Руководство по эксплуатации Elkay EDFP210FPC

Краткое содержание страницы № 1

EDFP210FP*B EDFP214FP*B EDFP217FP*B
Installation/Care/Use Manual
EDFP210FPC EDFP214FPC EDFP217FPC
™
Soft Sides Freeze Resistant Fountains
EDFP210FPC EDFP214FPC EDFP217FPC
Installer
To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE
INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLA-
TION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER APPLICABLE
CODES. After installation, leave these instructions inside the fountain for future reference

Краткое содержание страницы № 2

EDFP210FP*B EDFP214FP*B EDFP217FP*B 97565C (Rev. J - 8/07) PAGE 2 EDFP210FP/EDFP214FP MOUNTING BOLT AND ACCESS HOLE LAYOUT FIG. 1 LEGEND A = MOUNTING BOLT LOCATIONS (4) (3/8" DIA. NOT PROVIDED) B = 7/8" DIA. (22mm) HOLE FOR WATER SUPPLY TUBE C = 7/8" DIA. (22mm) HOLE FOR OPERATING CABLE D = 1-3/4" (44mm) HOLE FOR WASTE LINE FINISHED FLOOR

Краткое содержание страницы № 3

EDFP210FP*B EDFP214FP*B EDFP217FP*B 97565C (Rev. J - 8/07) PAGE 3 EDFP210FP/EDFP214FP ROUGH-IN DRAWINGS FIG. 2 FINISHED FLOOR 1. Wall should already be framed for the fountain using dimensions shown in Fig. 1. Shown dimensions pertain to installation location. These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only). 2. Remove bottom cover from fountain and save the screws. 3. Install the fountain using bolts and washers (not p

Краткое содержание страницы № 4

EDFP210FP*B EDFP214FP*B EDFP217FP*B 97565C (Rev. J - 8/07) PAGE 4 EDFP217FP MOUNTING BOLT AND ACCESS HOLE LAYOUT FIG. 3 FINISHED FLOOR LEGEND A = 3/8" DIA. (10mm) SLOTS (FOR MOUNTING UPPER HANGER BRACKET) B = 7/8" DIA. (22mm) HOLE FOR WATER SUPPLY TUBE C = 7/8" DIA. (22mm) HOLE FOR OPERATING CABLE D = MOUNTING BOLT LOCATIONS (8) (3/8" DIA. NOT PROVIDED) E = 1-3/4" (44mm) HOLE FOR WASTE LINE

Краткое содержание страницы № 5

EDFP210FP*B EDFP214FP*B EDFP217FP*B 97565C (Rev. J - 8/07) PAGE 5 EDFP217FP ROUGH-IN DRAWINGS FIG. 4 FINISHED FLOOR 1. Wall should already be framed for the fountains using dimensions shown in Fig. 3. Shown dimensions pertain to installation location. These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only). 2. Remove bottom covers from fountains and save the screws. 3. Install the fountains using bolts and washers (not provide

Краткое содержание страницы № 6

EDFP210FP*B EDFP214FP*B EDFP217FP*B CABLE SHEATH ADJUSTMENT To Increase Free Play To Reduce Free Play FIG. 5 FIG. 6 See Fig. 9 FIG. 7 See Fig. 5 FIG. 8 FIG. 9 97565C (Rev. J - 8/07) PAGE 6

Краткое содержание страницы № 7

EDFP210FP*B EDFP214FP*B EDFP217FP*B The freeze resistant package must be mounted on an interior wall in a heated area. The room temperature of the interior heated area must be 50° F (10° C) or higher. The freeze resistant package may be surface or recessed mounted. If recess mounted the surface of the cover must be flush with the interior wall surface. The package is furnished with screws for mounting the cover to the box. If the box is recess mounted, do not fasten the top and botto

Краткое содержание страницы № 8

EDFP210FP*B EDFP214FP*B EDFP217FP*B PARTS LIST ITEM NO. PART NO. DESCRIPTION 1 100322740560 GASKET 18 SEE FIG. 14 2 75570C SCREW-#10 X .50 PINNED TORX 3 15009C NIPPLE ASSY 4 27057C BRACKET-REGULATOR MOUNTING 5 27945C BRACKET-BASIN 6 27946C BRACKET-BASIN PIVOT 7 40045C HEX NUT 1-5/16 8 40206000 RETAINER SEE FIG. 13 9 98118C BUBBLER ASSEMBLY 10 45662C PUSH BUTTON 11 45663C SLEEVE-PUSH BUTTON GUIDE 12 50198C SNAP BUSHING 13 51667C BUMPER-REG. VALVE ASSY 14 55919C PUSH BUTTON (EXTENSION) 21