Руководство по эксплуатации Aiwa XP-R120

Краткое содержание страницы № 1

Highlighted letters in the text of this manual correspond to the illustrations.
PRECAUTIONS
To maintain good performance
• Do not use the unit in places which are extremely hot, cold, dusty or humid. In
particular, do not use or keep the unit in following places.
• in a high humidity area such as a bathroom
XP-R120
• near a heater
• in an area exposed to direct sunlight (e.g., inside a parked car, where it can
COMPACT DISC PLAYER
become extremely hot)
• near sources of strong magnetism, such as

Краткое содержание страницы № 2

If the lens becomes dirty, the player will skip or not play. If this occurs, clean the lens in the following manner. To remove dust or dry particles, first use a camera lens blower/brush a to blow a few times to loosen particles, then gently brush the lens b clean. Finish by blowing the lens again. A To remove fingerprints, use a cotton swab dipped in lens cleaning solution. Wipe gently from the center to the edge. Lens cleaning solution is commercially available. Note Take care not to get too m

Краткое содержание страницы № 3

USING ON RECHARGEABLE BATTERIES → E 12 E You can use on rechargeable batteries, which you charge using an AC adaptor. Rechargeable batteries and an AC adaptor are commercially available. • Be sure to use size AA Ni-Cd 1.2 V 700 mAh rechargeable batteries. • Be sure to use an AC adaptor whose rated output is DC 5 – 6 V, 250 – 300 mA. • Be sure to read instructions of the purchased AC adaptor and rechargeable batteries before use. • When using on rechargeable batteries for the first time, charge t

Краткое содержание страницы № 4

G USING ON AC HOUSE CURRENT Use only an AC adaptor whose rated output is DC 5 – 6 V, 250 – 300 mA. DSL Connect the AC adaptor in the same way as when recharging the batteries. During operation on AC house current, all of the battery indicator disappears. BEFORE PLAYBACK HOLD switch → F Release the HOLD switch before playback. → a When not using the unit, set the HOLD switch to the HOLD position. → b Accidentally pressed button will not function. If buttons are pressed when the HOLD switch is set

Краткое содержание страницы № 5

PLAYBACK → J J Connect the supplied headphones to the PHONES/LINE OUT jack. The amplified speaker system can be connected instead to enjoy the CD sound. 1 Release HOLD. 2 Place a disc. 3 Press ePLAY/PAUSE. Playback starts from the first track. a track number b elapsed playing time Basic operation To stop Press sSTOP/OFF/CHARGE. To pause Press ePLAY/PAUSE. To resume, press it again. 12 To search for the beginning of a track Press r or t. To locate a desired passage Keep r or t pressed. Release th

Краткое содержание страницы № 6

completely (ideally about 20 seconds). Continuous shock or vibration may cause the sound to be interrupted even if the E•A•S•S 2× function is activated. This is normal and not a malfunction. Should you experience an interruption in sound, stabilize the unit for a few seconds, then resume your activity. • When the E•A•S•S 2× function is activated, motor noise is heard as the motor periodically rotates at high speed during playback. This is not a malfunction. • When the E•A•S•S switch is slid duri

Краткое содержание страницы № 7

RADIO RECEPTION O Tuning in to a station → O 1 Press BAND TUNER ON repeatedly to select AM or FM. 2 Press TUNING + (t) or - (r) to tune in to a station. After listening, press sSTOP/OFF/CHARGE to turn off the radio. For better reception → P FM: The headphone cord functions as the FM antenna. Keep it extended. AM: Turn the unit to find the position which gives the best reception. To listen to an FM stereo broadcasting When a tuned in station is in stereo, ST changes to . BAND 1 When the FM ste

Краткое содержание страницы № 8

To preset more stations, re eat ste s 2 and 3. Listening to preset stations → S 1 Press BAND TUNER ON repeatedly to select AM or FM. 2 Press PRESET CALL UP/DOWN repeatedly to select the preset number. After listening, press sSTOP/OFF/CHARGE to turn off the radio. R Changing the presetting 1 Press PRESET CALL UP/DOWN repeatedly to select the preset number you wish to change. 2 Keep ENTER/DISP pressed for 1 or more seconds until the preset number and the frequency flash. 3 While the preset number