life Fitness product if it ha
Краткое содержание страницы № 7
CONSIGNES DE SECURITE IMPORTANTES • DANGER: Pour réduire les risques de décharge électrique, toujours débrancher cet appareil Life Fitness avant le nettoyage ou toute mesure d'entretien. • AVERTISSEMENT: Pour réduire les risques de brûlures, d'incendies, de décharges électriques ou de blessures, chaque appareil doit absolument être branché sur une prise électrique correctement mise à la terre. • AVERTISSEMENT Pour prévenir les blessures, ce produit doit être solidement fixé, conformément aux ins
Краткое содержание страницы № 8
INSTALLATION Note to the CATV Installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the ground- ing system of the building as close to the point of cable entry as practical. Antenna Grounding According to the NEC Antenna Grounding According to the National Electrical Code, ANSI/NFPA 70. 1. Antenna lead in wire 2. Antenn
Краткое содержание страницы № 9
MODELS NEW 95TI TREADMILLS TOOLS REQUIRED: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench PARTS NOT USED FROM KIT: (1) Main Bracket Cap, (1) Grommet 1. Turn off the treadmill and unplug it from the power outlet. 2. Remove the six SCREWS securing the MOTOR COVER. Remove the MOTOR COVER and set it and the screws aside. 3. Remove the protective liner from one of the provided FASTENER STRIPS. Attach the fastener strip to the bottom of the POWER BLOCK (1). Interlock the remaining FASTENER
Краткое содержание страницы № 10
INSTALLATION 19. With the remaining TV BRACKET (15) oriented as shown, install it to the back of the TV (16) using four SCREWS (17) and WASHERS (6). Tighten the SCREWS securely. (8-10 ft. lbs.) NOTE: Be sure the side holes of the TV BRACKET are oriented as shown. 20. Position the TV BRACKETS (8 & 15) together as shown below and secure them together using one BOLT (18), WASHER (19) and NUT (20). Leave the BOLT and NUT loose at this time. NOTE: Be sure the PIVOT POST of the TV BRACKET (15) engages
Краткое содержание страницы № 11
MODELS NEW 95X CROSS-TRAINERS TOOLS REQUIRED: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench PARTS NOT USED FROM KIT: (1) Main Bracket Cap, (1) Grommet 1. Remove the protective liner from one of the provided FASTENER STRIPS. Attach the fastener strip to the bottom of the POWER BLOCK (--). Interlock the remaining FASTENER STRIP to the installed FASTENER STRIP. Remove the remaining protective liner from FASTENER STRIP and secure the POWER BLOCK to the underside of the CENTER FRAME as s
Краткое содержание страницы № 12
INSTALLATION 9. Tilt the DISPLAY CONSOLE (--) forward and connect the I-R CONTROL (A) and S-VIDEO (--) CABLES to the back of the DIS- PLAY CONSOLE. 10. Tape the ends of the all CABLES (POWER, COAXIAL, I-R CONTROL, S-VIDEO) together. 11. Feed the taped end of the MEDIA CABLES (--) through the large hole in the back of the CONSOLE BRACKET (--). Carefully pull excess MEDIA CABLE through the CONSOLE BRACKET . 12. Slide one GROMMET (--) over the taped end of the MEDIA CABLES (--). 13. Holding the MAI
Краткое содержание страницы № 13
® MODELS NEW 95C UPRIGHT LIFECYCLE EXERCISE BIKES TOOLS REQUIRED: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench PARTS NOT USED FROM KIT: (1) Main Bracket Cap, (1) Grommet J 1. Remove the protective liner from one of the provided FASTENER STRIPS. Attach the fastener strip to the bottom of the POWER BLOCK (-- ). Interlock the remaining FASTENER STRIP to the installed FASTENER J J STRIP. Remove the remaining protective liner from FASTENER STRIP and secure the POWER BLOCK to the undersi
Краткое содержание страницы № 14
INSTALLATION A 9. Tilt the DISPLAY CONSOLE (--) forward and connect the I-R CONTROL (A) and S-VIDEO (--) CABLES to A A the back of the DISPLAY CONSOLE. A 10. Tape the ends of the all CABLES (POWER, A COAXIAL, I-R CONTROL, S-VIDEO) together. A 11. Feed the taped end of the MEDIA CABLES (--) through the large hole in the back of the CONSOLE BRACKET (--). Carefully pull excess MEDIA CABLE through the CONSOLE BRACKET . 12. Slide one GROMMET (--) over the taped end of the MEDIA CABLES (--). 13. Holdi
Краткое содержание страницы № 15
® MODELS NEW 95R RECUMBENT LIFECYCLE EXERCISE BIKES TOOLS REQUIRED: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench PARTS NOT USED FROM KIT: (1) Main Bracket Cap, (1) Grommet 1. Remove the protective liner from one of the provided FASTENER STRIPS. Attach the fastener strip to the bottom of the POWER BLOCK (--). Interlock the remaining FASTENER STRIP to the installed FASTENER STRIP. Remove the remaining protective liner from FASTENER STRIP and secure the POWER BLOCK to the underside of
Краткое содержание страницы № 16
INSTALLATION 9. Tilt the DISPLAY CONSOLE (--) forward and connect the I-R CON- A TROL (A) and S-VIDEO (--) CABLES to the back of the DIS- A A PLAY CONSOLE. 10. Tape the ends of the all CABLES (POWER, COAXIAL, I-R A CONTROL, S-VIDEO) together. A 11. Feed the taped end of the MEDIA CABLES (--) through the A large hole in the back of the CONSOLE BRACKET (--). Carefully pull excess MEDIA CABLE through the CONSOLE BRACKET . 12. Slide one GROMMET (--) over the taped end of the MEDIA CABLES (--). 13. H
Краткое содержание страницы № 17
MODELS 95LI SUMMIT TRAINER TOOLS REQUIRED: Metric Hex Key Set, Side Cutters, T-45 Torx Wrench 1. Remove the CONSOLE SUPPORT TOP CAP (a). 2. Remove the two SCREWS (b) securing the CONSOLE SUPPORT COVER (c). Remove the CONSOLE SUPPORT COVER and set it and the SCREWS aside. 3. Remove the four SCREWS (d) securing the DISPLAY CONSOLE (e). Set the SCREWS aside. Tilt the CONSOLE forward and disconnect all cables. Set the CONSOLE aside. 4. Locate the REMOTE CONTROL (f). Configure the MOUNTING BRACKET (g
Краткое содержание страницы № 18
INSTALLATION ® MODELS 95CI, 93C, 90C UPRIGHT LIFECYCLE EXERCISE BIKES TOOLS REQUIRED: Metric Hex Key Set, Side Cutters NOTE: Proceed with the following steps before attaching the DISPLAY CONSOLE and ACCESSORY TRAY as described in the Assembly Instructions. 1. Locate the SPACER (a). With the SPACER oriented as shown, feed all the CONSOLE CONNECTORS, POWER CORD, and COAXIAL CABLE through the large center hole in the SPACER. Slide the SPACER onto the CONSOLE MOUNTING PLATE () making sure the top of
Краткое содержание страницы № 19
10. Attach the ADAPTER BRACKET (AA) to the ENTERTAINMENT CONSOLE (k) to the using four SCREWS (BB). Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS. Attach the ENTERTAINMENT CONSOLE to the UPPER MOUNTING PLATE (m) using four SCREWS (n) and WASHERS (o). Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS. 11. Connect the COAXIAL CABLE, POWER CORD and REMOTE CABLE (g) to the rear of the ENTERTAINMENT CONSOLE (k) as shown under Console Cable Connections at the end of thi
Краткое содержание страницы № 20
INSTALLATION ® MODELS 95RI, 93R, 90R RECUMBENT LIFECYCLE EXERCISE BIKES TOOLS REQUIRED: Metric Hex Key Set, Side Cutters NOTE: Proceed with the following steps before attaching the DISPLAY CONSOLE as described in the Assembly Instructions. 1. Locate the SPACER (a). With the SPACER oriented as shown, feed all the CONSOLE CONNECTORS, POWER CORD, and COAXIAL CABLE through the large center hole in the SPACER. Slide the SPACER onto the CONSOLE MOUNTING PLATE (b) making sure the top of the SPACER hook
