Краткое содержание страницы № 1
DV50F9A6E(G)*
DV50F9A7E(G)*
DV50F9A8E(G)*
Gas and Electric Dryer
user manual
This manual is made with 100% recycled paper.
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service or accessory
parts, please register your product at or contact
www.samsung.com/register
1-800-SAMSUNG (726-7864)
Краткое содержание страницы № 2
features 1. Extra Large Capacity Ultra drying capabilities are at your fingertips! Now you can dry extra-large loads. Our ultra - large 7.4cu.ft capacity dryers circulate more air through your clothes, drying them faster, for a wrinkle-free result. 2. Steam Cycle This cycle sprays a small amount of water into the dryer drum after several minutes of tumbling with heat. It reduces bad odors from clothing that are difficult to remove when washing with water, and also reduces wrinkles. 3. Sanitize
Краткое содержание страницы № 3
8. Easy Reversible Door The direction of our reversible door can be changed easily. 9. 4-way Vent (electric model only) You can install the exhaust vent in the following four (4) positions: back, either side or bottom. 10. Smart Care This function diagnoses problems by itself. You don’t need to call a service engineer or try to find the user manual whenever the product has a problem, as Smart appliances let you know how to deal with the problem through your smart phone. Features _3
Краткое содержание страницы № 4
safety instructions Congratulations on your new Samsung Dryer. This manual contains valuable information on the installation, use, and care of your appliance. Please take the time to read this manual to take full advantage of your dryer’s many benefits and features. WhAT you nEED T o knoW AbouT SAFET y InSTRuCTIonS Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, cautio
Краткое содержание страницы № 5
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your WARNING appliance, follow basic precautions, including the following: 1. Read all instructions before using this appliance. 2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode. 3. Do not use the dryer to dry clothes which have tra
Краткое содержание страницы № 6
safety instructions WARNING - Risk of Fire • Clothes dr yer installation must be per formed by a qualified installer . • Install the clothes dr yer accor ding t o the manufactur er ’ s instructions and local codes. • Do not install a clothes dr yer with fle xible plastic venting mat erials. If fle xible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known
Краткое содержание страницы № 7
Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is necessary when the appliance is used near children and pets. Before discarding or removing your dryer from service, remove the door to the drying compartment to prevent children or animals from becoming trapped inside. Do not reach into the appliance when the drum is moving. Do not install or store this appliance where it will be exposed to the weather. Do not tamper with controls. Do not repair, r
Краткое содержание страницы № 8
contents 9 Unpacking your dr yer INsTAllING y OUR dRyeR 9 Basic r equirments 10 Ducting r equir ements 9 11 Important to installer 11 L ocation consider ations 11 Alcove or closet installation 12 Mobile home installation 12 Exhausting 13 Gas r equir ements 13 Commonwealth of Massachusetts installation instructions 14 Electrical r equir ements 14 Gr ounding 15 Electrical connections 16 Installation - General procedure 19 Final installation checklist 20 Vent blockage test 21 Dr yer
Краткое содержание страницы № 9
01 installing your dryer installing your dryer unp ACkInG youR DR yER Unpack your dryer and Inspect it for shipping damage. Make sure you have received all of the items shown below. If your dryer was damaged during shipping, or you do not have all of the items, contact 1-800-SAMSUNG (726-7864). To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the dryer. Packing materials can be dangerous to children. Keep all packing material (plastic bags, polystyrene
Краткое содержание страницы № 10
installing your dryer DuCTInG REquIREmEnTS • Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct. • Do not use a smaller duct. • Ducts larger than 4 inches (10.2 cm) in diameter can cause increased lint accumulation. Lint accumulation should be cleaned regularly. • If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct with a thin foil wall. Serious blockage can result if the flexible metal duct is bent too sh
Краткое содержание страницы № 11
01 installing your dryer If the new dryer is being installed into an existing exhaust system, you must make sure: • The exhaust system meets all local, state, and national codes. • That a flexible plastic duct is not used. • To Inspect and clean all lint buildup from inside the existing duct. • The duct is not kinked or crushed. • The exhaust hood damper opens and closes freely. The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be less than 0. This
Краткое содержание страницы № 12
installing your dryer mobILE homE InSTALLATIon The installation of the dryer in mobile homes must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR, Part 3280 {formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada). When installing a dryer in a mobile home, you must make provisions for anchoring the dryer to the floor. Locate the dryer in an area that has adequ
Краткое содержание страницы № 13
01 installing your dryer GAS REquIREmEnTS Use only natural or LP (liquid propane) gases. ThE InSTALLATIon muST ConFoRm WITh L oCAL CoDES, oR In ThE AbSEnCE oF L oCAL CoDES, WITh ThE nATIonAL FuEL GAS CoDE AnSI/Z223.1, LATEST REVISIon (FoR ThE unITED STATES), oR WITh ThE CAn/CGA-b149 InSTALLATIon CoDES (FoR CAnADA). Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP (liquid propane) gas, it must be converted for safe and proper performan
Краткое содержание страницы № 14
installing your dryer ELECTRICAL REquIREmEnTS The wiring diagram is located on the plate below the control panel or frame back. • Improperly connecting the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is WARNING properly grounded. Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician. • To p
Краткое содержание страницы № 15
01 installing your dryer ELECTRICAL ConnECTIonS Before operating or testing, follow all grounding instructions in the grounding section. An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN EXTENSION CORD. Gas models – U.S. and Canada A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is required. Electric models – U.S. only Most U.S. dryers require a 120 / 240 volt, 60 Hz AC approved electrical service. Some
Краткое содержание страницы № 16
installing your dryer InSTALLATIon - GEnERAL pRoCEDuRE For proper installation, we recommend that you hire a qualified installer. Read these instructions completely before you begin the installation. To install the dryer, follow these steps: 1. Move your dryer to an appropriate location for installation. Consider installing the dryer and washer side- by-side so you have easy access to both appliances. To move the dryer easily, lay two of the carton cushion-tops on the floor. Tip your dryer on it
Краткое содержание страницы № 17
01 installing your dryer 6. Review the Electrical Requirements section, then follow the 3 Wire system connection instructions (Step 7) or 4 Wire system instructions (Step 8) below. 7. Three Wire system instructions: A. External ground connector b. Neutral grounding wire (green/yellow) C. Center silver-colored terminal block screw d. Neutral wire (white or center wire) e. ¾” (1.9 cm) UL-listed strain relief 1. Loosen or remove the center terminal block screw. 2. Connect the neutral wire (white
Краткое содержание страницы № 18
installing your dryer u.S. moDELS: Risk Of Electric Shock WARNING All U.S.models are designed for a 3-WIRE SYSTEM CONNECTION. The dryer frame is grounded to the neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral. If you use the 4-wire system, you cannot ground the dryer frame to the neutral conductor at the terminal block. Remove the terminal block cover pla
Краткое содержание страницы № 19
01 installing your dryer ConnECTInG ThE InLET hoSE mEThoD1 The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. 1. If space permits, attach the brass female end of the “Y” connector to the cold water faucet. 2. Turn the cold water faucet off. 3. Attach the straight end of long hose to “Y’ connector. 4. Using pliers, tighten the coupling with an additional two-thirds turn. Do not overtighten, as it may damage the coupling. 5. Attach angled
Краткое содержание страницы № 20
installing your dryer VEnT bL oCkAGE TEST (DV50F9A7E(G)*,DV50F9A6E(G)*) After the dryer is installed, start the Test to check if the exhaust system is applicable for the dryer. Vent Blockage Test detects duct state of the dryer automatically and report blockage state of the duct to the user. Proper duct state can help users to reduce drying time and save energy. Vent Blockage Test must run at cool state. If it warms up after installation check, Run the Air fluff cycle for several minutes, so
