Краткое содержание страницы № 1
If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contáctenos.
1-800-4-De WALT • www.dewalt.com
InstruCtIon ManuaL
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
GuIDe D'utILIsatIon DE GARANTÍA. aDVertenCIa: LÉASE ESTE INSTRUCTIVO ANTES
DE USAR EL PRODUCTO.
ManuaL De InstruCCIones
DPD3000IC
Pressure Washer
Laveuse à pression
Lavadora a presión
Краткое содержание страницы № 2
B C FIG. 1 A DPD3000IC Pressure Washer P A. Panel assembly I. Starter grip O L N B. Nozzle holder J. Engine C. Professional Spray gun K. Choke control K M D. Side Handle L. Throttle control lever E. Quick-connect M. Fuel valve lever spray wand N. Gas cap F. Frame O. Handle assembly Q D G. Engine dipstick/oil plug P. High-pressure hose H. Engine switch J Q. High-pressure pump E I F Engine Refer to the engine instruction manual for location and operation of other engine controls. G
Краткое содержание страницы № 3
English Specifications MODEL WEIGHT HEIGHT WIDTH LEGTH n PSI MA* x AVERAGE GPM MAx* AVERAGE EnGIE n OPERATIn G OPERATIn G PSI GPM DPD3000IC 83.6 lbs 26.5" 23" 40" 3000 2750 2.8 2.7 De WALT (20384 kPa) (18961 kPa) (10.6 L/min) (10.3 L/min) 196 cc OHV, 5.5 Net HP, 6.5 Gross HP ** * Maximum PSI and GPM ratings determined in accordance with the Pressure Washers Manufacturers Association (PWMA) standard PW101 ** Horsepower rating (shown as maximum output @ 3600 rpm) is in accordance with SAE
Краткое содержание страницы № 4
7. Do not overreach or stand on unstable support. Keep good footing and balance at all times. 8. Follow the maintenance instructions specified in the manual. DANGER: RISk Of I Nj ECTION OR SEvERE INj URy. kEEP DANGER: RISk Of ExPl OSION OR f IRE ClEAR Of NOzzlE. DO NOT DIRECT DISChARGE STREAm AT What can happen how to prevent it PERSONS. ThIS PRODUCT IS TO BE USED ONly By T RAINED OPERATORS. • S p i l l e d g a s o l i n e a n d i t ’ s • S h u t o f f e n g i n
Краткое содержание страницы № 5
English • Muffler e xhaust heat can • A l w a y s k e e p p r e s s u r e w a s h e r DANGER: RISk TO BREAThING (ASPhyxIATION) CONTINUED damage painte d surf ac es, a mini m um of 4' (1.2 m) away melt any material sensi tive from surf ace s (such as • S o m e c l e a n i n g f l u i d s • Use only cleaning fluids to heat (such as siding, houses, aut o mob iles or con tain substanc es which specif i cal ly recom mend ed could cause injury to skin,
Краткое содержание страницы № 6
DANGER: RISk Of flUID INjECTION AND lACERATION CONTINUED • Y o u r p r e s s u r e w a s h e r • D i r e c t s p r a y a w a y f r o m s e l f DANGER: RISk Of INjUR y fROm SPRAy operates at fluid pressures and others. What can happen how to prevent it and velocities high enough to • M a k e s u r e h o s e a n d f i t t i n g s penetrate human and • H i g h - v e l o c i t y f l u i d s p r a y • A l w a y s w e a r A N S I - a p p r o v e
Краткое содержание страницы № 7
English • If proper star ting procedure • If engine does not star t after is not followed, engine can two pulls, squeeze trigger kickback causing serious of gun to relieve pump DANGER: RISk Of UNSAfE OPERATION hand and arm injury. pressure. Pull starter cord slowly until resistance is felt. What can happen how to prevent it Then pull cord rapidly to avoid • Unsaf e oper a tion of y our • Do not use chlor ine kickback and prevent hand or pressure wash
Краткое содержание страницы № 8
DANGER: RISk Of I Nj URy OR PROPE R Ty DAmAGE WhEN WARNING: RISk Of B URSTING TRANSPORTING OR STORING What can happen how to prevent it What can happen how to prevent it • Over inflation of tires could • Use a tire pressure gauge to • F u e l o r o i l c a n l e a k o r s p i l l • If pressure w asher is equipped result in serious injury and check the tires pressure before and could result in fire or with a fuel shut-off valve, turn property damage. each use
Краткое содержание страницы № 9
English WARNING: RISk Of ElEC TRI CAl ShOCk WARNING: RISk Of hOT SURf ACES What can happen how to prevent it What can happen how to prevent it • S p r a y d i r e c t e d a t e l e c t r i c a l • U n p l u g a n y e l e c t r i c a l l y • Con tact with hot sur f aces , • D u r i n g o p e r a t i o n , t o u c h outlets or switches , or obj ects op er at ed product before such as engines exhaust only the control surfaces conn ec
Краткое содержание страницы № 10
note: The high-pressure pump was filled with oil at the factory. InSTALLATIon Always check oil level before using (refer to Maintenance for more Pressure Washer Assembly (Fig. 1) information). 1. Place handle assembly (O) onto frame, depress WARNING: Risk of bursting. Use a tire pressure gauge to check the the snap buttons, and slide the handle assembly tires pressure before each use and while inflating tires; see the tire side- onto the frame (F) until snap buttons are secured wall for t
Краткое содержание страницы № 11
English ChanGInG nozzLes on sPray WanD nozzle Color spray Pattern uses surfaces* DANGER: Risk of fluid injection. Do not direct discharge stream 0˚ powerful metal or toward persons, unprotected skin, eyes or any pets or animals. pinpoint for concrete; Serious injury will occur. red very intense DO NOT use WARNING: Flying objects could cause risk of serious injury. DO cleaning on wood NOT attempt to change nozzles while pressure washer is running. Turn engine off before changing nozzles. 15
Краткое содержание страницы № 12
3. Install low-pressure (black) nozzle into quick connect fitting of spray • DO NOT let hoses come in contact with very hot engine wand, refer to spray Wand nozzles. note: Chemicals and soaps muffler during or immediately after use of your pressure will not siphon if the black soap nozzle is not installed on the washer. Damage to hoses from contact with hot engine spray wand. surfaces will NOT be covered by warranty. 4. After use of chemicals, place chemical hose into container of clean
Краткое содержание страницы № 13
English 4. Verify the filter screen (U) is in water inlet of pump. note: Do not allow the starter grip to snap back. Return it gently The cone side faces out. by hand. 5. Connect the cold water source (V) to pump inlet. WARNING: Risk of unsafe operation. If engine does not start after two pulls, squeeze trigger of gun to relieve pump pressure. Pull note: Water source must provide a minimum of starter cord slowly until resistance is felt. Then pull cord rapidly to 5 gallons per minute at
Краткое содержание страницы № 14
3. Place the fuel valve lever (M) in the OFF Change pump oil after the first 10 hours of operation and every 250 postion. hours thereafter. CAUTION: Risk of property damage. Never t o CheCk oIL turn water supply off while pressure washer The oil level should come to the dot in the middle engine is running or damage to pump will result. BB of the sight glass (AA). 4. Turn water source off. ho W t o ChanGe PuMP oIL 5. Pull trigger on spray gun to relieve any water 1. Loosen pump oil fill
Краткое содержание страницы № 15
English 5. Direct water supply into spray wand to Pump back flush loosened particles for 30 The manufacturer recommends using a pump protector/winter- seconds. izer, such as De WALT winterizer (DP80) when storing the unit 6. Reassemble the nozzle to the wand. for more than 30 days and/or when freezing temperatures are 7. Reconnect spray wand to gun then turn on water supply. expected. De WALT winterizer (DP80) is availabe at the store 8. Start pressure washer and place spray wand into
Краткое содержание страницы № 16
WARNING: The use of any other accessory not recommended for Pressure Washer use with this tool could be hazardous. Use only accessories rated 1. Drain all water from high- equal to or higher than the rating of the pressure washer. pressure hose, coil it and store it in cradle of the pressure washer SErvIcE InForMATIon handle. Please have the following information available for all service calls: 2. With nozzle pointed down and Model Number ____________ Serial Number ___________ the sp
Краткое содержание страницы № 17
English washer operation. Normal wear parts include, but are not limited to, the engine air filter, spark plug, pump valve seals and O rings. This warranty does not apply to accessories or damage caused where repairs have been made or attempted by a repair center not autho- rized by De WALT. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces. For further details of warranty coverage and warranty repair informa- tion, vis
Краткое содержание страницы № 18
Glossary Bypass mode: Allows water to re-circulate within pump when the gun trigger is not pulled. Chemical hose: Feeds cleaning agents into the pump to mix with the water. Refer to Chemicals and Cleaning Solvents. Chemical injection system: Mixes cleaners or cleaning solvents with water to improve cleaning effectiveness. Choke control: Opens and closes carburetor choke valve. Cu: Cleaning Units. GPM multiplied by PSI. (GPM x PSI = CU) Fuel valve lever: Opens/closes connection between fuel tank
Краткое содержание страницы № 19
English (Troubleshooting codes cont.) Troubleshooting codes CoDe PossIBLe Cause PossIBLe soLutIon 1 No fuel. Add fuel. 2 Low oil. Add required amount of oil. 3 Pressure builds up after two pulls on the recoil starter or after initial Squeeze gun trigger to relieve pressure . use. 4 Choke lever in the NO CHOKE position. Move choke to the CHOKE posi tion. 5 Spark plug wire not attached. Attach spark plug wire. 6 Engine ON/OFF switch in OFF posi tion. Place engine ON/OFF switch in ON position. 7
Краткое содержание страницы № 20
(Troubleshooting codes cont.) CoDe PossIBLe Cause PossIBLe soLutIon 17 Spray wand not in low pressure. See spray Wand nozzles under Operation. 18 Chemical filter clogged. Clean filter. 19 Chemical screen not in cleaning solution. Make sure end of chemical hose is fully submerged into cleaning solution. 20 Chemical too thick. Dilute chemical. Chemical should be the same consistency as water. 21 Worn seal or packing. Have parts cleaned or replaced by authorized service center. 22 Chemical build u
