Краткое содержание страницы № 1
9” Angle Grinder
93179
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
© ®
Copyright 2005 by Harbor Freight Tools . All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in any shape or form without
the express written consent of Harbor Freight Tools.
For technical que
Краткое содержание страницы № 2
Specifications Molded ABS Motor Housing 120 VAC, 60 Hz SIngle Phase Construction: Power Requirement: Cast Aluminum Gear Housing 11.0 no load Amps, 1320 Watts 9" with 5/8" x 11TPI Arbor Spindle MM otor Speed: 6500 RP Wheel Diameter: * optional 7/8" Arbor Adaptor included OH verall Dimensions:1: 8-1/2"L x 4-3/8"W x 5-1/2"Pd ower Cord 82"L x 14AWG 2 prong polarize Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance proc
Краткое содержание страницы № 3
Personal Safety 10. Stay alert. Watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. 11. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving p
Краткое содержание страницы № 4
Service 23. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 24. When servicing a tool, use only identical replacement parts. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. Specific Safety Rules 1. Maintain labels and nameplates on the tool. These carry important information. If unreadable or missing, contact Harb
Краткое содержание страницы № 5
GROUNDING WARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed
Краткое содержание страницы № 6
EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (See Figure C, below.) 3. The smaller the gauge number of the wire, the greater the capacity of the cord. For example,
Краткое содержание страницы № 7
Unpacking When unpacking, check to make sure that the product is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. Assembly You must install the Wheel Guard (3) before using your Angle Grinder 1. Align the tabs on the Wheel Guard (3) with the indents in the underside of the Gear Housing (19) and press the Guard into place as shown in the photo at right. 2. Rotate the Wheel Guard (3) into position as shown in the
Краткое содержание страницы № 8
You must install the Grinding Wheel (54) before using your tool. 1. Place the Backing Washer (2) on the Arbor Spindle (7) as shown, making sure it fits tight. 2. Place the Grinding Wheel (54) on top of the Backing Washer (2), making sure the bore of the Grinding Wheel fits onto the step of the Arbor Spindle (7). 3. Place the Disc Locking Nut (1) onto the Arbor Spindle (7) with the concave recessed side against the grinding wheel. 4. Press in and hold the Spindle Lock (22). Be sure that the Spind
Краткое содержание страницы № 9
Rotating the Back Handle You can rotate the Back Handle (41, 48) by pressing the Rotation Button (53). 1. First unplug the tool. 2. Hold the Main Body of the tool with one hand. With the other grip the Back Handle and press in the Rotation Button. 3. Rotate the Back Handle to the desired position. You can rotate the handle up to 90° in either Rotating the Back Handle direction. Release the Rotation Button. WARNING: The Handle must be used at all times. to NOTE: The motor will heat up as it is us
Краткое содержание страницы № 10
Maintenance and Inspection 1. The Armature (31) and Stator (36) comprise the main part of the tool. Protect these electrical components from moisture or oil intrusion. 2. Inspect the Carbon Brushes (50) regularly. Replace them if they are more than 1/3 worn or are chipped or cracked. When handling them, be careful not to damage them. To reduce wear after inspection, replace them in exactly the same way as they were removed. 3. Regularly inspect all components and fasteners to be sure they are pr
Краткое содержание страницы № 11
Parts List Description Part # Description Part # DISC LOCKING NUT 1 BEARING COVER 29 BACKING WASHER 2 KEY 2.9X5X13 30 WHEEL GUARD 3 ARMATURE 31 GUARD CLAMP 4 BALL BEARING 629.2Z 32 SCREW M8X28 5 BEARING BUSHION 33 KEY 4X5X13 6 GUIDE WIND CIRCLE 34 ARBOR SPINDLE 7 SCREW ST5X80 35 SCREW M5X16 8 STATOR 36 SPRING WASHER *5 9 CONNECTION SPRING 37 GEAR HOUSING COVER 10 NAME PLATE 38 BALL BEARING 6202RS 11 HOUSING 39 BEARING COVER 12 TYPE PLATE 40 SCREW M4X10 13 BACK HANDLE(RIGHT) 41 SPRING WASH
Краткое содержание страницы № 12
Assembly Drawing * Grinding Wheel - Part 54 - not shown REV 02/06 SKU 93179 For technical questions, please call 1-800-444-3353 Page 12
