Краткое содержание страницы № 1
SIDE BY SIDE BUILT-IN REFRIGERATOR
Installation Guide
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. INSTALLATION REQUIRES 2 OR MORE PEOPLE.
REFRIGERADOR EMPOTRADO
DE DOS PUERTAS
Guía de instalación
IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. LA INSTALACIÓN REQUIERE DE 2 O MÁS PERSONAS.
RÉFRIGÉRATEUR ENCASTRÉ CÔTE À CÔTE
Guide d’installation
IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. L’INSTALLATION NÉCESSITE L’INTERVENTION DE 2 PERSONNES OU PLUS.
Table of Contents/Índice/Table des matière
Краткое содержание страницы № 2
TABLE OF CONTENTS REFRIGERATOR SAFETY........................................................................... 3 INSTALLATION INSTRUCTIONS............................................................. 19 Unpack the Refrigerator ......................................................................... 19 MODELS....................................................................................................... 4 Reduce Tipping Radius ............................................................
Краткое содержание страницы № 3
REFRIGERATOR SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean: You can be killed or seriously injured if you don't immediatel
Краткое содержание страницы № 4
MODELS Side by Side Non-Dispensing Refrigerators ® Architect Series Classic Series Features wraparound styling that complements the contoured Features factory-installed, traditional style trim to provide a door handles. This series provides a warm commercial-looking “framed” look. This series requires the installation of custom built-in refrigerator. panels that are not included. KSSC36FTS KSSC42FTS KSSC48FTS KSSS36FTX KSSS42FTX KSSS48FTX Overlay Series Features factory-installed, overlay sty
Краткое содержание страницы № 5
Side by Side Dispensing Refrigerators ® Architect Series Classic Series Features wraparound styling that complements the contoured Features factory-installed, traditional style trim to provide a door handles. This series provides a warm commercial-looking “framed” look. This series requires the installation of custom built-in refrigerator. panels that are not included. KSSC36QTS KSSC42QTS KSSC48QTS KSSS36QTB KSSS42QTB KSSS48QTB KSSS36QTW KSSS42QTW KSSS48QTW KSSS36QTX KSSS42QTX KSSS48QTX Overl
Краткое содержание страницы № 6
INSTALLATION REQUIREMENTS Tools and Parts Location Requirements IMPORTANT: The refrigerator can be recessed in an opening between cabinets or installed at the end of a cabinet run using a side panel to ■ Installer: Leave Installation Instructions with the homeowner. enclose the refrigerator. ■ Homeowner: Keep Installation Instructions for future reference. Save these Installation Instructions for the local electrical inspector’s use. WARNING TOOLS NEEDED: Gather the required tools and parts
Краткое содержание страницы № 7
■ A grounded 3 prong electrical outlet should be located within a specified number of inches from the right-hand side Electrical Requirements cabinets or end panel. See the chart following the graphic for the number of inches required for your model. For more information, see “Electrical Requirements.” WARNING ■ The water shutoff should be located in the base cabinet on either side of the refrigerator or some other easily accessible area. If the water shutoff valve is not in the cabinets,
Краткое содержание страницы № 8
Water Pressure Water Supply Requirements ■ All installations must meet local plumbing code requirements. A cold water supply with water pressure between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ■ The water shutoff should be located in the base cabinet on ice maker. If you have questions about your water pressure, call a either side of the refrigerator or some other easily accessible licensed, qualified plumber. area. The right-hand side is recommended.
Краткое содержание страницы № 9
Product Dimensions Side View Front View ■ The depth from the front of the top grille to the back of the ■ Width dimensions were measured from trim edge to trim refrigerator cabinet is 25³⁄₈" (64.5 cm). edge. ■ The power cord is 84" (213 cm) long. ■ Height dimensions are shown with leveling legs extended ¹⁄₈" (3 mm) below the rollers. ■ The water line attached to the back of the refrigerator is 5 ft (1.5 m) long. ■ Height dimensions are shown with leveling legs extended ¹⁄₈" (3 mm) below th
Краткое содержание страницы № 10
Door Swing Dimensions The location must permit both doors to open to a minimum of 90°. Allow 4¹⁄₂" (11.4 cm) minimum space between the side of the 42" (106.7 cm) Models refrigerator and a corner wall. NOTE: More clearance may be required if you are using overlay 12⁵⁄₈" panels, custom handles, or extended handles on a Classic model. (32.1 cm) To adjust the door swing, see “Adjust Doors.” 41¹⁄₂" 37¹⁄₄" 36" (91.4 cm) Models (105.4 cm) (94.6 cm) 16⁷⁄₈" 10⁷⁄₈" (42.9 cm) (27.6 cm) 41³⁄₈" 47⁷⁄₈"
Краткое содержание страницы № 11
Overlay Panel Backer Panel Door Spacer Panel Overlay Series Door Panel and Cabinetry Clearance The custom door panels and adjacent cabinetry must be designed so that there is sufficient clearance for the doors to swing open. If the refrigerator is to be installed close to the wall, see “Door Swing 90°” on next page. Door Swing 110˚ Actual Size Refrigerator to Cabinetry Clearance Refrigerator Side Trim 1 1 /2" (3.8 cm) 1 1 /4" (3.2 cm) 1" (2.5 cm) Cabinetry 1 /4" (6.35 mm) Hinge 1 /2" (1.3 cm
Краткое содержание страницы № 12
Overlay Panel Backer Panel Door Spacer Panel Door Swing 90˚ Actual Size Refrigerator to Cabinetry Clearance Refrigerator Side Trim 1" (2.5 cm) 3 /4" (1.9 cm) 1 /2" (1.3 cm) 90˚ Door Stop Position Cabinetry 1 /4" (6.35 mm) Hinge 1 /2" (1.3 cm) 3 /4" (1.9 cm) 1" (2.5 cm) 1 /2" (1.3 cm) 3 /4" (1.9 cm) 1" (2.5 cm) 1 1 /4" (3.2 cm) 1 1 /2" (3.8 cm) Allow a minimum of 4¹⁄₂" (11.4 cm) of space between the side of the refrigerator and a corner wall. More clearance may be needed if thicker custom pane
Краткое содержание страницы № 13
Overlay Series Custom Panels and Handle Kits Custom overlay panels allow you to blend the exterior of your refrigerator into the overall kitchen décor, and to use custom Decorative Overlay Panel handles for additional design flexibility. The custom panels must have backer panels attached in order to C mount them to the refrigerator. It is most common to work with three panels, as shown in the following graphic: a decorative overlay panel, a ¹/₈" (3.18 mm) spacer panel or spacer strips and
Краткое содержание страницы № 14
Backer Panels Dispenser Frame (dispenser models only) NOTES: The dispenser frame attaches to the panel with 4 screws. ■ Dashed lines represent placement of backer panels on overlay To remove the dispenser frame: panels. 1. Remove the four screws attaching the frame. ■ Illustration shows backer panels placed on decorative 2. Pull the dispenser frame from the decorative panel. overlays. 3. To replace the frame, hold the frame to the panel and replace the screws. C 6³⁄₁₆" (15.7 cm) Side Offset A
Краткое содержание страницы № 15
® Overlay Series Door Handle Kits Architect Series The following handle styles are available. Contact your KitchenAid Handles dealer or KitchenAid Parts and Accessories at PART NO. COLOR 1-800-442-9991. In Canada, call 1-800-807-6777. 4396103 Stainless Steel 8171760 Biscuit 4396105 White 4396106 Black Classic Series Factory Panels and Kits All factory parts are available through your KitchenAid dealer or by calling KitchenAid Parts and Accessories at 1-800-442-9991. In Canada, call 1-800-807-
Краткое содержание страницы № 16
Classic Series Custom Panels If you plan to install custom wood panels, you will need to create the panels yourself or consult a qualified cabinetmaker or Door Panels for Non-dispenser Models carpenter. See dimension drawings for panel specifications. The freezer panel should not weigh more than 40 lbs (18.1 kg). IMPORTANT: Panels weighing more than recommended may The refrigerator panel should not weigh more than 50 lbs (23 kg). cause damage to your refrigerator. NOTE: Dimensions shown hav
Краткое содержание страницы № 17
Door Panels for Dispenser Models Dispenser Frame (Classic series dispenser models) The freezer panel should not weigh more than 40 lbs (18.1 kg). The dispenser frame attaches to the panel with 4 screws. The refrigerator panel should not weigh more than 50 lbs (23 kg). To remove the dispenser frame: B A 1. Remove the four screws attaching the frame. 2. Pull the dispenser frame from the decorative panel. 3. To replace the frame, hold the frame to the panel and replace ¹⁄₂" ¹⁄₂" the screws. (1.27
Краткое содержание страницы № 18
® Inset Installation Dimensions Classic, Architect and Complete Series Custom Side Panels 1. Measure the distance from point A (as shown) to the back wall. Add ⁷⁄₃₂" (5.6 mm) to this measurement to allow the side Custom side panels may be needed when not enough space is panel to fit into the trim. available to have cabinets on both sides of the refrigerator or when the refrigerator is placed at the end of a cabinet run. You 2. If the panel is more than ¹⁄₄" (6.35 mm) thick, route the front
Краткое содержание страницы № 19
Refrigerator Recessed Inset Installation Dimensions Overlay 1. Measure the distance from point A (as shown) to back wall. 2. Route the front edge of the support board or attach a ³⁄₈" (9.5 mm) board to hold the panel in the cabinet side trim. 23¹¹⁄₁₆" (60.16 cm) A INSTALLATION Side Trim INSTRUCTIONS ³⁄₁₆" (4.5 mm) ³⁄₈" (9.7 mm) Unpack the Refrigerator WARNING Tip Over Hazard ¹⁄₁₆" (1.5 mm) Refrigerator is top heavy and tips easily when not completely installed. Keep doors taped closed unt
Краткое содержание страницы № 20
NOTE: Pass the dolly strap under the handles for the ® Architect Series. Reduce Tipping Radius (if required) Before bringing the refrigerator into the home, be sure there is adequate ceiling height to stand the refrigerator upright. See “Tipping Radius” in the “Installation Requirements” section for more information. If you do not have adequate ceiling height to stand the refrigerator upright, the tipping radius can be reduced by removing the top grille and side trims (see the following
