Краткое содержание страницы № 1
DV476*
DV484*
Gas and Electric Dryer
user manual
This manual is made with 100% recycled paper.
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service or accessory
parts, please register your product at or contact
www.samsung.com/register
1-800-SAMSUNG (726-7864)
DVDV476_484_03022E-01_EN_20120710.indd 1 DVDV476_484_03022E-01_EN_20120710.indd 1 2 2012-07-10 5:27:13 012-07-10 5:27:13
Краткое содержание страницы № 2
features 1. Extra Large Capacity Ultra drying capabilities are at your fingertips! Now you can dry extra-large loads. Our ultralarge 7.4cu.ft capacity dryer circulates more air through your clothes, drying them faster, for a wrinkle-free result. 2. Steam Cycle This cycle sprays a small amount of water into the dryer drum after several minutes of tumbling with heat. It reduces bad odors from clothing that are difficult to remove when washing with water, and also reduces wrinkles. 3. Sanitize
Краткое содержание страницы № 3
7. Easy Reversible Door The direction of our reversible door can be changed easily. 8. 4-way Vent (electric model only) You can install the exhaust vent in the following four (4) positions: back, either side, bottom. Features _3 D DVDV476_484_03022E-01_EN_20120710.indd Sec9:3 VDV476_484_03022E-01_EN_20120710.indd Sec9:3 2 2012-07-10 5:27:21 012-07-10 5:27:21
Краткое содержание страницы № 4
safety instructions Congratulations on your new Samsung Dryer. This manual contains valuable information on the installation, use, and care of your appliance. Please take the time to read this manual to take full advantage of your dryer’s many benefits and features. WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution,
Краткое содержание страницы № 5
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your WARNING appliance, follow basic precautions, including the following: 1. Read all instructions before using this appliance. 2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode. 3. Do not use the dryer to dry clothes which have tra
Краткое содержание страницы № 6
safety instructions WARNING - Risk of Fire � Clothes dryer installation must be performed by a qualified installer. � Install the clothes dryer according to the manufacturer’s instructions and local codes. � Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be e
Краткое содержание страницы № 7
Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is necessary when the appliance is used near children and pets. Before discarding or removing your dryer from service, remove the door to the drying compartment to prevent children or animals from becoming trapped inside. Do not reach into the appliance when the drum is moving. Do not install or store this appliance where it will be exposed to the weather. Do not tamper with controls. Do not repair, r
Краткое содержание страницы № 8
contents 9 Unpacking your dryer INSTALLING YOUR DRYER 10 Basic requirments 11 Ducting requirements 9 12 Important to installer 12 Location considerations 12 Alcove or closet installation 13 Mobile home installation 13 Exhausting 14 Gas requirements 14 Commonwealth of Massachusetts installation instructions 15 Electrical requirements 15 Grounding 16 Electrical connections 17 Installation - General procedure 19 Final installation checklist 20 Connecting the inlet hose 22 Dryer Ex
Краткое содержание страницы № 9
01 installing your dryer installing your dryer UNPACKING YOUR DRYER Unpack your Dryer and inspect it for shipping damage. Make sure you have received all of the items shown below. If your Dryer was damaged during shipping, or you do not have all of the items, contact 1-800-SAMSUNG (726-7864). To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the dryer. Packing materials can be dangerous to children. Keep all packing material (plastic bags, polystyrene,
Краткое содержание страницы № 10
installing your dryer Tools needed Pipe wrench Pliers Cutting knife Nut drivers (gas only) Level Phillips Screwdriver Duct tape Wrench BASIC REQUIRMENTS Make sure you have everything necessary for proper installation � A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements. � A POWER CORD for electric dryers (except in Canada). � GAS LINES (if installing a gas dryer). The gas lines must meet national and local codes. � EXHAUST SYSTEM - must be rigid metal or flexible stiff-walled
Краткое содержание страницы № 11
01 installing your dryer DUCTING REQUIREMENTS � Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct. � Do not use a smaller duct. � Ducts larger than 4 inches (10.2 cm) in diameter can cause increased lint accumulation. Lint accumulation should be cleaned regularly. � If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct with a thin foil wall. Serious blockage can result if the flexible metal duct is bent too sha
Краткое содержание страницы № 12
installing your dryer If the new dryer is being installed into an existing exhaust system, you must make sure: � The exhaust system meets all local, state, and national codes. � That a flexible plastic duct is not used. � To Inspect and clean all lint buildup from inside the existing duct. � The duct is not kinked or crushed. � The exhaust hood damper opens and closes freely. The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be less than 0. This can be m
Краткое содержание страницы № 13
01 installing your dryer MOBILE HOME INSTALLATION The installation of the dryer in mobile homes must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR, Part 3280 {formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada). When installing a dryer in a mobile home, you must make provisions for anchoring the dryer to the floor. Locate the dryer in an area that has a
Краткое содержание страницы № 14
installing your dryer GAS REQUIREMENTS Use only natural or LP (liquid propane) gases. THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA). Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP (liquid propane) gas, it must be converted for safe and proper performance by
Краткое содержание страницы № 15
01 installing your dryer ELECTRICAL REQUIREMENTS Wiring diagram is located on the plate below the control panel or frame back. � Improper connection of the equipment grounding conductor can result in a risk of electric shock. WARNING Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly grounded. Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician. � To pre
Краткое содержание страницы № 16
installing your dryer ELECTRICAL CONNECTIONS Before operating or testing, follow all grounding instructions in the Grounding section. An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN EXTENSION CORD. Gas models – U.S. and Canada A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is required. Electric models – U.S. only Most U.S. dryers require a 120 / 240 volt, 60 Hz AC approved electrical service. Some requ
Краткое содержание страницы № 17
01 installing your dryer INSTALLATION - GENERAL PROCEDURE For proper installation, we recommend that you hire a qualified installer. Read these instructions completely before you begin the installation. To install the dryer, follow these steps: 1. Move your dryer to an appropriate location for installation. Consider installing the dryer and washer side- by-side so you have easy access to both appliances. To move the dryer easily, lay two of the carton cushion-tops on the floor. Tip your dryer o
Краткое содержание страницы № 18
installing your dryer 6. Review the Electrical Requirements section, then follow the 3 Wire system connection instructions (Step 7) or 4 Wire system instructions (Step 8) below. 7. Three Wire system instructions: A. External ground connector B. Neutral grounding wire (green/yellow) C. Center silver-colored terminal block screw D. Neutral wire (white or center wire) E. ¾” (1.9 cm) UL-listed strain relief 1. Loosen or remove the center terminal block screw. 2. Connect the neutral wire (white or c
Краткое содержание страницы № 19
01 installing your dryer U.S. MODELS: IMPORTANT – All U.S. models are designed for a 3-WIRE SYSTEM CONNECTION. The dryer frame is grounded to the neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral. If you use the 4-wire system, you cannot ground the dryer frame to the neutral conductor at the terminal block. Remove the terminal block cover plate. Insert the
Краткое содержание страницы № 20
installing your dryer CONNECTING THE INLET HOSE Method1 - Using the Y Connector and Long Hose The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. 1. Turn off the cold water faucet. 2. If you have a washer water hose attached to the cold water Y-Connector faucet, unscrew and remove the hose. 3. If space permits, attach the brass female end of the “Y”connector to the cold water faucet. Turn by hand until tight. Water Hose 4. Attach the straight
