Краткое содержание страницы № 1
DO NOT
DISCARD
Owner’s Manual
Installation and Operation
Model(s):
IDV4833IT, IDV4833ILT,
IDV4833IH, IDV4833ILH,
IDV6247IT, IDV6247ILT,
IDV6247IH, IDV6247ILH
CAUTION
DO NOT DISCARD THIS MANUAL
• Read, understand and follow • Leave this manual with
• Important operating and
these instructions for safe party responsible for
maintenance instructions
installation and operation. use and operation.
included.
WARNING WARNING
HOT SURFACES!
If the information in these instruc-
Glass and other surfac
Краткое содержание страницы № 2
Read this manual before installing or operating this appliance. Please retain this owner’s manual for future reference. This owner’s manual should be retained for future reference. A. Congratulations We suggest that you keep it with your other important Congratulations on selecting a Heatilator gas fi replace, an documents and product manuals. elegant and clean alternative to wood burning fi replaces. The information contained in this owner’s manual, unless The Heatilator gas fi replace you h
Краткое содержание страницы № 3
Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury. • WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury. • CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. • NOTICE: Used to address practices not related to personal injury. Table of Contents A. Congratulations 2 6 Termination Locations B. Warranty 5 A. Vent Termi
Краткое содержание страницы № 4
14 Appliance Setup A. Remove Shipping Materials 44 B. Remove Fixed Glass Assembly 44 C. Remove Materials Shipped Inside Firebox 44 D. Clean the Appliance 44 E. Accessories 44 F. Heat-Zone-Gas 44 G. Refractory 44 H. Install the Logs 45 I. Place Lava Rock and Rockwool 46 J. Glass Panel Assembly 47 K. Decorative Firescreen, Refractory Shields and Lower Decorative Front Face 48 L. Installing External Refractories 49 M. Air Shutter Setting 50 15 Troubleshooting A. Intellifi re Ignition System 51
Краткое содержание страницы № 5
B. Warranty Hearth & Home Technologies LIMITED WARRANTY Hearth & Home Technologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or Canada. Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts. Warranty Period HHT Manufactured Appliances and Venting Components Covered EPA Parts Labor
Краткое содержание страницы № 6
B. Limited Lifetime Warranty (continued) This limited warranty does not extend to or include surface fi nish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, fi rebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion on any of the metal surfaces, cast iron components, baffl es, fi repots, doors, or fi rebox area are not covered by this warranty. Noise resulting from minor expansion, contraction, or movement of certain part
Краткое содержание страницы № 7
Listing and Code Approvals 1 1 A. Appliance Certifi cation C. BTU Specifi cations ICON DV-Mesh IDV4833 IDV6247 MODELS: IPI LABORATORY: Underwriters Laboratories, Inc. (UL) Max/Min Input Rate (NG) 48,000/33,500 59,000/40,000 TYPE: Vented Gas Fireplace Heaters Orifi ce Size (NG) 0.128 0.144 STANDARD: ANSI Z21.88-2002•CSA2.33-M2002•UL307B Max/Min Input Rate (LP) 48,000/35,500 56,000/41,500 Orifi ce Size (LP) 0.079 0.086 This product is listed to ANSI standards for “Vented Gas Fireplace Heaters”
Краткое содержание страницы № 8
Inspection Note: The following requirements reference various The state or local gas inspector of the side wall horizon- Massachusetts and national codes not contained in this tally vented gas fueled equipment shall not approve the document. installation unless, upon inspection, the inspector ob- serves carbon monoxide detectors and signage installed H. Requirements for the Commonwealth of in accordance with the provisions of 248 CMR 5.08(2)(a)1 Massachusetts through 4. For all side wall
Краткое содержание страницы № 9
User Guide Operating Instructions 2 2 • Install a physical barrier such as: A. Gas Fireplace Safety - A decorative fi rescreen. - Adjustable safety gate. WARNING • Install a switch lock or a wall/remote control with child HOT SURFACES! protection lockout feature. Glass and other surfaces are hot • Keep remote controls out of reach of children. during operation and cool down. • Never leave children alone near a hot fi replace, whether Hot glass will cause burns. operating or cooling down. • D
Краткое содержание страницы № 10
C. Clear Space E. Fixed Glass Assembly See Section 14.J. WARNING! DO NOT place combustible objects in front of the fi replace or block louvers. High temperatures may start F. Remote Controls, Wall Controls and Wall a fi re. See Figure 2.2. Switches Avoid placing candles and other heat-sensitive objects on Follow the instructions supplied with the control installed mantel or hearth. Heat may damage these objects. to operate your fi replace: For safety: • Install a switch lock or a wall/remote c
Краткое содержание страницы № 11
H. Lighting Instructions (IPI) • For normal use, activate/deactivate your fi replace with the wall switch or remote control. • The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery life, remove them when using the transformer. • If your fi replace must be deactivated for service or an extended period of time, follow the instructions below. This appliance needs fresh air for safe operation and must be installed so there are p
Краткое содержание страницы № 12
I. After Fireplace is Lit Initial Break-in Procedure • The fireplace should be run three to four hours continuously on high. • Turn the fi replace off and allow it to completely cool. • Remove fi xed glass assembly. See Section 14.J. • Clean fi xed glass assembly. See Section 3. • Replace the fi xed glass assembly and run continuously on high an additional 12 hours. This cures the materials used to manufacture the fi re- place. NOTICE! Open windows for air circulation during fi replace break-in.
Краткое содержание страницы № 13
Maintenance and Service 3 3 Doors, Surrounds, Fronts Any safety screen or guard removed for servicing must be Frequency: Annually replaced prior to operating the fi replace. By: Homeowner When properly maintained, your fi replace will give you Tools needed: Protective gloves, stable work surface many years of trouble-free service. We recommend an- nual service by a qualifi ed service technician. • Assess condition of screen and replace as necessary. • Inspect for scratches, dents or ot
Краткое содержание страницы № 14
B. Maintenance Tasks-Qualifi ed Service Burner Ignition and Operation Technician Frequency: Annually The following tasks must be performed by a qualifi ed By: Qualifi ed Service Technician service technician. Tools needed: Protective gloves, vacuum cleaner, whisk Gasket Seal and Glass Assembly Inspection broom, fl ashlight, voltmeter, indexed drill bit set, and a manometer. Frequency: Annually • Verify burner is properly secured and aligned with pilot By: Qualifi ed Service Technician or ignite
Краткое содержание страницы № 15
Installer Guide Getting Started 4 4 A. Typical Appliance System NOTICE: Illustrations and photos refl ect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual Vertical Termination Cap (SECTION 10.H.) Noncombustible roof Storm Collar flashing maintains minimum (SECTION 10.F.) clearance around pipe (SECTION 10) Vent pipe penetrates roof, preferably without affecting roof rafters (SECTION 8) Ve
Краткое содержание страницы № 16
B. Design and Installation Considerations D. Inspect Appliance and Components Heatilator direct vent gas appliances are designed to op- • Carefully remove the appliance and components from erate with all combustion air siphoned from outside of the the packaging. Refer to Section 14.A. building and all exhaust gases expelled to the outside. No • The vent system components and decorative doors and additional outside air source is required. fronts may be shipped in separate packages. • If packa
Краткое содержание страницы № 17
Framing and Clearances 5 5 NOTICE: Illustrations refl ect typical installations and are A. Select Appliance Location FOR DESIGN PURPOSES ONLY. Illustrations/diagrams When selecting a location for the appliance it is important are not drawn to scale. Actual installation may vary due to to consider the required clearances to walls (see Figure individual design preference. 5.1). WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access. Due to h
Краткое содержание страницы № 18
To further prevent drafts, the wall shield and ceiling fi re- B. Construct the Appliance Chase stops should be caulked with high temperature caulk to A chase is a vertical box-like structure built to enclose the seal gaps. Gas line holes and other openings should be gas appliance and/or its vent system. In cooler climates caulked with high temp caulk or stuffed with unfaced insu- the vent should enclosed inside the chase. lation. If the appliance is being installed on a cement slab, a layer
Краткое содержание страницы № 19
D. Mantel and Wall Projections WARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as specifi ed. Framing or fi nishing material closer than the minimums listed must be construct- ed entirely of noncombustible materials (i.e., steel studs, concrete board, etc). Mantels 30 in. minimum to ceiling 18 17 16 22-3/4 15 22 14 21-1/4 13 20-1/2 12 19-3/4 11 19 10 18-1/4 9 17-1/2 8 16-3/4 7 16 6 15-1/4 5 14-1/2 4 13-3/4 3 13 2 12-1/4 1 11-1/2 10-3/4 10 Measured from top of firep
Краткое содержание страницы № 20
Termination Locations 6 6 A. Vent Termination Minimum Clearances WARNING AB 6in. (minimum)upto20in. 18 in. minimum Fire Risk. 152 mm/508 mm 457 mm 20 in. and over 0 in. minimum Maintain vent clearance to combustibles as specifi ed. Gas, Wood or Fuel Oil • DO NOT pack air space with insulation or other Termination Cap materials. Failure to keep insulation or other materials away from vent pipe may cause overheating and fi re. B Minimum Horizontal DV = 20 in. overhang (508 mm) A * BV = 8 ft (2
