Краткое содержание страницы № 1
Jasmine™ Scale JLS5
Assembly, Installation and Operating Instructions
SAVE THESE INSTRUCTIONS
NOTE: Check all parts for shipping damage. In case of shipping damage, DO NOT use. Contact carrier/dealer for
further instruction.
To ensure the safe installation, operation and use of the Jasmine Scale, these instructions MUST be followed:
WARNING
DO NOT use this equipment without first reading and understanding these instructions. If you are
unable to understand the Warnings, Cautions, and Instruc
Краткое содержание страницы № 2
Removing the Swivel Bar/Cradle Attachment NOTE: For this procedure, refer to FIGURE1. 1. Remove the side rubber caps. NOTE: Support the swivel bar or cradle attachment from underneath while removing the attaching hardware. 2. Remove the socket head screw, washer, bushings, top rubber cap, nylon spacers, washer and nut that attach the swivel bar or cradle attachment to the boom. NOTE: When the attaching hardware is removed, the pin, washer and o‐ring will become loose. NOTE: Save the socket scre
Краткое содержание страницы № 3
Installing the Jasmine Scale NOTE: For this procedure, refer to FIGURE2. WARNING Patient and sling MUST be removed from the lift during ALL installation procedures. 1. Position the load cell assembly of the Jasmine Scale into the boom mounting bracket (Detail ʺAʺ of FIGURE2). 2. Secure the Jasmine Scale to the boom mounting bracket with a bolt, washers, bushings, nylon washers, locknut and the top rubber cap. Securely tighten. Install the small rubber cap. NOTE: Refer to Detail ʺAʺ of FIGURE
Краткое содержание страницы № 4
Operating the Scale Keypad Functions INDICATOR INDICATOR KEY DISPLAYED LOCATION DEFINITION ON OFF Center of Display Window Pressing this key will apply power to the OFF scale and turn the unit on. When the scale is already on, pressing the button will turn the unit off. ZERO ZERO Lower Left Corner of the Pressing this key when the scale is on will Display Window reset the weight shown in the display window to zero. UNITS lb or kg Upper Right Corner of the The function of this key is to chan
Краткое содержание страницы № 5
WARNING DO NOT operate key strokes with pointed objects (e.g. pencils, pens, fingernails, etc.) Otherwise damage to the key pad will result. NOTE: The display will indicate the last weight that was measured. The word ʺLOCKʺ will be seen in the display box. NOTE: The ZERO key is pressed in order to avoid capturing the weight of the sling and the hardware. If the ZERO key is not pressed the weight of the sling and the weight of the hardware will be included in the weight displayed. NOT ZERO‐
Краткое содержание страницы № 6
Replacing the Battery NOTE: For this procedure, refer to FIGURE4. NOTE: The scale is powered by a 9‐volt alkaline battery that should provide approximately 1500 readings before needing replacement. When battery replacement is needed, LO BAT will appear on the display. Perform the following: 1. Slide the battery door open in the direction of the arrow. 2. Remove existing battery. 3. Install the NEW battery. 4. Reinstall the battery door. Assembled Scale 9V Battery Battery Door Arrow FIGURE 4
Краткое содержание страницы № 7
11. Remove the weight. Press the LOCK/UNLOCK key. NOTE: The scale is now in test mode. 12. Press the ZERO key. The display reads 0.00 lb. NOTE: The scale will now be in normal operation. BACK VIEW OF SCALE DISPLAY CAL button FRONT VIEW OF SCALE DISPLAY Display Window MODEL JLS5 CAPACITY 500 lb, 227 kg FIGURE 5 Calibrate the Jasmine Scale Troubleshooting SYMPTOM PROBABLE CAUSE SOLUTION Unit does NOT work properly. Battery failure. Check battery. Replace if necessary. Battery has been replaced
Краткое содержание страницы № 8
LIMITED WARRANTY PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975. This warranty is extended only to the original purchaser/user of our products. This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state. Invacare warrants the products manufactured (excluding the 9V battery) to be free from defects in materials and workmanship for a period of two years
