Краткое содержание страницы № 1
SYS7180VE
PICMG Single Board Computer
For socket 478 CPU With VGA/ LAN
TM
(Pentium 4™&Celeron™& Intel® Celeron®D CPU)
User’s Manual
Краткое содержание страницы № 2
Copyright Additional Information and Assistance This document is copyrighted, © 2004. All rights are reserved. The original 1. The manufacturer recommends using a grounded plug to ensure proper manufacturer reserves the right to make improvements to the products motherboard operation. Care should be used in proper conjunction described in this manual at any time without notice. with a grounded power receptacle to avoid possible electrical shock. No part of this manual may be reprod
Краткое содержание страницы № 3
Table of Contents Table of Contents 2.5.10 VGA CONNECTOR: .......................................................21 2.5.11 KEYBOARD / MOUSE CONNECTOR:...............................21 Table of Contents 2.5.12 CPU FAN CONNECTOR:...............................................21 CHAPTER 1 INTRODUCTION ...............................................1 2.5.13 ACPI CONNECTOR: J2..................................................22 1.1 SPECIFICATION.................................................
Краткое содержание страницы № 4
CHAPTER 1 – Introduction CHAPTER 1 – Introduction PS/2 1 to 2 adapter *1 Chapter 1 Introduction Com extension cables with bracket *1 Com, Printer extension cables with bracket *1 1.1 Specification +12V power cable *1 TM Processor Support Intel® Pentium 4 CPU up to 3.06 GHz USB cable *1 Special for SYS7180VE TM Support Intel® Celeron CPU up to 2.60 GHz Jumper Short Pin: 6 pcs TM Support Intel® Celeron®D CPU up to 2.80 GHz (Prescott core) Chipset
Краткое содержание страницы № 5
CHAPTER 1 – Introduction CHAPTER 1 – Introduction 3.3 V output must reach its minimum regulation level within 20ms of the +5V 1.5 Connector & Jumper Location output reaching its minimum regulation level The following table lists the power supply’s tolerances for DC voltages: DC Voltage Acceptable Tolerance +3.3 V ± 5 % +5 V ± 5 % +5 VSB (standby) ± 5 % -5 V ± 5 % +12 V ± 5 % -12 V ± 5 % SYS7180VE User’s Manual 3 4 SYS7180VE User’s Manual
Краткое содержание страницы № 6
DATA DATA CTRL CTRL ADDR ADDR CHAPTER 1 – Introduction CHAPTER 2 –Hardware Installations Chapter 2 Hardware Installations 1.6 Block Diagram This chapter provides information on how to use the jumpers and connectors on the SYS7180VE in order to set up a workable system. CLOCK Processor SOCKET 478 2.1 Installation procedure ICS950220 PWM P4 PROCESSOR 2.1.1 Insert the system BIOS (if not already installed) genteelly. Pay attention to the position of pin 1 of BIOS socket. 2.1.2 Install t
Краткое содержание страницы № 7
CHAPTER 2 –Hardware Installations CHAPTER 2 –Hardware Installations 2.2 CPU Installation: 2.3 Main Memory Installation: DIMM1/2 ® TM The SYS7180VE Industrial CPU Card supports a single Intel P4 Celeron or The SYS7180VE Industrial CPU Card supports two single-side or double-sided TM TM DDR266/333 unregistered, DIMM 184-pin sockets for a maximum total memory of 1GB. Celeron D processor and Pentium 4 processor. The processor’s VID pins Using the non-ECC DDR SDRAM DIMMS. automatically program
Краткое содержание страницы № 8
CHAPTER 2 –Hardware Installations CHAPTER 2 –Hardware Installations Chipset 2.4 Jumper Settings: Intel 82845GV GMCH overview The features: Jumper setting 400/533 MHz PSB (100/133MHz bus clock) Jumper Default setting FSB setting: auto Short 1-2 FSB 32-bit addressing for access to 2GB of memory space up to 2GB of 266MHz Clear CMOS Normal mode Short 2-3 JCC or 333 MHz DDR SDRAM. BIOS write-protect: disabled Open JAV Supports only for un-buffered non-ECC DIMMs. AT or ATX selec
Краткое содержание страницы № 9
CHAPTER 2 –Hardware Installations CHAPTER 2 –Hardware Installations 2.5 Connectors Setting: 2.4.4 AT/ATX Power Setting J4 Options Settings 1 Connectors Label Connectors Label Short 1-2 (default) AT 2 IDE1 J2 Short 2-3 Primary IDE Connector ACPI Connector ATX 3 IDE2 VGA Secondary IDE Connector VGA Connector J4 FLOPPY MS FDD Connector PS/2 Mouse Connector LPT KB Printer Port Connector PS/2 Keyboard Connector 2.4.5 Watchdog Setting: JWD Keyboard/Mouse USB1_2 MKB USB 1_
Краткое содержание страницы № 10
CHAPTER 2 –Hardware Installations CHAPTER 2 –Hardware Installations 2.5.1 Front Panel Connector: J1 2.5.2 USB Connector: USB1-2 USB3-4 This header can be connected to a front panel power switch. The front panel Note: USB cable is special designed for SYS7180VE connector includes headers for these I/O connections: The Universal Serial Bus (USB) that allows plug and play computer peripherals Power switch such as keyboard, mouse, joystick, scanner, printer, modem/ISDN, CD-ROM and f
Краткое содержание страницы № 11
CHAPTER 2 –Hardware Installations CHAPTER 2 –Hardware Installations 2.5.4 Serial Port connector: COM1/COM2 COM1, COM2 are use in the 10-pins box-header, are onboard serial ports of the CPU card SYS7180VE. The following table shows the pin assignments of these connectors. 2.5.3 Parallel Port Connector: LPT COM1/2 Description Pin The parallel port bracket can used to add an additional parallel port for additional 9 1 Data Carrier Detect (DCD) parallel devices. There are four option
Краткое содержание страницы № 12
CHAPTER 2 –Hardware Installations CHAPTER 2 –Hardware Installations 2.88 MB, 3.5-inch These connectors support the provided IDE hard disk ribbon cable. After connecting the single end to the board, connect the two plugs at the other end to your hard This connector supports the provided floppy drive ribbon cable. After connecting disk(s). If you install two hard disks, you must configure the second drive to Slave mode the single and to the board, connect the two plugs on the other end to the
Краткое содержание страницы № 13
CHAPTER 2 –Hardware Installations CHAPTER 2 –Hardware Installations 2.5.9 External Keyboard/Mouse Connector: 2.5.8 Adapter connector for GIGA LAN: LAN2 There are two 5-pin connectors for external keyboard&mouse. This connector is for the GIGA LAN adapter that 10/100/1000 Base-TX RJ45 single port (1X1) tab-UP with LEDs integrated magnetics connector. The follow table shows the pin assignments of this connector. PIN No. Function PIN No. Function CN18 1 TCT3 9 TD4- 1 2 3 4 5 6
Краткое содержание страницы № 14
CHAPTER 2 –Hardware Installations CHAPTER 2 –Hardware Installations 2.5.13 ACPI Connector: J2 2.5.10 VGA Connector: When used with an ATX-compliant power supply that supports remote power It is a VGA CRT connector. The pin assignments are as follows: on/off, the CPU card can turn off the system power through software control. PIN No. Function PIN No. Function To enable soft-off control in software, advanced power management must be 1 Red 2 Green enabled in the Setup program and in th
Краткое содержание страницы № 15
CHAPTER 2 –Hardware Installations CHAPTER 3 - BIOS SETUP Chapter 3 BIOS Setup 3.1 Introduction This chapter discusses Award’s Setup program built into the FLASH ROM BIOS. The Setup program allows users to modify the basic system configuration. This special information is then stored in battery-backed RAM so that it retains the Setup information when the power is turned off. The rest of this chapter is intended to guide you through the process of configuring your system using Setup. St
Краткое содержание страницы № 16
CHAPTER 3 - BIOS SETUP CHAPTER 3 - BIOS SETUP the PageUp and PageDown keys to change entries, press for help and press to These defaults have been carefully chosen by both Award and your systems manufacturer quit. The following table provides more detail about how to navigate in the Setup program to provide the absolute maximum performance and reliability. Even a seemingly small using the keyboard. change to the chipset setup has the potential for causing you to use the overr
Краткое содержание страницы № 17
CHAPTER 3 - BIOS SETUP CHAPTER 3 - BIOS SETUP Advanced Chipset Features 3.3 Standard CMOS Setup Use this menu to change the values in the chipset registers and optimize your system's performance. Integrated Peripherals Use this menu to specify your settings for integrated peripherals. See section 6.6. for the details. Power Management Setup Use this menu to specify your settings for power management. PnP / PCI Configuration This entry appears if your system supports PnP / PCI.
Краткое содержание страницы № 18
CHAPTER 3 - BIOS SETUP CHAPTER 3 - BIOS SETUP Item Options Description Item Options Description EGA/VGA Min = 0 Landing zone **** CGA 40 Max = 65535 Video Select the default video device CGA 80 Min = 0 Sector Number of sectors per track MONO Max = 255 All Errors No Errors Select the situation in which you 3.4 Advanced BIOS Features Setup Halt On All, but Keyboard want the BIOS to stop the POST All, but Diskette process and notify you All, but Disk/Key This section allows you
Краткое содержание страницы № 19
CHAPTER 3 - BIOS SETUP CHAPTER 3 - BIOS SETUP No warning message will appear when Description Choice Disabled anything attempts to access the boot sector or hard disk partition table. Boot Up NumLock Status Description Choice Toggle between On or Off to control the state of the NumLock key when the system boots. When toggled On, the numeric keypad generates numbers instead of controlling cursor operations. CPU L1/L2 Cache ECC Checking When you select Enabled, memory checking
Краткое содержание страницы № 20
CHAPTER 3 - BIOS SETUP CHAPTER 3 - BIOS SETUP Description Choice 3.5 Advanced Chipset Features Setup Typematic Delay (Msec) When the typematic rate setting is enabled, you can select a typematic delay (the delay before key strokes begin to repeat) of 250, 500, 750 or 1000 milliseconds. Security Option Select whether the password is required every time the system boots or only when you enter setup. If you have set a password, select whether the password is required every time t
