Краткое содержание страницы № 1
SAVE THESE INSTRUCTIONS.
Owner's Manual
Installation and Operation
Model:
P35i
Pellet/Biomass
Fireplace Insert
#1-70-774195
#1-70-774235
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating and
• Read, understand and • Leave this manual with
maintenance instructions
follow these instructions party responsible for use
included.
for safe installation and and operation.
operation.
WARNING
WARNING
Please read this entire manual
HOT SURFACES!
before i
Краткое содержание страницы № 2
P35i Fireplace Insert Hearth & Home Technologies welcomes you to our tradition of excellence! By choosing a Harman appliance, you have become part of a long standing family committed to meeting the heating needs of consumers with the most distinctive, powerful and responsible home heating products available. The P35i insert has brilliant features in an elegant package, giving you 0 to 35,000 BTU when you need it, automatically. Aside from the regular, simple cleaning
Краткое содержание страницы № 3
P35i Fireplace Insert Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury. • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury. • CAUTION! Indicates a hazardous situation which, if not avoided could result in minor or moderate injury. • NOTICE: Indicates practices which may cause damage to the appliance or to property. TABLE OF CONTENTS Section 1: Listing and Code Approv
Краткое содержание страницы № 4
P35i Fireplace Insert Listing and Code Approvals 1 A. Appliance Certification E. BTU & Efficiency Specifications Model: P35i Insert Particulate Emissions Exempt from EPA per Laboratory: OMNI-Test Laboratories, Inc. Rating: 40 CFR, Method 28A Report No. 135-S-25-6.2 0 or 6,000 - 35,000 / hr *BTU Input: Type: Solid Fuel Room Heater / Fireplace Heating Capacity: 1,500 sq. ft. Insert. Hopper Capacity- Standard(s): ASTM E15
Краткое содержание страницы № 5
P35i Fireplace Insert Special Warnings and Notes 2 Carbon monoxide, referred to as CO, is a colorless, CO detectors are very sensitive and may sound an odorless gas that is produced during combustion of solid alarm for fumes other than CO or CO from sources other fuels. CO is toxic and can be fatal. than the stove such as a car or lawn mower exhaust. If the alarm sounds Even though this stove is designed to be as safe 1. Increase house ventilation by opening windows or as possible, it is r
Краткое содержание страницы № 6
P35i Fireplace Insert Getting Started 3 A. Design, Installation & Location B. Fire Safety Considerations Maintain the designated clearances to combustibles. 1. Appliance Location Insulation must not touch the chimney. You must Consideration must be given to safety, convenience, maintain the designated air space around the chim- traffic flow, and the fact that the appliance will need to ney. This space around a chimney is necessary to be vented to the outside. This
Краткое содержание страницы № 7
P35i Fireplace Insert C. Component Locations Hopper Lid Latch Viewing Glass Ash Pan Cover Door Latch Control Panel Return Air Slots Do Not allow finish materials to block the air flow through the return air slots. Combustion Blower Exhaust Sensing Probe (ESP) Pellet Pro Feeder Feed Motor Distribution Blower Ash Pan Latch Frame Latch 7 Save These Instructions 3-90-775 Pellets or
Краткое содержание страницы № 8
P35i Fireplace Insert D. Pre- Use Check List 1. Place the appliance in a location near the final installation and follow the procedures WARNING below: Inspect appliance and components for 2. Open the appliance and remove all articles damage. Damaged parts may impair safe packed inside. Inspect all items for shipping operation. damage. Notify dealer of any missing or • Do NOT install damaged components. damaged goods. • Do NOT install incomplete components. 3. All
Краткое содержание страницы № 9
P35i Fireplace Insert Dimensions & Clearances 4 A. Appliance Dimensions A B 24” 60.96 cm Standard Surround Oversize Surround # 1-00-774221 # 1-00-774250 A: 40" (101.6 cm) 46" (116.8 cm) B: 31" (78.74 cm) 34" (86.36 cm) 22” 55.88 cm 14” 35.56 cm 2” 5.08 cm 8” 10” 20.32 cm 25.4 cm 9 Save These Instructions 3-90-775 Pellets or Corn/Pellet Mixture Only 19.5” 49.53
Краткое содержание страницы № 10
P35i Fireplace Insert D. Minimum Opening for Masonry B. Clearances To Combustibles - and Manufactured Fireplaces Masonry or Manufactured Fireplace ThE ClEARANCEs spECIfIED ARE fOR yOUR sAfETy! ThEsE ClEARANCEs mA y ONl y bE REDUCED by mEANs AppROvED by ThE REGUlA T OR y AUThORITy . I H Mantel Face Trim G B D Inches Millimeters Location A C Minimum Width 24 609 G Minimum Depth 14.5 368 H Minimum Height #1-70-774235 23½
Краткое содержание страницы № 11
P35i Fireplace Insert F. Factory-Built Fireplace Installation The factory built chimney must be listed per UL 127 (US) and meet type HT requirements of UL 103 (US). Factory When installing the P35i Insert into a factory built Built fireplace chimneys tested to UL 127-98 may be, at the wood burning fireplace, several things need to be taken fireplace manufacturers option, tested to the same criteria into consideration. as UL 103HT requirements. If the chimney is not listed as The size o
Краткое содержание страницы № 12
P35i Fireplace Insert Chimney connector shall not pass through an attic or roof space, closet or similar concealed space, or a floor or ceiling. Vent Information 5 A. Vent Termination Requirements = Vent Termination = Air Supply Inlet = Restricted Area WARNING: Venting terminals must not be recessed into I. The clearance to service regulator vent outlet must be 1 a wall or siding. a minimum of 6 feet. NOTE: Only PL or L vent pipe wall pass-throughs and J. The clea
Краткое содержание страницы № 13
P35i Fireplace Insert B. Avoiding Smoke and Odors Negative Pressure, Shut-down, and Power Vent Configurations: To reduce probability of reverse drafting during Failure: To reduce the probability of back-drafting or burn- shut-down conditions, Hearth & Home Technologies back in the pellet burning appliance during power strongly recommends: failure or shut-down conditions, the stove must • Installing the pellet vent with a minimum vertical be able to draft naturally without exhaust blower o
Краткое содержание страницы № 14
P35i Fireplace Insert C. Venting Requirements and Use only the specified venting components. Use of any other components will void the product Restrictions warranty and may pose a hazard. A combustion blower is used to extract the combus- tion gases from the firebox. This causes a negative pres- Do Not Install A Flue Damper In The Exhaust sure in the firebox and a positive pressure in the venting Venting System Of This Appliance. system. The longer the vent pipe and
Краткое содержание страницы № 15
P35i Fireplace Insert Be sure to design the venting so that it can be easily D. Existing Fireplace Installation: cleaned. If using a short run of venting, whether flex or rigid, Check with your local authority having jurisdiction to through the damper and into the chimney flue; The determine if this venting method is acceptable. Some Damper must be removed or locked in the open posi- Provincial, State, or Local codes may require a full tion and sealed with a plate constructed of steel o
Краткое содержание страницы № 16
P35i Fireplace Insert The top of the chimney must also be sealed. Otherwise, it can become a nesting area or a E. Existing Fireplace, Rear Vent: water trap. NOTE: When installed in a rear vent configuration, the maximum BTU may be reduced due to elevated ESP temperatures associated with the horizontal exhaust stream. If passing through combustible material, the proper thimble from the vent manufacturer must be used. F. Optional Zero Clearance Cabinet Inst
Краткое содержание страницы № 17
P35i Fireplace Insert Mobile Home 6 A. Mobile Home Installation CAUTION Maintain structural integrity of mobile home: Outside Air Kit #1-00-774280 Must be used • Floor, wall, ceiling and/or roof. for installation in a mobile home. Do NOT cut through: • Floor joist, wall studs, or ceiling trusses. 1. An outside air inlet must be provided for combus- • Any supporting material that would affect the tion air, and must remain clear of leaves, debris, structural integrity. ice, and/or snow. The o
Краткое содержание страницы № 18
P35i Fireplace Insert Appliance Set-Up 7 The image at left shows the use of the chim- A. Outside Air Attachment ney for outside air supply. Also shown is the Chimney intake extension on the top of the chimney. It is slotted to allow fresh air into Outside Air Kit #1-00-774280 (sold separately) must the flue. Be sure to use the proper flashing be used for attaching outside air to the insert. This kit and vent cap to prevent rain from entering the chimney flue. con
Краткое содержание страницы № 19
P35i Fireplace Insert B. Installing the Surround The surround consists of three panels, the top and two sides. Follow these steps for installation: 1. Remove the insert body from the mounting frame; 2. Start your leveling bolts into the floor of the frame and adjust to slightly raise the height.(see next section) This will allow some clearance to assemble the surround. 3. Prepare the side panels by removing three nuts each. The left side
Краткое содержание страницы № 20
P35i Fireplace Insert D. Securing the Mounting Frame The mounting frame is the anchor for the appli- ance. If the frame is not secured properly, shifting E. Attaching the Venting will occur when sliding the insert in or out. There are four (4) holes located as shown, that are threaded for 5/16 - 18 bolts. Thread the bolts down through the holes to raise the frame corners as needed, to level. NOTE: When installed in a rear vent configuration, the maximum BTU may b
