Краткое содержание страницы № 1
HUFFY HUFFY
SPORTS SPORTS
Portable System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
WARNING!
REQUIRED TOOLS AND MATERIALS:
• Two People
• Tape Measure
READ AND UNDERSTAND
• Wood Board (Scrap)
OPERATOR'S MANUAL
• Wrenches: (Two) 7/16”, 1/2”, 9/16”, 3/4” or Large and Small
Adjustable Wrenches
BEFORE USING THIS UNIT.
• Sawhorse or Support Table
• Step Ladder 8 ft. (2.4 m)
FAILURE TO FOLLOW
• Garden Hose or Sand (225 lb.) (102 kg)
• Hammer
Краткое содержание страницы № 2
BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. AVANT DE COMMENCER ! Pour garantir l'utilisation optimale du panneau, les composants du système élévateur et la visserie doivent être bien ajustés (serrés). À
Краткое содержание страницы № 3
WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury could occur if teeth/face come in contact with backboard, rim or net.
Краткое содержание страницы № 4
NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to the instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. WARRANTY CARD: Please remember to complete your product registration fo
Краткое содержание страницы № 5
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk of accident or injury. A high probability of serious injury
Краткое содержание страницы № 6
SPORTS SPORTS H HUFFY UFFY Get to know the basic parts of your basketball system..... FRONT BACKBOARD RIM ELEVATOR SYSTEM POLE SUPPORT STRUT BASE WHEELS 6 P/N 211953C 12/03
Краткое содержание страницы № 7
PARTS LIST - See Hardware Identifier PARTS LIST - See Hardware Identifier Item Qty.Part No. Description 1 1 206336 Tank, (Gray) 2 2 206330 Wheel Axle, 4-1/4 Long 3 2 226401 Wheel, 4 “ (Black) 4 1 904847 Top Pole Section 5 1 908481 Middle Pole Section 6 1 908487 Bottom Pole Section 7 1 202820 Rod, 3/8 O.D. x 4-3/4 Long 8 1 202822 Eyebolt, 3/8-16 x 3-3/4 Long 9 1 202821 Disk, 2-3/4 Diameter 10 1 203063 Nylon Insert Lock Nut, 3/8-16 11 2 906410 Strut, 1” O.D. x 43 Long 12 1 203220 Nut, Nylock, 5/1
Краткое содержание страницы № 8
HARDWARE IDENTIFIER (BOLTS) Item #8 (1) Item #31 (1) Item #18 (2) Item #37 (1) Item #25 (3) Item #47 (6) Item #21 (3) Item #30 (2) Item #48 (1) Item #15 (2) Item #14 (1) * You may have extra parts with this model. 8 P/N 211953C 12/03
Краткое содержание страницы № 9
HARDWARE IDENTIFIER (NUTS & WASHERS) Item #20 (3) Item #39 (7) Item #35 (1) Item #10 (1) Item #12 (1) Item #13 (7) Item #9 (1) Item #16 (11) Item #19 (4) HARDWARE IDENTIFIER (STEEL SPACERS & RODS) Item #2 (2) Item #36 (2) Item #23 (2) Item #7 (1) HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS) Item #38 (6) Item #44 (4) Item #22 (2) Item #55 (6) Item #56 (4) Item #50 (12) * You may have extra parts with this model. (Not Actual Size) 9 12/03 P/N 211953C
Краткое содержание страницы № 10
SECTION A: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: HARDWARE USED IN THIS SECTION TOOLS REQUIRED FOR THIS SECTION (not actual size) (2) 1/2” AND (2) 9/16" Wrenches Item #20 Item #8 Item #31 Item #13 Item #10 Item #22 AND/OR Item #19 (2) Socket Wrenches and Sockets Item #12 Item #9 (1) Item #16 Item #23 Item #18 Item #21 Item #25 Item #14 1/2” 9/16” Item #30 Item #2 Item #15 Item #7 10 P/N 211953C 12/03
Краткое содержание страницы № 11
Remove all contents from underside of 1 tank. Keep tank (1) bottom side up 1. Insert axle rod (2) through wheel (3), as shown. Secure wheel assembly to tank (1) by tapping 2. 3 wheel downward with hammer, snapping it into position. Repeat for opposite side, then carefully, turn tank (1) over. 2 1 Mark pole sections with tape as shown. 3. 5 TAPE (not included) 4 6 11 12/03 P/N 211953C
Краткое содержание страницы № 12
IMPORTANT! Center alignment slot of middle pole section (5) in a lower hole of 4. top pole section (4) as shown. While maintaining alignment, bounce middle pole (5) 5 into top pole section (4) as shown until top pole section no longer moves toward taped reference mark on middle pole. Upright assembly. NOTE: POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) 4 MINIMUM OVERLAP. WOOD SCRAP (NOT SUPPLIED) IMPORTANT! Center alignment slot of lower pole 5. section (6) in a lower hole of middle pole section (
Краткое содержание страницы № 13
Install rod (7) through holes in bottom pole 7 section (6) and eyebolt (8). 6. 4 5 6 8 Insert pole assembly into tank assembly as shown. 6 7. WARNING! 7 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT 8 IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. IMPORTANT!: DO NOT OVER TIGHTEN Carefully place unit on its side. Secure pole bottom (6) to tank with anchor strap (52), 8. washers (9 & 13) and nut (10) as shown. Upright unit. NOTE: 9 6 13 Keep unnecessary pressure
Краткое содержание страницы № 14
SPORTS SPORTS HUFFY HUFFY Secure strut tubes (11) to bottom pole section (6) as shown. 9. 11 WARNING! 6 13 14 12 13 11 TIGHTEN BOLT (14) IN 1 LOCK NUT (12) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. Install pole mount bracket (17) with carriage bolts (18) as shown. 10. 11. Tighten flange nuts (16) completely. Once again, carefully place unit in the side position and secure strut (11) to tank (1) as shown. Completely tighten. Repeat for opposite side. Upright unit. NOTE: Keep unnecessary
Краткое содержание страницы № 15
Attach spacers (22, 23) to pole mount bracket (17) with bolts (21), washers (19), and nuts (20) as shown. 12. IMPORTANT!: Tighten just until washers (19) stop moving. 17 22 20 19 23 20 19 21 19 23 19 22 21 Assemble lanyard (27) to locking pin (26) as shown (FIG A). Attach covers (24) onto pole mount bracket (17) with carriage bolt (25) and nut (16) as shown. 13. FIG. A 24 16 17 24 IMPORTANT!: 25 25 Loop end of pin lanyard (27) over 27 carriage bolt (25) as it passes 27 through the pole mount bra
Краткое содержание страницы № 16
Apply logo and height indicator labels (29) to adjustment rod (28) as shown. Attach handle 14. 15. parts (32, 33) to adjustment rod with screw (31), carriage bolt (30), and flange nut (16) as Insert handle assembly through pole shown. mount assembly as shown. Lock pole assembly in place at the 10’ IMPORTANT!: (3.05 m) mark with pin (26). Indicator labels should be applied as close to holes as possible to prevent labels from being damaged during height adjustment. 28 26 29 28 16 33 30 16 31 32
Краткое содержание страницы № 17
HUFFY HUFFY SPORTS SECTION B: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: HARDWARE USED IN THIS SECTION TOOLS REQUIRED FOR THIS SECTION (not actual size) (2) 1/2”, (2) 9/16" AND (2) 3/4" Wrenches Item #37 Item #35 Item #56 Item #16 AND/OR Item #50 (2) Socket Wrenches and Sockets Item #39 Item #21 Item #47 Item #48 3/4” 1/2” 9/16” Item #20 Item #38 Item #44 Item #55 17 12/03 P/N 211953C
Краткое содержание страницы № 18
Install spacers (36) onto backboard brackets (34) with bolts (37, 21) and lock-nuts (35, 20) as shown. 16. 35 20 36 37 21 34 Assemble lower elevator tubes (40) as shown. NOTE: Test fit bolts into holes of brackets (34) and carefully rock them in a circular 17. motion to ream out paint from holes if necessary 39 55 34 40 IMPORTANT!: 47 Refer to instructions included with board and rim hardware for backboard and 55 rim assembly. 41 IMPORTANT!: 40 It is necessary for all parts to be installed for t
Краткое содержание страницы № 19
Starting with nuts (16) flush against bracket (34), secure rim (42) and bracket to backboard. 18. Bend bracket (34) to line up with holes in backboard and secure. 19. IMPORTANT!: NOTE A: For spring loaded rim Mounting nuts and assembly, refer to bolts supplied with rim instructions included with hardware. rim hardware. 16 16 34 56 NOTE B: 42 Do not use washers here on spring return style rim. 19 12/03 P/N 211953C
Краткое содержание страницы № 20
Assemble upper elevator tubes (43) to backboard brackets (34). 20. 39 55 34 43 47 55 43 Support pole on sawhorse. Attach backboard WARNING! assembly to top pole section (4) as shown. 21. USE CAUTION; ELEVATOR Install pole cap (46). ASSEMBLY IS HEAVY. TWO PEOPLE REQUIRED FOR IMPORTANT!: THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING DO NOT OVER COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY TIGHTEN DAMAGE. 39 NOTE: STEP COMPLETED ASSEMBLY: 40 38 44 4 45 46 44 45 38 40 40 48 47 SAWHORSE OR SUPP
