Краткое содержание страницы № 1
™
BRESCIA (GALLERY EDITION)
OWNER’S MANUAL
21
Краткое содержание страницы № 2
CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PREPARATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FAN INSTALLATION . . . . . . . . . . . . . . . .
Краткое содержание страницы № 3
MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mount- ing recommendations as you decide where to install your Casablanca fan. • For safety reasons, the fan blades must be a minimum of 7′ above the floor. • Do not locate th
Краткое содержание страницы № 4
BRESCIA (GALLERY EDITION) PREPARATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. PERMA LOCK™ HARDWARE • ALLEN SET SCREW DOWNROD & BALL 1 1 ⁄4-20 x ⁄4" ASSEMBLY 3mm (PRE-INSTALLED) ALLEN WRENCH FAN PREPARATION IMPORTANT SAFETY INFORMATION! MOTOR BEFORE STARTING THE INSTALLATION OF YOUR CEILING FA
Краткое содержание страницы № 5
CROSSBAR MOUNTING BRACKET INSTALLATION CEILING FAN Proceed with installation as follows: APPROVED Step 1. Route the wires from the ceiling outlet box through OUTLET BOX the crossbar mounting bracket center hole. Attach the bracket, with ground wire and ridges down, to the ceiling fixture out- let box with the mounting hardware included with the outlet box. RIDGE Tighten the screws firmly by hand only, being careful not to CEILING SIDE bend the bracket by over tightening. WIRING DOWN CAUTION: To
Краткое содержание страницы № 6
BRESCIA (GALLERY EDITION) HANGING THE FAN Step 3. To hang the fan body in the canopy, hold the fan body firmly and in- sert the ball into the canopy opening. Check that no wires were pinched. Ro- tate the fan body until the slot in the ball fits into the pin opposite the canopy opening. BALL Fan Hanging Weight is 26 lbs SLOT PIN CANOPY ELECTRICAL CONNECTIONS Step 4a. Attach the fan wires to the ceiling fixture outlet box wiring by placing the bare ends of the wires side by side WIRE NUT and then
Краткое содержание страницы № 7
INSTALLING THE BLADE/BLADE HOLDER TO FAN MOTOR PREPARATION Step 8. To reach the blade holder mounting holes in the fan motor the dummy switch housing must be removed. 9 Take out the two 5-32 X /32” screws secur- ing the dummy switch housing and remove. Set the two (2) screws aside for the mo- ment, they will be used in Step 12 to install the switch housing after the blades are in- stalled. The dummy switch housing is used only when shipping the fan. DUMMY SWITCH HOUSING Note: Save these two scre
Краткое содержание страницы № 8
BRESCIA (GALLERY EDITION) REMOVE SHIPPING BLOCKS Step 10. On the flywheel remove the four SHIPPING shipping blocks by unscrewing the screws. BLOCKS Discard the shipping blocks and shipping block screws. BLADE/BLADE HOLDER INSTALLATION Step 11. Using the screws from the pack, attach each blade/blade holder assembly to the motor. Using the screwdriver, tighten securely by hand only. BLADE HOLDER Your Brescia fan is equipped with a fly- SCREWS wheel that allows for both 4 and 5 blade installation.
Краткое содержание страницы № 9
INSTALL SWITCH HOUSING ASSEMBLY TO LIGHT FIXTURE Step 14. Thread the wires from the light fixture through the center hole of the switch housing as- sembly. Then attach the ceiling fan wires to the light fixture wires by placing the bare ends of the wires together and securing with a wire nut. Connect in this order: • White wire from fan to white wire of light fixture. WIRES & Secure with wire nut. WIRE NUTS SWITCH • Black wire from fan to black wire of light fixture. HOUSING Secure with wire nu
Краткое содержание страницы № 10
BRESCIA (GALLERY EDITION) LIGHT FIXTURE GLASS INSTALLATION Step 17. Carefully slide the glass into the light kit as shown. GLASS LIGHT KIT GLASS ATTACH LIGHT KIT TO FAN Step 18. Lift the light fixture to the switch housing, run- ning the cap screws through the key holes. CAUTION! Make sure you feed extra wire from the light fixture through the center hole of the switch housing to avoid pinched wires. Turn the light fixture left (counter-clockwise) to engage the screws in the key holes. TIGHTEN
Краткое содержание страницы № 11
NO LIGHT KIT INSTALLATION NOTE: THE FOLLOWING STEPS ARE TO BE PERFORMED ONLY IF YOU ARE NOT SWITCH INSTALLING THE LIGHT KIT! HOUSING Step A1. Locate the switch housing/cap 3 assembly and remove the two 8-32 X /8″ CAP screws holding the cap onto the switch housing. CAP SCREW Note: Save these two screws–they 3 8-32 X /8″ will be used in Step A5! (2) INSTALLING THE SWITCH HOUSING ASSEMBLY 9 Step A2. Attach the two (2) 5-32 X /32″ switch housing screws removed in Step 8 (on Page 6) to fan motor as
Краткое содержание страницы № 12
R INTELITOUCH© INSTALLING THE W-32 WALL CONTROL The wall control installs in the same manner as an ordinary light switch, using an existing junction box and wiring. This controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason the following precautions must be observed: 1. Use only the Casablanca W-32 wall control. 3. Do not use more than one fan per wall control. 2. Do not use any additional control with your Inteli-Touch 4. No othe
Краткое содержание страницы № 13
R INTELI•TOUCH OPERATION POWER The button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunderstorms. It is also used to exit or enter additional programs. POWER must be left on to retain a previously set fan speed or light level. INTELI•TOUCH OPERATION SPEED CONTROL There are six individual speed settings for the fan; each speed is indicated by an audible tone of increasing pitch. FAN CONTROL To select the desired fan speed:
Краткое содержание страницы № 14
R ® INTELI•TOUCH OPERATION LIGHT-MINDER PROGRAM The Light-Minder program automatically turns OFF the fan mounted lights after two hours. To enter the Light-Minder Program: 1. Turn the OFF for at least three seconds. 2. Turn the ON. 3. Immediately operate the buttons in the following sequence: + + + + + + 4. A series of tones indicates this command has been accepted. The fan and light will operate normally using the buttons to turn them on and off. But, if the lights are left on, they wil
Краткое содержание страницы № 15
R TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes: For cleaning, a soft brush or lint-free cloth Never Lubricate this Fan! should be used to prevent scratching the finish. A vacuum cleaner The precision motor at the heart of your Casablanca fan features brush nozzle can remove heavier dust. Surface smudges or an accu- sealed bearings that are lubricated for life. Do not attempt to oil mulation o
Краткое содержание страницы № 16
R W-21 MOUNTING PARTS WALL BRACKET ANCHOR (4) ‘AAA’ ALKALINE WALL BRACKET BATTERY (3) REMOTE CONTROL REMOTE CONTROL SCREW (4) W-21 WALL BRACKET WALL BRACKET INSTALLATION Installation of Remote Control Mount control in convenient location The wall mounting bracket for the remote control should be WALL located in a position that is approximately eye level. Secure 1 MOUNTING the wall mounting bracket with the 1 /4″ screws or anchors BRACKET provided, making sure it is level with the floor. CAUTION!
Краткое содержание страницы № 17
R IMPORTANT OPERATING NOTES Turning On Your Fan: The fan will not receive any signals Labeling: If you have more than for the first 20 seconds after power on. This allows the one Comfort•Touch fan in your electronics to warm up and stabilize. home, we suggest you put an ad- hesive room identification label Power Failure: The remote control is not affected by house- on the back of the control. La- hold power failure as it is battery operated. Once power is bels are in the remote control restor
Краткое содержание страницы № 18
R REVERSE FEATURE Pressing the button will change the direction of rotation. An audio tone signals the beginning of the reverse sequence and you will see the airflow direction arrow changing. The fan gradually slows to a stop, then reverses direction. Note: This function does not operate if the fan is not running. REVERSE AUTO-SPEED FEATURE In the Auto Speed mode, fan speed changes in response to changes in room tempera- ture. Push the button to start. The words 'AUTO SPEED' show on the displa
Краткое содержание страницы № 19
R COMFORT•TOUCH CHANGING CHANNELS - CONTROL Changing the control channel 1. Hold the button down until a tone is heard. 2. The temperature display will show the current channel number. 3. Press fan up or down buttons to change the number to a REMOTE unique number from 49 to 63. CONTROL DO NOT use other channel numbers. CHANNEL 4. Push to return to normal operation. NUMBER You will need to repeat this step any time you remove the remote Note: Always change the remote control channel contro
Краткое содержание страницы № 20
R TROUBLESHOOTING PROBLEM COMFORT•TOUCH POSSIBLE REMEDIES.. FAN O.K., NO LIGHT Check for burned-out light bulb. Check fan light wires. REMOTE CONTROL OF FAN IS ERRATIC Check batteries installed correctly. Install fresh ALKALINE batteries. SELECTING WINTER MODE CANCELS AUTO-SPEED Normal. CHANGING SPEED OR DIRECTION CANCELS WINTER Normal. FAN APPEARS TO RESPOND TO UNKNOWN SIGNAL Change channel of control and fan to a number between 49 and 63. CONTROL ALSO OPERATES A SECOND FAN IN HOME Change cha
