Краткое содержание страницы № 1
Краткое содержание страницы № 2
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. 1. Use only as described in this manual. Use only manufacturer’ s recommended attachments. 2. Use indoors only. Do not use outdoors and do not expose to rain. 3. Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near flammable f
Краткое содержание страницы № 3
THIS PRODUCT IS FOR COMMERCIAL USE WARNING: ONLY. ELECTRICAL: In the USA this machine operates on a standard 15 amp 115 volt A.C. power circuit (12OV nominal). Special voltage models are available for interna- tional applications. The amp, hertz and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors. EXTENSION CORDS: If an extension cord is used, the wire size must be the same type an
Краткое содержание страницы № 4
CONTROLS Solution Adjust brush to proper cleaning position by using Power Cord lever located on the front of the frame. Start at No. 1 “new brush” (black) position. If more carpet pile Vat intake Filter/Screen\ agitation is desired, lower brush setting one posi- tion at a time. (See fig. 1 below) Main Handle Fig. 1 4 Removable / Recoverv \ f- Switches (see below) Solution Tank, / -HIGH > Accessorv Tool Manifold/Jets Water Control Switch Brush Release Knob Brush Adiustment Solution Tank Filter/Sc
Краткое содержание страницы № 5
Preparing the SPIRIT DUAL: Filling Solution Tank: For Hard Floor: 1.) Set dome and recovery tank to the side. 1.) Install the optional kit : Vac Shoe Squeegee (p/n 02285). Raise the SPD vac shoe and place the squeegee assembly over the vac shoe intake. Center the squeegee 2.) Use a clean bucket to fill the solution tank on the vac shoe and secure by tightening the two retain- with hot water. ing knobs. CAUTION: Make sure that the machine is un- plugged, switches are turned off and both solution
Краткое содержание страницы № 6
SPIRIT 14. When solution tank empties the machine will start 1. Fill the solution tank. streaking and won’ t completely clean the floor. 2. Move machine to the cleaning area. Turn both switches off, empty the recovery tank, 3. Lower the brush housing to the floor. and refill the solution tank. Use the clear drain 4. Adjust the brush to the desired height. hose on the rear of the solution tank as a sight 5. Plug machine into electrical outlet. gage to determine amount of fluid in tank. 6. Release
Краткое содержание страницы № 7
15.) Ventilate the room when cleaning has Approved Accessory Tools: Standard Floor Wands been completed. Keep all traffic off the (SFW, SW, or SW-PRO) floor until it is thoroughly dry. Deluxe Hand Tool (DHT) 16.) When done cleaning for the day bring Upholstery Hand Tool (UPH3) the machine to a utility sink and floor drain. Perform the daily/regular Floor Surface Inspection: maintenance. Set the recovery tank Determine precisely what areas you are going to aside so solution tank will dry. clean.
Краткое содержание страницы № 8
Dailv Maintenance: WARNING OF These procedures are followed at the end of each work period to extend the life of the ma- POTENTIAL INJURY chine. Empty unused cleaning solution by 1.) This product contains moving parts. disconnecting clear hose on back of machine and pouring into floor drain. To reduce the risk of injury; unplug the machine before servicing. Inspect and clean solution filter screen 2.) inside tank and vac intake screen inside dome. Maintenance and repairs must be done by qualifie
Краткое содержание страницы № 9
Periodic Maintenance: CAUTION: These procedures are performed by a Do not allow this machine to remain in a trained service technician. The regularity of vehicle or area where the temperature these procedures may depend on the ma- will be below 40°F (4°C). Allowing this chine's use. machine to freeze will cause damage not covered by the 6-3-1 warranty. Flush the system with a special 1.) solution to reduce scaling (alkaline build-up). CAUTION: Protect this machine from freezing if it Use acetic
Краткое содержание страницы № 10
Troubleshooting Chart - Corrective Action Condition No Power To Machine: Check building circuit breaker. Dead electrical circuit breaker in fuse box Faulty power cord Replace Test switch for continuity/Replace if necessary. Power switch failure Test circuit breaker for continuity/Replace if necessary. Faulty circuit breaker With the machine unplugged, check for, and correct, any loose wire Internal wiring problem connections inside the machine at the switches and terminal block. Electrical Shock
Краткое содержание страницы № 11
Troubleshooting Chart Corrective Action Condition Accessory Tool Fitting Difficult to Connect: Clean with steel wool. Corrosion on fitting Remove and soak in acetic acid (white vinegar). Lubricate lightly with silicone base lubricant. Floor Not Getting Clean: Make several passes at right angles to each other. Severe soil conditions Use a prespray. Floor Too Wet: Replace spray jets which are producing more than a fine mist. Worn spray jet(s) Floor Not Getting Wet: Clean solution filter screen loc
Краткое содержание страницы № 12
Servicing the Vac Motor To access the vac motor first remove the solution tank. There are (2) screws which attach the vac motor mounting bracket to the chassis. Loosen the clamp to remove the hose. To replace the motor assembly it will be necessary to remove the (3) screws which attach the motor to the vac motor mounting bracket. See page 18 for the complete vac motor and mounting equipment parts list. Wire Important: These brushes wear quicker as the length shortens due to in- creased heat. Spr
Краткое содержание страницы № 13
Vac Shoe Assembly 6 Assembly Reverse 57047 Nut, l/4-20 Nylock 87074 Washer, 3/8 ID x .OlO Wave 05016 Arm, Vac Shoe Parallel 73181 Spacer, .259 ID x .38x .25 70190 Scr, l/4-20 x 1/2 BHCS 70057 Scr, l/4-20 x 1 .O PHMS 89061 Weight, Vat shoe 87008 Washer. l/4 ID x 1 l/4 OD 10 87016 Washer: #10 star 11 70088 Scr, lo-32 x l/2 PHMS 96353 7/l/97 13
Краткое содержание страницы № 14
RECOVERY & SOLUTION TANKS RECOVERY TANK Each tank has a filter screen which protects the machine’ s internal parts from damage. Ensure that these screens are in place and clean before operating the machine. SOLUTION TANK 14 SPD 98353 8/10/98
Краткое содержание страницы № 15
RECOVERY & TANK ASSEMBLY Parts List RECOVERY TANK PARTS LIST; 2 87013 Washer, l/4 Flat 3 73280 Spacer, 1/4 ID x 3/8 Nylon 4 38088 Handle, Recovery Tank 5 75078 Tank, Recovery 6 14042 Bushing, 1.63 ID Snap 7 39343 Hose, 1.5 x 34” Vac 8 39411 Hose, 1.5 x 52” Vac 9 27079 Cuff, White 1.5 Hose 10 27508 Cuff, Short Blue Hose 11 27354 Hose cuff, blue 12 28033 Dome Asm 13 50775 Label, Warning Explosion Vert 14 50776 Label, Warning For Safety SOLUTION TANK PARTS LIST: 2 - Open 3 39241 Hose, l/2 Wire Boun
Краткое содержание страницы № 16
Pump...Manifold...VaIve Spray Jets Rinse in hot water or use compressed air to clean. Nozzles can also be soaked in an acetic acid solution (white vinegar). CAUTION: Do not use pins or wires to clean or unclog jets. 6 Using wires or pins to unclog jets may ruin spray pattern. ‘ 23 24 26 Replace jets that no longer produce a fine mist spray or over saturate carpet. 16 96353 7/l/97
Краткое содержание страницы № 17
Pump...Manifold...VaIve 04008 Adaptor, .1/4 MPT x l/4 FPT 56023 Nipple, l/4 MPT x 1.5 Tee, l/4 FPT 78156 56014 Nipple, l/4 Close 65154 Pump, 115V 50 PSI OPEN 70253 Screw, 10-32 x 1.25 PHMS Nut, 10-32 Captive J 57081 Hosebarb, l/4 MPT x 3/8 90” 40033 27665 Cable, Solution SPD 12 70088 Scr, 10-32 x l/2 PHMS 13 84134 Valve, Solution 14 31016 Elbow, l/4 NPT Street 15 40038 Hosebarb, 45 deg 1/4MPT x 3, 16 20042 Clamp. Hose 17 39452 Hose: 3/8 x 6” Nylobraid 18 70114 Scr, #1 0 x 3/4 Polyfast 19 14523 B
Краткое содержание страницы № 18
HANDLE...CHASSIS...SWITCHES Ground Arrangement Vac, Brush & Pump motor ground wires See page 4 for panel configuration 18 SPD 98353 9/18/98
Краткое содержание страницы № 19
HANDLE,..CHASSIS...SWITCHES Parts List 2 57104 Nut, 10-32 w/Star Washer 3 Open 4 89114 Wheel, 10” 602252 5 41236 Hub Cap, Y8” Shaft 6 70249 Scr, l/4-20 x 1.25 HHMS 7 73636 Spacer, 5/16 x 1.2” 8 73596 Spacer, 5/16 x 1” 9 51193 Linkage, Handle Adjustment 10 38269 Handle, SPD II 11 41302 Housing, Solution Lever 12 57047 Nut, l/4-20 Nylock 13 36123 Grip, 9.5” Handle 14 41144 Hook, Cord 15 70361 Scr, 10-32 X l/2 PHTR 16 57238 Nut, 10-24 Joint Connector 17 51251 Lever, Solution 18 27561 Clip, Solution
Краткое содержание страницы № 20
BRUSH DRIVE ASSEMBLY To access the belt remove the belt cover. To replace the belt it is necessary to loosen the motor and remove the brush. The “preset” belt tension is correct when the motor and belt are securely back in place. Check pulley alignment and correct if necessary. The brush pulley and motor pulley can be aligned using a straight edge. Ensure that both protective covers are back in place before operating the machine. SPD 98353 7/l/97
