Краткое содержание страницы № 1
Random Orbit Sander
MODEL BO6030
003731
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Краткое содержание страницы № 2
SPECIFICATIONS Model BO6030 Pad size 150 mm (6”) Orbits per minute 4,000 - 10,000 Sanding stroke rate 8,000 - 20,000 Overall length 309 mm (12-1/8”) Net weight 2.3 kg (5.1 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious per
Краткое содержание страницы № 3
5. Avoid body contact with grounded sur- 14. Use safety equipment. Always wear eye faces such as pipes, radiators, ranges and protection. Dust mask, non-skid safety refrigerators. There is an increased risk of shoes, hard hat, or hearing protection must electric shock if your body is grounded. be used for appropriate conditions. Ordinary eye or sun glasses are NOT eye protection. 6. Do not expose power tools to rain or wet conditions. Water entering a power tool will Tool Use and Care increase t
Краткое содержание страницы № 4
24. When servicing a tool, use only identical SERVICE replacement parts. Follow instructions in 23. Tool service must be performed only by the Maintenance section of this manual. qualified repair personnel. Service or main- Use of unauthorized parts or failure to follow tenance performed by unqualified personnel Maintenance instructions may create a risk of could result in a risk of injury. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. W
Краткое содержание страницы № 5
SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD205-1 The followings show the symbols used for tool. V ....................... volts ................alternating current A ....................... amperes ....................no load speed n ˚ Hz ..................... hertz ....................Class II Construction .../min................orbits per minute 5
Краткое содержание страницы № 6
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 003732 Switch action 1 CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. 2 • Switch can be locked in “ON” position for ease of operator comfort during extended use. Apply caution 1. Lock button when locking tool in “ON” position and maintain firm 2. Swit
Краткое содержание страницы № 7
NOTE: • The figure shows standard applications. They may differ under certain conditions. CAUTION: • If the tool is operated continuously at low speeds for a long time, the motor will get overloaded, resulting in tool malfunction. • The speed adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function may no longer work. ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the
Краткое содержание страницы № 8
003740 Changing pad 1 2 Makita offers an extensive range of optional super soft and 3 atandard equipped soft pads. Remove the screw counter- clockwise from the center of the base with a hex wrench. After changing the pad, tighten the screw clockwise securely. 1. Hex wrench 2. Screw 3. Pad 003741 Installing dust bag Install the dust bag on the tool so that the arrow with “UP” indicated on the dust nozzle points upward. 2 1 1. Dust nozzle 2. Dust bag 003735 Emptying dust bag When the dust bag is a
Краткое содержание страницы № 9
003737 After emptying the dust bag, insert the hook on the dust noz- zle into the rectangular hole on one side of the dust bag frame and push up the dust bag frame until it clicks into place on the push button. 003742 Installing paper dust bag (optional accessory) 2 Place the paper dust bag on the paper dust bag holder with 1 its front side upward. Insert the front fixing cardboard of the paper dust bag into the groove of the paper dust bag holder. 3 1. Groove 2. Front fixing cardboard 3. Front
Краткое содержание страницы № 10
003744 Insert the notch of the paper dust bag into the guide of the paper dust bag holder. Then install the paper dust bag holder set on the tool. 2 1 1. Notch 2. Guide 003745 OPERATION 003746 Sanding operation CAUTION: • Never switch on the tool when it is in contact with the workpiece, it may cause an injury to operator. • Never run the tool without the abrasive disc. You may seriously damage the pad. • Never force the tool. Excessive pressure may decrease the sanding efficiency, damage the ab
Краткое содержание страницы № 11
• Never force the tool. Excessive pressure may decrease the polishing efficiency and cause motor overload, resulting in tool malfunction. 003747 Applying wax Use an optional sponge pad. Apply wax to the sponge pad or work surface. Run the tool to smooth out wax. NOTE: 1 • First, wax a non critical portion of the work surface to make sure that the tool will not scratch the surface or result in uneven waxing. 1. Sponge pad 003748 Removing wax Use an optional felt pad. Run the tool to remove wax. 1
Краткое содержание страницы № 12
ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center. • Hook-and-loop type abrasive discs (with pre-punched holes) • Sanding cloth 150 • Pad 150 (Super soft, Soft) •
Краткое содержание страницы № 13
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
Краткое содержание страницы № 14
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
Краткое содержание страницы № 15
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ARIZONA FLORIDA MISSOURI PENNSYLVANIA 3707 E. Broadway Rd., Ste. 6 750 East Sample Road 9876 Watson Road 1704 Babcock Blvd. Phoenix, AZ 85040 Pompano Beach, FL 33064 St. Louis, MO 63126-2221 Pittsburgh, PA 15209 (602) 437-2850 (954) 781-6333 (314) 909-9889 (412) 822-7370 CALIFORNIA GEORGIA NEBRASKA PUERTO RICO 41850 Christy St. 4680 River Green Parkway NW 4129 S. 84th St. 200 Guayama St. Fremont, CA 94538-5107 Duluth,
Краткое содержание страницы № 16
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
