Руководство по эксплуатации Makita BO45502

Краткое содержание страницы № 1

Sander
Finishing
MODEL BO4550
MODEL BO45502
Without dust bag
and punch plate
INSTRUCTION MANUAL
DOUBLE
INSULATION
SPEC IF1 CAT1 ONS
Dimensions (L x W x H) Net weight
No load speed lOPMl
Pad size
0.95 kg
11 5 mm x 112 mm x 130 mm
112mmxlOOmm
14,000
(4-112" x 4-318" x 5-118") (2.1 lbsl
(4-3/8" x 4")
Manufacturer reserves the right to change specifications without notice.
Note: Specifications may differ from country to country.

Краткое содержание страницы № 2

IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence

Краткое содержание страницы № 3

14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are t

Краткое содержание страницы № 4

Attaching abrasive paper CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the paper. Raise the lever. Insert the paper end into the clamper, aligning the paper edges even and parallel with the sides of the base. (Prebending the paper makes attachment easier.) Once the paper is in place, return the lever to its original position. Repeat the same process for the other end of the base, maintaining the proper paper tension. CAUTION: Aft

Краткое содержание страницы № 5

Switch action To start the tool, move the switch to the "ON" position. To stop, move the switch to the "OFF" position. Operation Hold the tool firmly. Turn the tool on and wait until it attains full speed. Then gently place the tool on the workpiece surface. A finishing sander is generally used to re- move only a small amount of material at a time. Since the quality of the surface is more important than the amount of stock removed, do not bear down on the tool. Keep the base flush w

Краткое содержание страницы № 6

OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper

Краткое содержание страницы № 7

FINISHING SANDER Model BO4550 Model BO45502 7

Краткое содержание страницы № 8

MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or mater