Краткое содержание страницы № 1
1
LOG BOOK
: Age: Weight: kg/lbs
2 21.2 22.2
10:05 10:12
mmHg
220
200
180
160
x
x
140
120
x
x
100
x
x
80
60
/ min 85 90
158 155
92 93
110 112
1
GB
Краткое содержание страницы № 2
GB LEGEND : - FAST INCREMENT - FLASHING BOLD - PRESS BUTTON BOLD - PRESS AND HOLD BUTTON F LEGENDE : - AUGMENTATON RAPIDE - CLIGNOTEMENT - APPUYER SUR LE BOUTON BOLD BOLD - APPUYER SANS LACHER SUR LE BOUTON ES LEYENDA : - INCREMENTO RÁPIDO - DESTELLANDO BOLD - PULSAR BOTÓN BOLD - PULSAR MANTENER OPRIMIDO EL BOTÓN 2 GB
Краткое содержание страницы № 3
WRIST TYPE BLOOD PRESSURE INFORMATION CONCERNING THE CE MONITOR SYMBOL This device complies with the European regulations based on the MODEL: BPW128 Medical Products Code, and bears the CE mark “CE0123”. The device has been quality inspected according to EG guideline USER’S MANUAL 93/42/EWG and tested in compliance to the EN1060-1 Non-invasive sphygmomanometers-Part 1, General requirements and EN1060-3 Non-invasive sphygmomanometers-Part 3: INTRODUCTION Supplementary requirements for electrome
Краткое содержание страницы № 4
DESCRIPTION AND FUNCTION OF PARTS F A A. Liquid Crystal Display (LCD) and protective cover - Large easy-reading display - 5 functional symbols E - Systolic [SYS/mmHg], Diastolic [DIA/mmHg], Mean [MAP/mmHg], Pulse [pul/min.]and date & time display. C B. Battery compartment D Houses two (2) LR03 /AAA/ UM4 size 1.5V batteries C. Button - For time adjustment. B D. Button - Activates and deactivates the unit and initiates pressure measuement process. ▲ ▲ E. / ▲ ▲ ▲ Button - Recall memory or increa
Краткое содержание страницы № 5
AAA AAA DISPLAY-SYMBOL DESCRIPTION INSTALLING BATTERIES 1. Slide battery cover off. 2. Install batteries first. Ensure Symbol Description Explanation correct polarity. Battery Type: 2 Alkaline LR03 (AAA)size Appears when Memory Mark measurement value is 3. Replace the cover. recalled from memory Replace the batteries if: 1. the weak battery mark appears Appears when batteries Weak Battery should be replaced in the display 2. nothing appears in the display when the power is switched on. Appears
Краткое содержание страницы № 6
PROPER EQUIPMENT SETUP 1. Remove all watches, jewelry, etc. prior to attaching the wrist monitor. Clothing sleeves should be rolled up and the cuff should be wrapped on bare skin for correct measurements. 2. Apply cuff to left wrist with palm facing up. 3. Make sure the edge of the cuff is about 1 cm from the plam. 4. In order to ensure accurate measurements, fasten the velcro strap securely around your wrist so there is no extra space between the cuff and the wrist. If the cuff is not wrapped
Краткое содержание страницы № 7
BLOOD PRESURE DEFINITIONS WHAT IS MEAN ARTERIAL PRESSURE (MAP) Information obtained from the World Health Organization (WHO) The Mean Arterial Pressure is the average pressure forcing blood through the arteries. It is not the average of the systolic and diastolic Hypertension systolic over 160 blood pressure. It corresponds to a state of balance between the (high pressure) diastolic over 95 compressive and expansive forces acting on the arterial wall when 95 there is no distension of the arteria
Краткое содержание страницы № 8
MEASUREMENT With the individual in a sitting position and with the cuff attached as previously mentioned, a blood pressure reading can be obtained. Note: - For accurate pressure measurement, take blood-pressure readings in a seated position. Avoid leaning back while the measurement is being taken. - Ensure that the lower arm is raised so that the upper edge of the cuff is on the same level as the heart. - Ideally, place the palm of the hand facing upwards. - In order to ensure a proper measureme
Краткое содержание страницы № 9
HOW TO TAKE MEASUREMENT Refer to Fig1 Fig1 2sec Fig1 9 GB
Краткое содержание страницы № 10
Note: 1. Remove all watches, jewelry, etc. prior to attaching the wrist 2sec monitor. Clothing sleeves should be rolled up and the cuff should be wrapped on bare skin for correct measurements. 2. Apply cuff to left wrist with palm facing up. 3. Make sure the edge of the cuff is about 1 cm from the plam. 4. In order to ensure accurate measurements, fasten the velcro strap securely around your wrist so there is no extra space between the cuff and the wrist. If the cuff is not wrapped tight enough,
Краткое содержание страницы № 11
HOW TO SET THE TIME Refer to Fig3 mode Fig 3 11 GB
Краткое содержание страницы № 12
Note: AUTOMATIC POWER OFF 1. Press and hold the [ ]button for 2 seconds, the display will flash 12h or 24h. The device will automatically switch off after about 1 minute. However, to conserve battery power, press the button when 2. Press the [ ▲ ▲ ▲ ▲ ▲ ] button to select either 12 hour or 24 hour display. finished to turn the unit off. 3. Press the [ ] button to accept 4. The hour digits will flash. Press the [ ▲ ▲ ▲ ▲ ▲ ] button to set the hour 5. Press the [ ] button to accept ERROR ME
Краткое содержание страницы № 13
MAINTENANCE, CLEANING AND CARE SPECIFICATIONS When handled properly, this unit is engineered to give years of Measuring method : Oscillometric / non-invasive satisfactory service. Application : Adults Here are a few product care instructions: Measurement location : Wrist section of lower arm - When not in use, store the unit in the protective plastic container Circumference (approx. ) provided with your purchase. 5.3"-7.7"(13.5-19.5cm) - Do not immerse the unit in water. If the unit comes in con
Краткое содержание страницы № 14
Should you require assistance regarding this product and its operation, SYMBOL DESCRIPTIONS please contact our Customer Care Department at 1-800-853-8883 or via email at helpme@oscientific.com. Please observe user’s manual ! WARRANTY Protection class BF This product is warranted to be free of manufacturing defects for a period of 12 months from date of retail purchase. Defective product DC (Direct current) should be directed to the place of retail purchase for exchange. Should this not be possib
Краткое содержание страницы № 15
measurement again, ensure that the cuff is properly attached, the arm is in the proper position and that movement has been minimized during the measurement process. If the device does not function: - Check that the unit is on. After about 3 minutes of inactivity, the unit will automatically turn off. - Ensure that batteries are properly inserted. Batteries may be exhausted and require replacement. A battery-low indicator [ ] will display to indicate that batteries are low and need changing. Mea