Краткое содержание страницы № 1
Краткое содержание страницы № 2
CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PREPARATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FAN INSTALLATION . . . . . . . . . . . . . .
Краткое содержание страницы № 3
MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mount- ing recommendations as you decide where to install your Casablanca fan. • For safety reasons, the fan blades must be a minimum of 7′ above the floor. • Do not locate th
Краткое содержание страницы № 4
th ™ 19 Century PREPARATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. GETTING STARTED Carton Contents Be sure to use only genuine Casablanca blades. The blade The fan carton contains the fan body, warranty card, owner's manual, and all the parts necessary to assemble and install your shrink wra
Краткое содержание страницы № 5
FAN PREPARATION IMPORTANT SAFETY INFORMATION! BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN, INSTALL THE THREADED DOWNROD INTO THE MOTOR COUPLING AND LOCK THE ASSEMBLY Prepare for fan installation as follows: Step D. Route the wires from the motor through the GROUND Perma Lock™ downrod and ball assembly, keeping the wires • WIRE to one side of the cross pin. MOTOR WIRES NOTE: The downrod has a tapered thread that is designed to lock completely when DOWNROD correctly installed. & BALL ASSE
Краткое содержание страницы № 6
th ™ 19 Century CEILING HARDWARE ADDITIONAL HARDWARE 1 2 /4" x 8-32 ROUNDED HEAD SCREW (2) CROSSBAR WIRE NUT (4) 1" x 8-32 ROUNDED MOUNTING FLAT WASHER (2) HEAD SCREW (2) BRACKET SUPPORT INSTALLATION PARTS LARGE FLAT WASHER 3 /8" (1) CANOPY ADAPTOR PLATE LAG SCREW 3 /8" #7 X 5" (1) ADAPTOR PLATE INSTALLATION JOIST Note: After removing the old fixture, check the outlet box to insure that it is supported by a joist or beam across its upper surface. If not, a 2" x 4" stud must be installed. Step 1
Краткое содержание страницы № 7
LAG SCREW INSTALLATION 1 Step 2. Route the outlet box wires through the /2″ diam- eter outer hole of the canopy adaptor plate. Attach the crossbar and canopy adaptor plate to outlet box with screws provided. Step 3. With the large washer attached, pass the lag screw through the center hole of canopy adaptor plate and screw into guide hole. Tighten until outlet box is firmly mounted to beam. This box must be firmly secured to the ceiling. We 1 /2″ DIAMETER recommend that the ceiling fixture outl
Краткое содержание страницы № 8
th ™ 19 Century HANGING THE FAN Step 5. To hang the fan body in the canopy, hold the fan CANOPY body firmly and insert the nylon ball into the canopy open- ing. Rotate fan body until slot on nylon ball fits into pin opposite canopy opening. NOTE: The fan weight is 35 pounds. BALL PIN SLOT CANOPY ELECTRICAL CONNECTIONS Step 6. Connect the fan wires to the outlet box wiring by placing the bare ends of the wires to- 2 BLACK WIRES gether and then securing with a wire nut. Connect in this order: • GR
Краткое содержание страницы № 9
DISASSEMBLE CANOPY AND MOTOR COVERS Step 10. Remove the screws from the canopy cover and the motor cover and set aside for later use. MOTOR COVER CANOPY COVER INSTALL CANOPY COVER Step 11. Take the two pieces of the canopy cover and assemble them around CANOPY the downrod as shown. Using the four COVER screws removed in Step 10, assemble the canopy cover. Slide the canopy cover to the ceiling and secure to the downrod using the two pro- vided screws. Tighten by hand only. SCREWS FROM STEP 10 C
Краткое содержание страницы № 10
th ™ 19 Century BLADE HARDWARE BLADE BLADE BLADE WASHER BLADE SCREW HOLDER ATTACH BLADE HOLDERS BLADE Step 13. Attach the blades to the blade holders by align- SCREW ing the screw holes of the holder with the holes of the blade. BLADE WASHER Attach the blade holder using the four blade screws and blade washers provided for each blade. Using the screwdriver, tighten securely by hand only. INSTALL BLADE ASSEMBLY Step 14. Remove the blade holder screw from the fan. Slide the blade assembly into the
Краткое содержание страницы № 11
LIGHT KIT WIRING NOTE: If you do not desire to install the light kit, see “Optional Switch Housing Cup” installation instructions on Page 11. Step 15. Remove the wire nuts on the BLACK and WHITE wires from the fan. If necessary re- 1 move the insulation from the last / ” of each 2 wire (fan and light fixture). Step 16. Attach the switch housing wires to the light fixture wires by placing the bare ends of the wires together and then securing with a wire nut. Connect in this order: WIRE • WHITE w
Краткое содержание страницы № 12
th ™ 19 Century GLASS HARDWARE 60 WATT TYPE A15 INCANDESCENT BULB GLASS SHADE GLASS & BULB INSTALLATION Step 18. Loosen the three glass screws for each fixture so the end of the screws are flush with the inside of the fixture. GLASS SHADE Slide the glass shade into the fixture and hold SCREWS firmly. Turn each screw several times, going in a circle, to assure that all glass screws have en- gaged the glass. Tighten securely by hand only. Step 19. Install the four 60 Watt type A15 bulbs into each
Краткое содержание страницы № 13
R INTELI•TOUCH © INSTALLING THE W-32 WALL CONTROL The wall control installs in the same manner as an ordinary light switch, using an existing junction box and wiring. This controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason the following precautions must be observed: 1. Use only the Casablanca W-32 wall control. 3. Do not use more than one fan per wall control. 4. No other light fixtures or electrical appliances may be con- 2. Do
Краткое содержание страницы № 14
R INTELI•TOUCH OPERATION POWER The button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunderstorms. It is also used to exit or enter additional programs. POWER must be left on to retain a previously set fan speed or light level. INTELI•TOUCH OPERATION SPEED CONTROL There are six individual speed settings for the fan; each speed is indicated by an audible tone of increasing pitch. FAN CONTROL To select the desired fan speed:
Краткое содержание страницы № 15
R ® INTELI•TOUCH OPERATION LIGHT-MINDER PROGRAM The Light-Minder program automatically turns OFF the fan mounted lights after two hours. To enter the Light-Minder Program: 1. Turn the OFF for at least three seconds. 2. Turn the ON. 3. Immediately operate the buttons in the following sequence: + + + 4. A series of tones indicates this command has been accepted. The fan and light will operate normally using the buttons to turn them on and off. But, if the lights are left on, they will auto
Краткое содержание страницы № 16
R TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes: For cleaning, a soft brush or lint-free cloth Never Lubricate this Fan! should be used to prevent scratching the finish. A vacuum cleaner The precision motor at the heart of your Casablanca fan features brush nozzle can remove heavier dust. Surface smudges or an accu- sealed bearings that are lubricated for life. Do not attempt to oil mulation o
Краткое содержание страницы № 17
761 CORPORATE CENTER DRIVE • POMONA, CA 91768 TOLL FREE: 888-CASA-1ST (227-2178) www.CasablancaFanCo.com ©COPYRIGHT 2000 CASABLANCA FAN COMPANY • U.S. PATENT PENDING PRINTED IN ROC
