Краткое содержание страницы № 1
Angle Grinder
MODEL 9067L
MODEL 9067DB
001011
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Краткое содержание страницы № 2
SPECIFICATIONS Model 9067L 9067DB Wheel diameter 180 mm (7”) 180 mm (7”) No load speed (RPM) 6,000/min 8,500/min Overall length 458 mm (18”) 458 mm (18”) Net weight 4.2 kg (9.3 lbs) 4.2 kg (9.3 lbs) Spindle thread 5/8” 5/8” • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may re
Краткое содержание страницы № 3
5. Avoid body contact with grounded sur- 14. Use safety equipment. Always wear eye faces such as pipes, radiators, ranges and protection. Dust mask, non-skid safety refrigerators. There is an increased risk of shoes, hard hat, or hearing protection must electric shock if your body is grounded. be used for appropriate conditions. Ordinary eye or sun glasses are NOT eye protection. 6. Do not expose power tools to rain or wet conditions. Water entering a power tool will Tool Use and Care increase t
Краткое содержание страницы № 4
24. When servicing a tool, use only identical SERVICE replacement parts. Follow instructions in 23. Tool service must be performed only by the Maintenance section of this manual. qualified repair personnel. Service or main- Use of unauthorized parts or failure to follow tenance performed by unqualified personnel Maintenance instructions may create a risk of could result in a risk of injury. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. W
Краткое содержание страницы № 5
cracked or damaged wheel immediately. 14. Before using the tool on an actual work- Run the tool (with guard) at no load for piece, let it run for a while. Watch for about a minute, holding tool away from vibration or wobbling that could indicate others. If wheel is flawed, it will likely sep- poor installation or a poorly balanced arate during this test. wheel. 7. Use only flanges specified for this tool. 15. Use the specified surface of the wheel to perform the grinding. 8. Be careful not to da
Краткое содержание страницы № 6
SYMBOLS USD292-1 The followings show the symbols used for tool. V ....................... volts ....................no load speed n ˚ A ....................... amperes ....................Class II Construction .............. alternating current .../min................revolutions or reciprocation per minute .............. alternating or direct current 6
Краткое содержание страницы № 7
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 001026 Shaft lock CAUTION: 1 • Never actuate the shaft lock when the spindle is moving. The tool may be damaged. Press the shaft lock to prevent spindle rotation when install- ing or removing accessories. 1. Shaft lock 001041 Switch action CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns t
Краткое содержание страницы № 8
ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 001057 Installing side grip (handle) CAUTION: • Always be sure that the side grip is installed securely before operation. Screw the side grip securely on the position of the tool as shown in the figure. 001064 Installing or removing wheel guard 1 CAUTION: • When using a depressed center grinding wheel/Multi- disc, flex wheel or wire wheel brush, the wheel guard must be fitted
Краткое содержание страницы № 9
001089 To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and 1 securely tighten clockwise. To remove the wheel, follow the installation procedure in reverse. 2 1. Lock nut wrench 2. Shaft lock 001101 Installing or removing flex wheel 1 (optional accessory) 2 3 WARNING: 4 • Always use supplied guard when flex wheel is on tool. Wheel can shatter during use and guard helps to reduce chances of personal injury. Follow instructions
Краткое содержание страницы № 10
OPERATION WARNING: • It should never be necessary to force the tool. The weight of the tool applies adequate pressure. Forcing and excessive pressure could cause dangerous wheel breakage. • ALWAYS replace wheel if tool is dropped while grinding. • NEVER bang or hit grinding disc or wheel onto work. • Avoid bouncing and snagging the wheel, especially when working corners, sharp edges etc. This can cause loss of control and kickback. • NEVER use tool with wood cutting blades and other sawblades. S
Краткое содержание страницы № 11
Unplug tool and place it upside down allowing easy access to spindle. Remove any accessories on spindle. Mount ure- thane washer then thread wire cup brush onto spindle and tighten with supplied wrench. When using brush, avoid applying too much pressure which causes over bending of wires, leading to premature breakage. NOTE: • When using wire cup brush, mount urethane washer to the spindle. It will make it easier to remove wire cup brush. 001234 Operation with wire wheel brush (optional accesso
Краткое содержание страницы № 12
MAINTENANCE 001167 CAUTION: 1 • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. The tool and its air vents have to be kept clean. Regularly 2 clean the tool’s air vents or whenever the vents start to become obstructed. 1. Exhaust vent 2. Inhalation vent 001146 Replacing carbon brushes When the resin insulating tip inside the carbon brush is 2 exposed to contact the commutator, it will automatically shut off the motor. When this o
Краткое содержание страницы № 13
from your Makita distributor or factory service center, be sure to obtain and use all necessary fasteners and guards as recommended in this manual. Your failure to do so could result in personal injury to you and others. If you need any assistance for more details regarding these accessories, ask your local Makita service center. 001184 1 2 2 8 2 12 3 3 9 11 13 4 6 10 5 7 5 9067L/9067DB 1Grip 36 2 Wheel guard (Wheel cover) 3 Inner flange 89 4 Depressed center grinding wheel/Multi-disc 5 Lock nut
Краткое содержание страницы № 14
Memo 14
Краткое содержание страницы № 15
Memo 15
Краткое содержание страницы № 16
Memo 16
Краткое содержание страницы № 17
Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitby, Ontario L1N 7B7 Fold 17 Cut
Краткое содержание страницы № 18
Your answers to the following questions are appreciated. 1. This product was purchased from? 3. How did you first learn of Makita Power Tools? Hardware/lumber Store Industrial Supply Magazine/Newspaper Catalog Tool Distributor Other ( ) From dealer Other ( ) Store display 2. Use of the product is intended for? 4. Most favored points are? Construction trade Home maintenance Design Makita Brand Industrial maintenance Other ( ) Features Power Size
Краткое содержание страницы № 19
Factory Service Centres Head Office: 1950 Forbes St., Whitby, Ontario, L1N 7B7 (905) 571 - 2200 1-800-263-3734 Regional Office: 11771 Hammersmith Way, Richmond B.C. V7A 5H6 (604) 272 - 3104 1-800-663-0909 Regional Office: 6389 boul. Couture, St. Leonard, Quebec (Montreal) H1P 3J5 (514) 323 - 1223 1-800-361-7049 Dartmouth: 202 Brownlow Avenue Dartmouth, N.S., B3B 1T5 (902) 468 - 7064 1-888-625-4821 Ville St. Laurent: 1140 Rue Bégin, Ville St. Laurent, Quebec (Montreal) H4R 1X1 (514) 745 -
Краткое содержание страницы № 20
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centres. If inspection shows the trouble is caused by defective workmanship or material, M
