Краткое содержание страницы № 1
SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
EG40 BV
B Y : S H E R W O O D I N D U S T R I E S L T D
OWNER’S MANUAL
WHAT TO DO IF YOU SMELL GAS
• Open windows/Extinguish any open flame.
• Do not try to light any appliance.
• Do not touch any electrical switch or use any phone in your
building.
• Immediately call your gas supplier from a neighbour’s phone.
Follow the gas supplier’s in
Краткое содержание страницы № 2
Safety Precautions FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION: • All ENVIRO gas-fired appliances must be installed • To prevent injury, if the pilot or pilot and in accordance with their instructions. Carefully read all burners have gone out on their own, open the the instructions in this manual first. Consult the building glass door and wait 5 minutes to air out before authority having jurisdiction to determine the need for a
Краткое содержание страницы № 3
Table of Contents Safety Precautions..........................................................................................2 Table of Contents...........................................................................................3 Codes And Approvals......................................................................................4 Specifications.................................................................................................5 Dimensions................................
Краткое содержание страницы № 4
Codes And Approvals BV: This Vented appliance draws all of its combustion air from the dwelling and must be vented using listed B or L vent. May also be vented through a conventional chimney using a chimney liner kit. This appliance has been tested and approved for installations from 0 feet to 2000 feet (610 m) above sea level. In the USA: The appliance may be installed at higher altitudes. Please refer to your American Gas Association guidelines which state: the sea level rated input of Gas
Краткое содержание страницы № 5
Specifications WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death. DIMENSIONS: � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �� � � � � � � � � � � � Figure 1: EG40 Exterior Dimensions. CLEARANCES TO COMBUSTIBLES: A. Sidewall to unit 12 inches (30.5 cm) B. Backwall to unit 4 inches (10.2 cm) � � C. Corner to unit 2 inches
Краткое содержание страницы № 6
Initial Installation QUALIFIED INSTALLERS ONLY VENTING: This model must have a vent opening in the rear of the unit. Confirm this and also check that the label on the right side panel door states “Vented Room Heater”. WARNING: This appliance has been designed to operate by drawing combustion air and dilution air from the room. The draft hood located in the same atmospheric pressure zone as the combustion air inlet to the appliance. It is also designed to draw room air for proper heat circu
Краткое содержание страницы № 7
Initial Installation QUALIFIED INSTALLERS ONLY TERMINATION: � � � � � � � � � � � � The bottom of the vent cap shall extend at � � � � � � � � � � � � � � � least 2 feet (0.61 m) above the highest point � � � � � � � � � � � � � � � � � of the roof where it passes through and at � � � � � � � � � � � � � � � � � � � � � � least 2 feet (0.61 m) higher than any portion � � � � � � � of the roof within a horizontal distance of 10 � � � � � � � � � � feet (3.1 m). � � � � � � � See vent manufa
Краткое содержание страницы № 8
Initial Installation QUALIFIED INSTALLERS ONLY STRAIGHT VERTICAL INSTALLATION: This basic venting configuration shown are rough guidelines only. Follow national and local codes for other installation options. For the best venting performance, we recommend a total vent height in the range of 10 feet (3.0 m) to 30 feet (9.1 m). The total horizontal length depends on the number of elbows used; a 90° elbow accounts for 5 feet (1.5 m) of the horizontal run. The venting should never slope down,
Краткое содержание страницы № 9
Initial Installation QUALIFIED INSTALLERS ONLY ELECTRICAL REQUIREMENTS: The ENVIRO EG40 will operate without electrical power. This model has a millivolt gas control, which uses the pilot flame to generate enough electricity to operate the main burners. The appliance is equipped with a blower and must be electrically connected and grounded in accordance with local codes or in the absence of local codes, with the current CSA C22.1 CANADIAN ELECTRICAL CODE Part 1, SAFETY STANDARDS FOR ELECTRICA
Краткое содержание страницы № 10
Initial Installation REPLACING THE BLOWER: 1. Turn the unit off and remove the log set. 2. Remove the brick liner. 3. Remove the burner tray assembly by removing the screw on either side of the tray, between the front and rear burners. Lift the tray out. 5 4. Remove the four (4) /16” bolts that hold the blower mounting plate to the back firewall. Use a light lubricating oil on screws before removal. 5. Carefully pull the blower assembly into the firebox (see Figure 8) disconnect the blowe
Краткое содержание страницы № 11
Initial Installation FUEL CONVERSION: WARNING: This conversion kit shall be installed by a qualified service technician in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion or CO poisoning may result. The qualified service agency is responsible for the proper installation of this kit. The installation is not proper or complete u
Краткое содержание страницы № 12
L O I P T O L T P T H T P T H I P F F Initial Installation GAS LINE CONNECTION AND TESTING: WARNING: Only persons licensed to work with gas piping may make the necessary gas connections to this appliance. GAS LINE CONNECTION • This stove is equipped with a certified flexible pipe located on the right side of the unit terminating in a 3⁄8” male NPT fitting. Consult your local authorities codes or the CAN/CGA B 149 (1 or 2) installation code in Canada, or in the USA gas installations follow e
Краткое содержание страницы № 13
Secondary Installation INSTALLATION OF LOG SET AND EMBERS: The placement of the logs is not arbitrary. If they are positioned incorrectly, the flames can be “pinched” and will not burn correctly. The burner come with five (5) locator pins, and the rear log has one (1) ledge, which make alignment easier. Using the pictures provided, carefully set the logs in place. NOTE: The logs are fragile and should be handled gently. CAUTION: Use only the type of ember material supplied with this applianc
Краткое содержание страницы № 14
Secondary Installation L e d g e f o r R i g h t L o g 4. Upon the first light up, watch for ignition to ALL burner ports. If a long delay is noted: First, wait for the appliance to cool down. • Open the front door of the appliance. • Check to carefully reposition the embers making sure that burner ports are not P i n f o r R i g h t L o g plugged solid or blocked. Important note: When the unit is turned on for the first time, It should be turned Figure 14: Step 4 of Log Placement. onto
Краткое содержание страницы № 15
Operating Instructions FOR YOUR SAFETY READ COMPLETELY BEFORE OPERATING. WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OR LIFE. A) This appliance is equipped with a pilot that must be lit by hand by following these instructions exactly. B) BEFORE LIGHTING smell all around the appliance area for gas, and next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YO
Краткое содержание страницы № 16
Routine Maintenance and Service Annually check to ensure that your Venting system is clear. Periodically check the pilot and burner. Check to see that all the burner ports are clean and clear. Check the pilot head for blockage. Check to ensure the pilot flame is blue with no or very small yellow tips. OPENING THE DOOR Turn unit off and wait until the appliance has cooled down. 1. Open the right hand hinged side flap, which will expose a door � � � � � � � � � � � � � � � � � � � � fastener.
Краткое содержание страницы № 17
Trouble Shooting Problem Possible Cause Solution Spark will not light the Defective piezo ignitor. • Check connections to ignitor. pilot after repeatedly • If ignitor connections are good but there is no spark; pressing the spark ignitor replace ignitor. Broken spark electrode. • Check for broken ceramic insulation. • Replace electrode if broken. Misaligned spark electrode. • If spark is not arcing from electrode to pilot - adjust by loosening the screws on the pilot base. Adjust away from bu
Краткое содержание страницы № 18
Parts List Reference Part Description Part Number Number 1 120 °F (49 °C) Ceramic Temperature Sensor EC-001 2 220 °F (104 °C) Ceramic Spill Switch EC-002 3 S.I.T. NOVA Valve NG (50% turn down) EC-006 3 S.I.T. NOVA Valve LP (50% turn down) EC-007 4 Thermocouple EC-009 4 Spark Electrode with Ignitor Cable EC-011 4 Thermopile EC-012 4 Fully Assembled Pilot NG EC-015 4 Fully Assembled Pilot LP EC-016 4 Pilot Orifice NG Threaded EC-019 4 Pilot Orifice LP Threaded EC-020 Pilot Gasket EC-021 5 S.I.T
Краткое содержание страницы № 19
Parts List Reference Part Description Part Number Number BV Owner’s Manual EG40-071 14 Pedestal EG40-080 15 Side Panel EG40-086 16 BV Stove Top EG40-087 Firebox Baffle EG40-088 Stove Top Baffle BV EG40-091 Venturi Cover Plate EG40-097 17 Front Venturi EG40-098 18 Bar Set - Painted (3 pieces) EG40-114 18 Bar Set - Gold (3 pieces) EG40-115 18 Bar Set - Nickel (3 pieces) 50-478 Burner Gasket EG40-120 Steel Brick Liner EG40-129 Brick Liner Backing EG40-130 19 Pedestal Door EG40-135 LP to NG Convers
Краткое содержание страницы № 20
Parts Diagram - Chassis � � � � � � � � � � � � � � � � � � � � � � � E G 4 0 B o d y ( C h a s s is ) Ju l y 2 004 20
