Руководство по эксплуатации Magnadyne 4900 Series

Краткое содержание страницы № 1

4900-UM.qxp 5/11/06 2:31 PM Page 1
OWNER’S
MANUAL
Models: 4900 Series
4960 Series
Vehicle Immobilizers
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference; and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to
th

Краткое содержание страницы № 2

4900-UM.qxp 5/11/06 2:31 PM Page 2 Silencer products have been designed to provide the consumer with years of trouble-free operation. This manual will provide reference for the operation and maintenance of your new Silencer vehicle immobilizer system. Please, take a moment to read this manual so you will be familiar with the opera- tion of your new system. Valet Disarm On Valet Off 1-Button Automatic 3-Button Transmitter 1-Button Transmitter Disarm Transmitter Note: Depending on the type o

Краткое содержание страницы № 3

4900-UM.qxp 5/11/06 2:31 PM Page 3 Radio Frequency (RF) Protection Rearm Timer Each time the system is disarmed using the transmitter the device will begin a protection mode countdown. This is a timed secondary protection mode. If you do not start your vehicle within 60 seconds, your Silencer system will become rearmed and your engine will become disabled again. Note: If your system operates from a “Automatic Disarm Transmitter”, the 60 second RF protection timer will not time-out and will re

Краткое содержание страницы № 4

4900-UM.qxp 5/11/06 2:31 PM Page 4 Valet Mode 3-Button Transmitter The Valet Mode allows you to temporarily turn off the passive arming function, eliminating the need to give your transmitter to a parking attendant or garage mechanic. To enter the Valet Mode, follow these steps: 1. Press the “Disarm” button on your transmitter to insure the device is disarmed (you will hear 2 beeps). 2. Within 3 seconds of pressing the disarm button, press and release the “Valet On” button 3 times slowly.

Краткое содержание страницы № 5

4900-UM.qxp 5/11/06 2:31 PM Page 5 Emergency Override There may come a time when it will be necessary to manually disarm your Silencer system without using your transmitter. This condition occurs if the battery in your transmitter is low, dead or if your transmitter becomes damaged or lost. Under these circumstances, it will be necessary to use your igni- tion key to perform an emergency override procedure to get your vehicle operational. Identify your Silencer model type and repeat the proce

Краткое содержание страницы № 6

4900-UM.qxp 5/11/06 2:31 PM Page 6 Emergency Override 4960 Series 1. Turn the ignition key to the "Crank" position, then turn the key off. Repeat this procedure 1 more time. 2. Wait for 10 seconds 3. Turn the ignition key to the "Crank" position, then turn the key off. Repeat this procedure 1 more time. 4. Wait for 10 seconds 5. Turn the ignition key to the "Crank" position, then turn the key off. Repeat this procedure 1 more time and the engine will start. Note 1: For vehicles with manual

Краткое содержание страницы № 7

4900-UM.qxp 5/11/06 2:31 PM Page 7 System Maintenance The only maintenance that your Silencer vehicle immobilizer requires is a periodic check to insure that all operations are functioning normally. This is also good practice for you to refresh your mem- ory on “Emergency Override” and “Valet Mode” procedures. Batteries 1-Button and 3-Button Manual Disarm Transmitters The battery supplied with the 1-button and 3-button transmitters has an average life of 1 year. Heavy transmitter usage will

Краткое содержание страницы № 8

4900-UM.qxp 5/11/06 2:31 PM Page 8 3 Year Warranty ® ® Your new Silencer Security Systems is warranted to be free of defects for 3 years. Silencer or its authorized agents will within 3 years from the date of sale to you, repair or replace said ® product or any part thereof, at the option of the Silencer or its authorized agents, if said prod- uct or part is found defective in materials or workmanship, when properly connected and oper- ating on the correct power requirements designated for th