Краткое содержание страницы № 1
XE 850
Elliptical
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW ELLIPTICAL!
Краткое содержание страницы № 2
Table of Contents Product Registration 2 Important Safety Instructions .3 Important Electrical Information .4 Important Operation Instructions .. .4 Assembly Instructions 5 Features 14 Operation of Your New Elliptical ..15 Manufacturer s Limited Warranty .26 ATTENTION-THIS ELLIPTICAL IS INTENDED FOR RESIDENTIAL AND LIGHT COMMERCIAL USE ONLY AND IS WARRANTED FOR THESE APPLICATIONS. ANY OTHER APPLICATION VOIDS THIS WARRANTY IN ITS ENTIRETY.
Краткое содержание страницы № 3
CONGRATULATIONS ON YOUR NEW ELLIPTICAL AND WELCOME TO THE SPIRIT FAMILY! Thank you for your purchase of this quality elliptical trainer from Spirit Manufacturing, Inc. Your new elliptical was manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available. Through your dealer, Spirit will do all we can to make your ownership experience as pleasant as possible for many years to come. The local dealership where you purchased
Краткое содержание страницы № 4
Important Safety Instructions WARNING - Read all instructions before using this appliance. Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both the carpet and elliptical may result. Keep children away from the elliptical. There are obvious pinch points and other caution areas that can cause harm. Keep hands away from all moving parts. Keep the cord away from heated surfaces. Never drop or insert any object into any openings. Do not use outdoors. Do not attempt
Краткое содержание страницы № 5
Important Electrical Information WARNING! When operated in the generator mode, be aware that the generator is producing A.C. power while the elliptical is being used. Do not service the elliptical while the generator is spinning. Serious electric shock could occur. NEVER: expose this elliptical to rain or moisture. This product is NOT designed for Use outdoors, near a pool or spa, or in any other high humidity environment. Important Operation Instructions NEVER operate this elliptical without
Краткое содержание страницы № 6
Assembly Pack Check List Step 1 (#96) 3/8" x 19 x 1.5T (#104) 3/8" x 23 x 2.0T Flat Washer (2pcs) Curved Washer (4pcs) (#84) M5 x 12m/m (#75) 3/8 x 2-1/4 Phillips Head Screw (2pcs) Hex Head Bolt (2pcs) (#77) 3/8 x 3-3/4 Hex Head Bolt (4pcs) Step 2 (#84) M5 x 12m/m (#128) 3/8" x 2.0T (#104) 3/8" x 23 x 2.0T Split Washer (1pc) Phillips Head Screw (4pcs) Curved Washer (2pcs) (#76) 3/8 x 3/4 (#75) 3/8 x 2-1/4 Button Head Socket Screw (2pcs) Hex Head Bolt (1pc)
Краткое содержание страницы № 7
Step 3 (#102)Ø 25 Wave (#131) 3/8" x 35 x 2.0T Washer (2 pcs) Flat Washer (2 pcs) (#76) 3/8 x 3/4 Button Head Socket Screw (2pcs) Step 4 (#91) 5/16" x 7T (#107) 3.5 x 12m/m Nylon Nut (2 pcs) Self Tapping Screw (2 pcs) (#84) M5 x 12m/m (#100) 5/16" x 18 x 1.5T Phillips Head Screw (26 pcs) Flat Washer (2 pcs) (#79) 5/16 x 1-1/4 (#80) 5/16 x 3/4 Hex Head Bolt (2 pcs) Hex Head Bolt (4 pcs) 6 XE Series Elliptical
Краткое содержание страницы № 8
Tools (#33) Bolt Cap (2 pcs) (#126) Phillips Screw Driver (1 pc) (#125) Short Screw Driver (1 pc) (#124) 13/14m/m Wrench (1 pc) (#129) 12m/m Wrench (1 pc) 7 XE Series Elliptical
Краткое содержание страницы № 9
Assembly Instructions UNPACKING THE UNIT 1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift Box over the unit and unpack. 2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged parts are found, or parts are missing, contact your dealer immediately. 3. Locate the hardware package. The hardware is separated into four steps. Remove the tools first. Remove the hardware for each step as needed to avoid confu
Краткое содержание страницы № 10
STEP 2: CONSOLE MAST ASSEMBLY 1. Remove the hardware from the hardware pack for step 2. You should have one 3/8 x 2-1/4 bolt (75), one split lock washer (128), two 3/8 x 3/4 bolts (76), two curved washers (104) and four M5 X 12mm Phillips head screws (84). 2. Locate the console mast (12) and console mast cover (49) and slide the cover onto the mast as far as it will go. Make sure the cover is facing the correct way. 3. At the top opening of the main body of the elliptical is a wire harness (
Краткое содержание страницы № 11
10 XE Series Elliptical
Краткое содержание страницы № 12
STEP 3: HANDLE BAR ASSEMBLY 1. Remove the hardware from the hardware pack for step 3. You should have two 3/8 x 3/4 bolts (76), two large flat washers (131) and two large wave washers (102). Also locate the two plastic end caps (33) from the tool section of the hardware pack. 2. Locate and install the two large wave washers (102) onto the handle bar axle, one on each side. 3. Slide the left and right handle bars onto the appropriate side of the axle. There is a sticker on each handle bar indica
Краткое содержание страницы № 13
STEP 4: FOOT PAD/CONNECTING ARM ASSEMBLY. Rear shroud installation. 1. Remove the hardware from the hardware pack for step 4. You should have two 5/16 x 1-1/4 bolts (79), two flat washers (100), two nylon nuts (91), four 5/16 x 3/4 bolts (80), two self-tapping Phillips head screws (107) and twenty-six M5 x 12mm screws (84). 2. On the pedal arms, in the middle on top, there are two axles (23) already installed in the bushing housings. Remove the bolt and washer (74, 99) from each then remove
Краткое содержание страницы № 14
84 71 72 107 84 84 71 72 107 84 84 64 152 84 84 153 84 152 84 84 84 153 84 150 84 151 13 XE Series Elliptical
Краткое содержание страницы № 15
Features Footpads Through research performed with a leading sports scientist and physical rehabilitation expert, Spirit engineering has developed a breakthrough in pedal design. The history of elliptical use over the past few years tells us that many users suffer from ankle, Achilles tendon, knee and/or hip pain. While researching a solution to these common problems Spirit engineers consulted Richard DeKok, P.T., M.T.C., of St. Bernards Industrial Rehabilitation Center in Jonesboro Arkansas. Tog
Краткое содержание страницы № 16
Operation of Your Elliptical XE850 Console Power on The XE850 Elliptical has a built-in generator for power and does not need to be plugged into an AC outlet. To power up the XE850 simply start to pedal, the console will turn on automatically. If the console does not light when you pedal, check that the power switch is set to 0 (Generator). The switch is located on the front, lower left side of the main plastic cover. This switch should always be set to for generator. The A.C. setting is for
Краткое содержание страницы № 17
Quick Start This is the quickest way to start a workout. After the console powers up you just press the Start key to begin. This will initiate the Quick Start mode. In Quick Start the Time will count up from zero, all workout data will start to accrue and the workload may be adjusted manually by pressing the Up or Down buttons. The dot matrix display will show only the bottom row lit at first. As you increase the workload, more rows will light indicating a harder workout. The elliptical will get
Краткое содержание страницы № 18
a program the Stop/Reset key performs a Previous Screen function. This allows you to go back one step in the programming each time you press the Stop/Reset key. The Program Keys are used to preview each program. When you first turn the console on you may press each program key to preview what the program profile looks like. If you decide that you want to try a program, press the corresponding program key and then press the Enter key to select the program and enter into the data-setting mode. The
Краткое содержание страницы № 19
except the User 1&2 programs. The last Age and Weight entered will be saved as the new default settings. If you enter your Age and Weight the first time you use the Elliptical you will not have to enter it every time you work out unless either your Age or Weight changes or someone else enters a different Age and Weight. Manual The Manual program works as the name implies, manually. This means that you control the workload yourself and not the computer. To start the Manual program follow the inst
Краткое содержание страницы № 20
The Programs HILL The Hill program simulates going up and down a hill. The resistance in the pedals will steadily increase and then decrease during the program. To start the Hill program follow the instructions below or just press the Hill button then the Enter button and follow the directions in the message window. 1. Press the Hill key then press the Enter key. 2. The message window will ask you to enter your Age. You may enter your Age, using the Up and Down keys or the numeric key pad, then
