Краткое содержание страницы № 1
DESIGNER SERIES
624BVSTNV/624BVSTNE, 624BVPFNV/624BVPFNE
624BVCLNV/624BVCLNE, 624BVCRNV/624BVCRNE,
624BVBYNV/624BVBYNE
B-VENT SPECIALTY GAS FIREPLACE SYSTEM
INSTALLATION, OPERATION AND MAINTENANCE MANUAL
WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION
MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR
ANY OTHER APPLIANCE.
WHAT TO DO IF YOU SM
Краткое содержание страницы № 2
"WARNING: IF NOT INSTALLED, OPERATED AND MAINTAINED IN ACCORDANCE WITH THE MANUFATURER’S INSTRUCTIONS, THIS PRODUCT COULD EXPOSE YOU TO SUBSTANCES IN FUEL OR FROM FUEL COMBUSTION WHICH CAN CAUSE DEATH OR SERIOUS ILLNESS AND WHICH ARE KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. ALSO, OPERATION, INSTALLATION AND SERVICING OF THIS PRODUCT COULD EXPOSE YOU TO AIRBORN PARTICLES OF GLASS WOOL FIBERS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER THRO
Краткое содержание страницы № 3
2 TABLE OF CONTENTS CONGRATULATIONS! You have chosen the finest decorative gas appliance available. Your 6-IN-1™ Specialty Gas Fireplace has been designed for years of heating and viewing enjoyment. Please take time to read this entire manual before installing or operating your system. Parts C22 Diagram...................................................................................................3 List.......................................................................................
Краткое содержание страницы № 4
ON N O C F F O PILOT 3 PARTS DIAGRAM 17 17 19 19 16 16 15 15 18 18 9 7 12 12 14 14 10 10 8 13 13 11 11 1 2 13 13 14 14 3 5 4 6 53D9019. Rev 3 11/07 PV PV MV MV TPTH TP TH OFF
Краткое содержание страницы № 5
4 PARTS LIST All repair part orders should be placed through your local dealer. To ensure prompt and accurate service, please provide the following information when placing a repair part order: Model num- ber of your Fireplace, Part Name, Part Number, and Quantity of parts needed. Technical Service Department 2813 W. Mall Drive, Unit B. Florence, Alabama 35630. Tel. - 1-866-500-5671 www.monessenhearth.com 6-IN-1 PART LIST KEY NO. KEY NO. QTY. QTY. PART NO. PART NO. PART NAME PART NAME 074270 0
Краткое содержание страницы № 6
5 APPLIANCE SYSTEM COMPONENTS The table below is a list of components which may be safely used with this product. Configuration Kits 6BK Bay Kit 6CK Corner Kit (works for left or right side) 6IK Island Kit 6PNK Peninsula Kit 6SK See-Thru Kit Control Kits 6CN Control Kit Natural Gas Standing Pilot 6CLP Control Kit Propane/LP Gas Standing Pilot 6CEN Control Kit Natural Gas Electronic Ignition Accessories GCKDV6E 6CEN LP Conversion Kit GCK6CLP 6CN LP Conversion Kit GCK6CN 6CLP Natural Conversion Ki
Краткое содержание страницы № 7
FIREPLACE CONFIGERATION INSTALLATION 6 PART 1 Remove front glass door by removing the cardboard fillers at the top and lifting up and away from the appliance. Install the handles onto the door using screws from the handle package. Keep front glass door off of the appliance until installation of Configuration Kit (Part 2) and Control Kit (Part 3) are completed. Remove carton containing logs. Retain for later installation. Remove and dispose of the cardboard support for log carton. Remove burner
Краткое содержание страницы № 8
FRAMING INSTRUCTIONS 7 It is best to frame your fireplace after it is positioned and the vent system installed. Use 2x4’s and frame to local building codes. To install the fireplace facing flush with the finished wall, position the framework to accommodate the thickness of the finished wall. It is not necessary to install a hearth extension with this fireplace system. The junction box should be wired to the electrical system at the time of installation of the fireplace. Wiring must be performed
Краткое содержание страницы № 9
FIREPLACE INSTALLATION 8 To accommodate the various configurations, we have provided access openings in the bottom of the unit for gas line and wall switch wires. This may not be convenient for some installations, if so you may drill an access opening into the lower face of the unit (1" for gas line, 1/2" for the grommet). 1. Route the 3/8 inch N.P.T. black iron gas line or equivalent to the fireplace. Include a manual shut-off valve and union in the line so the control may be disconnected fo
Краткое содержание страницы № 10
9 FIREPLACE INSTALLATION AND VENTING FIGURE 5FIGURE 6 APPROVED COWL ATTACH 6" "B" VENT PIPE TO ATTACH 6" "B" VENT PIPE TO TRANSITION USING (4) SHEET TRANSITION USING (4) SHEET METAL SCREWS. METAL SCREWS. STORM COLLAR FLASHING 6" TYPE "B" GAS VENT 7 FT. 7 FT. ATTACH TRANSITION TO FLUE COLLAR ATTACH TRANSITION TO FLUE COLLAR MIN. USING (3) SHEET METAL SCREWS. USING (3) SHEET METAL SCREWS. LISTED CEILING MINIMUM CLEARANCE AS SUPPORT SPECIFIED BY VENT MANUFACTURER. "B" VENT CLEARANCE AS SPECIFIED
Краткое содержание страницы № 11
VENTING REQUIREMENTS 10 WARNING: DO NOT CONNECT THIS APPLIANCE TO A CHIMNEY FLUE SERVING A SEPARATE SOLID FUEL BURNING APPLIANCE. CARBON DEPOSITS (SOOT) AND CREOSOTE FROM SOLID FUELS CAN CLOG THE VENT FROM THE APPLIANCE CAUSING POISONOUS CARBON MONOXIDE TO BE RELEASED INTO THE ROOM IN WHICH THE APPLIANCE IS INSTALLED. All vented gas-fired appliances when operating correctly produce small concentrations of carbon monoxide along with other combustion products. Should something interfere with the
Краткое содержание страницы № 12
LOG INSTALLATION 11 Position logs and twigs onto burner as shown in Figure 8. FIGURE 8 TOP VIEW OF TOP VIEW OF LOGS AND TWIGS. LOGS AND TWIGS. Apply ember material near the grate bars as shown in Figure 9. FIGURE 9 TOP VIEW - FRONT LOG AND GRATE BARS TOP VIEW - FRONT LOG AND GRATE BARS SPECIAL EMBER MATERIAL PROVIDED MAY BE PLACED BETWEEN FRONT SPECIAL EMBER MATERIAL PROVIDED MAY BE PLACED BETWEEN FRONT TYPICAL BOTH SIDES PORTING AND GRATE BARS WITH A RECOMMENDED 3/8" SPACING FREE PORTING AND GR
Краткое содержание страницы № 13
O L I P F F PV PV PV PV MV MV MV MV TP TH TP TH O WALL SWITCH INSTALLATION 12 Units with 6CEN Controls FIGURE 10 GAS CONTROL/ELECTRONIC IGNITION ROUTING GAS CONTROL/ELECTRONIC IGNITION ROUTING 1. Determine a convenient location within PILOT twenty (20) feet and cut a hole large PILOT BURNER WIRE TYPE 105 WIRE TYPE 105 GROUND DEGREE C. REPLACE DEGREE C. REPLACE GAS CONTROL VALVE enough to accommodate the wall WITH SAME OR WITH SAME OR PILOT GAS EQUIVALENT. EQUIVALENT. SUPPLY switch yet be cover
Краткое содержание страницы № 14
ADJUSTMENTS AND MAINTENANCE 13 Pilot Burner Adjustment 1. Adjust the pilot screw to provide a properly sized flame. 2. Do not adjust the pilot screw all the way out counterclockwise because it will leak gas. Flame Switch (For Units with 6CN and 6CLP Controls) FIGURE 12 Your fireplace has been equipped with a thermocouple which senses the flame and shuts of the gas flow to the pilot and main burner in the event that the pilot flame is unstable or becomes extinguished. DANGER: BYPASSING THE THE
Краткое содержание страницы № 15
ADJUSTMENTS AND MAINTENANCE 14 Maintenance of the Appliance Air flowing through the appliance will cause dust and lint to collect on the grate, burner and logs. Exessive buildup of dust and lint can cause the pilot and burner to operate improperly and produce hazardous levels of carbon monoxide, a poisonous gas. The appliance may produce carbon (soot) during operation. This carbon (soot) may collect on some logs, some areas of the grate and on the fireplace and vent. Slight carbon buildup is a
Краткое содержание страницы № 16
COMBUSTION AIR PRECAUTIONS 15 NOTE: The use of outside air for combustion is optional unless required by building codes. It is only necessary to supply outside combustion air to one side of the fireplace. Use the model OAC4 combustion air kit. 1. Extremely long runs and numerous turns in the duct leading from the fireplace to the combustion air assembly should be avoided. These conditions will increase the resistance to the free flow of air through the duct. Refer to Figure 9 for methods of
Краткое содержание страницы № 17
COMBUSTION AIR ASSEMBLY 16 MODEL AK4 COMBUSTION AIR ASSEMBLY 1. Remove the cover plate from the 4-inch outlet opening location on the left outside of the fireplace. DO NOT remove the cover if the outside air will not be connected. 2. Place the starting collar (4 inch) into the hole on the left side of the fireplace. Fasten it in place with the four sheet metal screws provided. 3. Cut a 6-inch diameter opening for model AK4 in the outside wall covering where the outside vent is to be located. 4
Краткое содержание страницы № 18
OPERATING INSTRUCTIONS 17 FOR UNITS WITH 6CEN CONTROLS INSTALLED FOR YOUR SAFETY READ BEFORE LIGHTING FOR YOUR SAFETY READ BEFORE LIGHTING IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT WARNING: CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. A. THIS APPLIANCE IS EQUIPPED WITH AN IGNITION IF YOU CANNOT REACH YOUR G
Краткое содержание страницы № 19
OFF OPERATING INSTRUCTIONS 18 FOR UNITS WITH 6CN AND 6CLP CONTROLS INSTALLED FOR YOUR SAFETY READ BEFORE LIGHTING IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT WARNING: CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALL IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALL A. A. THIS AP
Краткое содержание страницы № 20
SAFETY CHECKLIST 19 Correct installation and safe operation of this appliance require, but are not limited to the following: Do's: 1. Do use this appliance only on type of gas it is designed, certified and equipped. 2. Do install this appliance and all gas piping according to local codes, or in the absence of local codes, according to the current National Fuel Gas Code, ANSI Z223.1 latest edition. 3. Do disconnect or isolate the appliance during supply line pressure testing. 4. Do locat
