Краткое содержание страницы № 1
1012552
3-POINT MOUNTING KIT
For Woods BH70X, BH80X Backhoes
Tested. Proven. Unbeatable.
SAVE THIS
MANUAL!
Include it with
your Backhoe Manual.
It contains safety,
operation, and repair
part information not
found in other
manuals.
MAN0472
(9/23/2005)
INSTALLATION MANUAL
Краткое содержание страницы № 2
TO THE DEALER: ® Assembly and proper installation of this product is the responsibility of the Woods dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Product Registration included with this manual. The customer must sign the registration which certifies that all Dealer Check List items have been completed. The dea
Краткое содержание страницы № 3
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Keep hands and body away from pressurized ! lines. Use paper or cardboard, not hands or other LEA EL INSTRUCTIVO! body parts to check for leaks. Wear safety goggles. Si no lee Ingles, pida ayuda a Hydraulic fluid under pressure can easily penetrate alguien que si lo lea para que le skin and will cause serious injury or death. traduzca las medidas de seguridad. Make sure that all operating and service person- nel know that if hydra
Краткое содержание страницы № 4
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) extreme care. Always stand between rear tire and backhoe Always wear relatively tight and belted clothing stabilizer arms or along side of tractor to avoid to avoid getting caught in moving parts. Wear being trapped should the boom swing control sturdy, rough-soled work shoes and protective be accidentally activated. equipment for eyes, hair, hands, hearing, and head; Never leave equipm
Краткое содержание страницы № 5
BACKHOE 3-POINT MOUNT INSTALLATION TRACTOR PREPARATION NOTE: For installing this 3-point mounting kit, refer- ence to right, left, forward and rearward directions are TRACTOR HIGH determined from the operator’s position in the back- STRENGTH TOP hoe seat. LINK PIN NOTE: Leave all hardware loose until mounting kit 40" Minimum Radius has been fit up. 1. Refer to the WOODS BH70X/BH80X Backhoe Operator’s Manual for backhoe assembly instruc- HEAVY-DUTY tions. TOP LINK 2. Remove the tractor top link
Краткое содержание страницы № 6
Attach Top Link Bars to Backhoe 1. Attach top link bar (3) to the main frame using cap 1. 1007345 Double top link screw (8), hardened flat washer (15), and hex nut 3. 1012532 Top link bar (11). 8. 12558 3/4 NC x 4-1/2 HHCS GR5 2. Slide double top link (1) over top link bar (3) and 10. 14334 3/4 NC x 3 HHCS GR5 secure using cap screw (10), hardened flat 11. 1450 3/4 NC Hex nut washer (15), and hex hut (11) through end hole 15. 57798 3/4 Hardened flat washer on double top link. See Figure 3. NO
Краткое содержание страницы № 7
Attach 3-Point Mount to Backhoe 8 3. Attach lock bar (7) to right (4) and left (5) rear brackets using cap screws (9), four (two per side) hardened flat washers (15), and hex nuts (11). Do 15 not tighten nuts at this time. 4. Swing lock bar up and attach it to the double top link bar using cap screw (8), hardened flat washer 11 (15), and hex nut (11). See Figure 5. 7 15 11 4. 1012534 Right rear bracket 5. 1012535 Left rear bracket 15 7. 1012582 Lock bar 9 8. 12558 3/4 NC x 4-1/2 HHCS GR5 9. 1
Краткое содержание страницы № 8
Attach Backhoe to Tractor (Continued) 5. Connect tractor 3-point lower lift arms to the mounting pins on the backhoe. Secure using klik pin (14) and washers (17). Use washers to take up slack between klik pin and 3-point arm. See Figure 7. 6. Connect double top link bar to the tractor top link bracket. Use top link pin supplied with your tractor 17 and sleeve (12). If necessary, separate and adjust top link bars IN or OUT to maintain the backhoe vertical position. See “Tractor Connections” on
Краткое содержание страницы № 9
Remove Backhoe The only time the backhoe may be operated from a position other than the operator seat is during backhoe attachment and removal. Opera- tor must Read Mounting Kit Manual instructions on attaching and removing backhoe and use extreme care. Always stand between rear tire and back- hoe stabilizer arms or along side of tractor to avoid being trapped should the boom swing 6" Blocks BH1 control be accidentally activated. Figure 9. Backhoe Storage Position (Typical) 1. Remo
Краткое содержание страницы № 10
Attach Backhoe to Tractor 5. Raise the 3-point mount up by lowering stabilizers and boom section until even with tractor 3-point lift arms. Attach tractor 3-point lift arms to right and left rear brackets using washers (17) and klik This mounting kit is designed to provide pins (14). See page 12 for parts list. secure mounting and adequate operator clear- 6. Raise backhoe with stabilizer and boom section ance when properly installed. Check clearance to establish ground clearance betwee
Краткое содержание страницы № 11
Tractor Connections 2-1/2" 1 There may be more than one hole provided in tractor Max. top link attachment bracket. Select hole A, B, or C that most evenly distributes the load between top link 2 bracket top and bottom mounting bolts. See Figure A 10. For the Massey Ferguson 1455V tractor use hole position D. 3 NOTE: The maximum width between tractor top link attachment plates must not exceed 2-1/2 inches. This B will prevent excessive bending loads to the tractor top link pin. 4 For tractors w
Краткое содержание страницы № 12
1012552 3-POINT MOUNTING KIT 8 12 1 10 15 11 8 15 11 3 11 15 15 7 11 15 9 16 15 17 6 4 14 CD6779 13 5 REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 1007345 1 Double top link 10 14334 * 1 3/4 NC x 3 HHCS GR5 3 1012532 1 Top link bar 11 1450 * 5 3/4 NC Hex nut 4 1012534 1 Right rear bracket 12 30067 1 Sleeve, .765 x 1.0 x 1.69 5 1012535 1 Left rear bracket 13 33661 2 Category 1 mounting pin (w/nut & lw) 6 1012567 4 M 22 Nord lock washer 14 35124 2 7/16 x 2 Klik pin 7 1012582 1 Lock bar 15 57
Краткое содержание страницы № 13
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. All torque values are given to specifications used on hardware define
Краткое содержание страницы № 14
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 3/8 1/2 5/8 3/4 7/8 IN 1 2 7 34 5 6 MM 25 50 75 100 125 150 175 Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG .............................................................Agriculture NC .................................................... National Coarse ATF .............................. Automatic Transmission Fluid NF..
Краткое содержание страницы № 15
WARRANTY TM TM (All Models Except Mow’n Machine Zero-Turn Mowers and Woods Boundary Utility Vehicles) Please Enter Information Below and Save for Future Reference. Date Purchased: __________________________ From (Dealer): ________________________________________ Model Number: __________________________ Serial Number:________________________________________ Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set forth bel
Краткое содержание страницы № 16
WARRANTY TM (Replacement Parts For All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary Utility Vehicles) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months. Under no circumstances will this Warranty apply in th
