Краткое содержание страницы № 1
STUDIO
Conventional Flue
Instructions for Use,
Installation and Servicing
For use in GB, IE (Great Britain and Eire)
This appliance has been certified for use in countries other than those stated. To install this appliance in these countries, it is essential to obtain the
translated instructions and in some cases the appliance will require modification. Contact Gazco for further information.
IMPORTANT
Do not attempt to burn rubbish in this appliance. This appliance must only be operated with
Краткое содержание страницы № 2
COVERING THE FOLLOWING MODEL: STUDIO 1 CONVENTIONAL FLUE: 8700CFCHEC 8701CFCHEC P8700CFCHEC P8701CFCHEC PAGE APPLIANCE COMMISSIONING CHECkLIST 3 USER INSTRUCTIONS 4 INSTALLATION INSTRUCTIONS 8 Technical Specifications 8 Site Requirements 11 Installation 13 Commissioning 22 SERVICING INSTRUCTIONS 23 Fault Finding 23 How to replace parts 25 Basic spare parts list 31 Service Records 32 2
Краткое содержание страницы № 3
APPLIANCE COMMISSIONING CHECkLIST IMPORTANT NOTICE Explain the operation of the appliance to the end user, hand the completed instructions to them for safe keeping, as the information will be required when making any guaranteed claims. FLUE CHECk PASS FAIL 1. Flue is correct for appliance 2. Flue flow test 3. Spillage test GAS CHECk 1. Gas soundness & let by test 2. Standing pressure test mb 3. Appliance working pressure (on High Setting) mb NB All other gas appliances must be operatin
Краткое содержание страницы № 4
USER INSTRUCTIONS • regulate the flame from low to high and back 1. GENERAL • turn off the burner leaving just the pilot burning In ‘TEMP MODE’ you can: • set the room temperature so the thermostat in the 1.1 A competent person must carry out installation and remote automatically maintains that temperature servicing. In ‘TIMER MODE’ the stove: 1.2 In all correspondence, please quote the appliance type and • turns on and off accordin
Краткое содержание страницы № 5
USER INSTRUCTIONS Turning the Studio Off P2 only: • Press the Off button to extinguish the pilot • Press the SET button until TIMER mode is displayed 2.3 TEMP MODE • Hold the SET button until the display flashes the current time for P1 The display shows the current room temperature. • Press the SET button again to scroll past the settings for To increase or decrease the fire’s output: P1 and P1 • Press the SET button to select eit
Краткое содержание страницы № 6
USER INSTRUCTIONS EMERGENCY SHUT OFF 5 If the batteries fail during use of the fire, move the switch to the OFF (O) position, Diagram 3 (This switch is set to be ON during normal operation and must remain ON) 3 AR1860 • Support the frame and let it fall gently forward Emergency • Open it down to its stop position Shut Off When closing the window ensure the window catches are fully engaged. AR1961 4. CHANGING THE STUDIO BATTERIES The appliance batt
Краткое содержание страницы № 7
USER INSTRUCTIONS 5. ARRANGEMENT OF FUEL BED 11. HOT SURFACES 5.1 If you need to replace pebbles or refill the tray, make sure 11.1 Parts of this appliance become hot during normal use. the pebbles are flattened so they are level with the rim of • Regard all parts of the appliance as a ‘working surface’ the tray. • Provide a suitable fire guard to protect young children TAkE CARE NOT TO SPILL PEBBLES INTO THE PILOT and the infirm AREA ONLY PEBBLES SUPPLIED BY G
Краткое содержание страницы № 8
INSTALLATION INSTRUCTIONS TECHNICAL SPECIFICATION COVERING THE FOLLOWING MODELS: STUDIO 1 CF: STUDIO 2 CF: 8700CFCHEC 8701CFCHEC P8700CFCHEC P8701CFCHEC Model Gas CAT. Gas Type Working Aeration Injector Gas Rate Input kW (Gross) Country 3 Pressure m /h High Low Studio 1 12H Natural G20 20mbar 6 x 10 390 0.657 6.9 4.0 GB, IE CF Propane G31 37mbar 0.257 Studio 1 13+ Open both 185 6.9 4.0 GB, IE Butane G30 29mbar 0.197 CF sides Model Gas Gas Type Working Aeration Injector Gas Rate Input kW (Gross)
Краткое содержание страницы № 9
INSTALLATION INSTRUCTIONS TECHNICAL SPECIFICATION This appliance has been certified for use in countries other than those stated. To install this appliance in these countries, it is essential to obtain the translated instructions and in some cases the appliance will require modification. Contact Gazco for further information. PACkING CHECkLIST Qty Description Fixing kit containing:- 1 White Stone Chippings 1 x Instruction Manual 4 x Wood Screws 4 x Rawl Plugs 1 x Handset 4 x AA cell ba
Краткое содержание страницы № 10
INSTALLATION INSTRUCTIONS TECHNICAL SPECIFICATION 2 STEEL FRAME DIMENSIONS Steel Dimension Studio 1 Studio 2 A 1120 1350 B 675 675 C 646 846 D 320 320 E 177 177 F 237 237 G 25 25 PROFIL FRAME DIMENSIONS Profil Dimension Studio 1 Studio 2 A 846 1046 B 520 520 C 750 950 D 424 424 E 48 48 F 48 48 G 12.5 12.5 BAUHAUS FRAME DIMENSIONS Bauhaus Dimension Studio 1 Studio 2 A 860 1060 B 534 534 C 750 950 D 424 424 E 55 55 F 55 55 G 28 28 10
Краткое содержание страницы № 11
INSTALLATION INSTRUCTIONS SITE REQUIREMENTS • Slit with a sharp knife prior to passing the supply pipe through 1. FLUE AND CHIMNEY REQUIREMENTS 3.7 The gas supply must be installed in a way that does not restrict the removal of the appliance for servicing and WHEN INSTALLING A FLUE SYSTEM PLEASE REFER TO inspection. THE MANUFACTURER’S INSTRUCTIONS. The European chimney standards now describe chimneys and flues by their temperature, pressure and resistance to 4. VENTI
Краткое содержание страницы № 12
INSTALLATION INSTRUCTIONS SITE REQUIREMENTS 5.2 When the appliance is installed in a masonry chimney without a liner, there must be a minimum debris collection area, Diagram 1b 1b AR2006 5.3 DO NOT install onto a combustible wall; all combustible materials must be removed from the area shown in Diagram 1c. 1c 1160 not to scale 840 960 100 AR1226 5.4 A combustible shelf must be a minimum of 400mm above the top of the appliance. This is based on a 150mm deep shelf. For every extr
Краткое содержание страницы № 13
INSTALLATION INSTRUCTIONS INSTALLATION IMPORTANT: REFER TO DATA BADGE AND TECHNICAL 1 SPECIFICATION AT THE FRONT OF THE MANUAL TO ENSURE THE APPLIANCE IS CORRECTLY ADJUSTED FOR THE GAS TYPE AND CATEGORY APPLIED IN THE COUNTRY OF USE. FOR DETAILS OF CHANGING BETWEEN GAS TYPES REFER TO SECTION 10, SERVICING , ‘REPLACING PARTS’. 1. SAFETY PRECAUTIONS AR1010 1.1 For your own and other’s safety, you must install this appliance accord
Краткое содержание страницы № 14
INSTALLATION INSTRUCTIONS INSTALLATION 3 3.2 STUD WORk INSTALLATION METHOD 1 (FRAME) NOTE: With the legs fitted, this appliance can stand directly on the floor (normally in a false chimney breast), or without the legs on a protected platform at the required height, Diagram 5 5 AR1963 3. STUD WORk INSTALLATION THERE IS AN OPTIONAL DUCT kIT, CODE No. 8572 WHICH CAN BE FITTED AT THE SAME TIME AS THE APPLIANCE INSTALLATION. 3.1 Combustible parts of the stud work must be kept beyond AR1964 t
Краткое содержание страницы № 15
INSTALLATION INSTRUCTIONS INSTALLATION For non-combustible area see Diagram 2b. 7 The remaining area can be finished using plasterboard: • Apply a plaster finish to the front of the chimney breast • Secure the fire back to the stud work using four screws through flange, bracket, support bar • Decide on the position for the wall box containing the batteries and wall switch • Connect the wire from the fire to the battery pack, Diagram 10 1
Краткое содержание страницы № 16
INSTALLATION INSTRUCTIONS INSTALLATION This now determines the width of your two vertical stud 13 work supports. The kit has been designed so that 12mm thick plasterboard can be taken to the three channels, Diagram 16 16 wall plate AR1887 Because of the high temperatures this fire achieves, it is advisable to use marble slips or similar material between the appliance and the plasterboard Never use a one-piece slip as expansion (even cracking) AR1934 can occur. If a slip is used, longer
Краткое содержание страницы № 17
INSTALLATION INSTRUCTIONS INSTALLATION 20 18 AR1862 • Raise the door to almost upright and move the door left AR1911 This releases the left-hand side off its hinge pin • Lower the left-hand side of the door to clear the pin and The top of the chimney breast must have a minimum move the door to the right to release it from the right pin 2 200mm vent. The door is now free to remove, Diagram 21 • Apply a plaster finish to the chimney breast NOTE: Refer
Краткое содержание страницы № 18
INSTALLATION INSTRUCTIONS INSTALLATION 23 26 AR1965 AR1967 4.5 • Loosen the two screws retaining the plate beneath the burner • Move the box forward to release the rear off the studs The front of the plate can now be lifted off the screws: • Tilt the front edge of the box upwards and remove from the appliance • Pull it forward and remove, Diagram 24 4.8 METHOD 1 - FRAME 24 • Fit the four frame fixing brackets through the rear of
Краткое содержание страницы № 19
INSTALLATION INSTRUCTIONS INSTALLATION • Feed the wires for the remote touch pad through the 31 grommet in the left side of the loose box The wires are then fed inside the firebox and routed through the available access • Replace the loose box inside the main firebox ensuring the wires are not trapped • Replace the three wing nuts and seven screws • Connect the gas supply and check for leaks • Replace the rear panel ensuring the bottom edg
Краткое содержание страницы № 20
INSTALLATION INSTRUCTIONS INSTALLATION BOTH METHOD 1 OR 2 - MASONRY INSTALLATION 5.2 With the back panel held in place: • Place the bottom panel at the base of the fire 4.10 • Remove the compression elbow from the appliance and connect it to the gas supply pipe • Slide the side panels into position As the loose box is fitted into the main appliance: • Pass the elbow and supply pipe through the silicone 34 panel on the left side • Engage the
