Краткое содержание страницы № 1
English
Ashbury
Bath Ventilator with Light
Owner’s Manual
Model
81003
41937-01
1
20101026
©2010 Hunter Fan Co. 41937-01 10/26/2010
Краткое содержание страницы № 2
W A R N I N G TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in a manner intended by the manufacturer. Engineers (ASHRAE), and the local code authorities. If you have questions, contact the manufacturer. 5. When cutting or drilling into wall(s) or ceiling, do not damage 2. Before servicing or cleaning the unit, switch power off at ser- electrical wiring or other hidden utilities. vice panel and lock the service disconnecting m
Краткое содержание страницы № 3
95047-03-000 Check all the parts. E If damaged, call 77481-01-000 1-888-830-1326 F for replacements. 03242-07-133 G 95261-02-000 x4 A H 74508-03-133 x2 I B 77522-01 * J 3/8” Cable Connector 65219 K C * 96397-01-214 for model 81001 L 96397-02-444 for model 81003 75184-01-133 D x2 Extra Screws M NOTE: 86812-01-000 Strain relief cable * N connector must be installed. Not Included. 75733-01-214 for model 81001 O 75733-01-444 for model 81003 Included. Tools Needed. (Not supplied.) Estimated a
Краткое содержание страницы № 4
3 4 H E Remove the motor/blower from the housing. Remove packing material. 6 5 Remove the pre-loaded screw tip covers. Back out the pre-loaded screw tips until flush with the side of the housing. 7 8 F G Remove the wiring cover screw. Remove the wiring cover. 4 41937-01 10/26/2010
Краткое содержание страницы № 5
9 10 E C B Pop out the first wiring access slug. Use second if needed. Insert the strain relief (not included) into the housing and secure with washer. Choose Installation Option For New Construction - go to step A11, page 5 For Existing Construction - go to step B11, page 8 New Construction A12 A11 E 5/8 5/8 1/2 1/2 Position the correct depth mark at the bottom edge of the Screw pre-loaded screws into joist or framing. joist based on the thickness of your sheetrock. 5 41937-01 10/26/201
Краткое содержание страницы № 6
A13 Route wires through the strain relief. For supply connection, use wires suitable for at least 90º C (194º F). Ground A14 Black Green 2 Pin Bare Copper White A Black Main Switch 1 (AC In) Fan Motor White White 3 Pin Black Light Light *Option Black Switch 2 (AC In) *Option Fan & Main Light Together Connect wires as shown. A0 0 16 A15 E F G Install the wiring cover plate. Make sure all Connect 4” duct and vent to the outside. Tape joints. wiring connections are inside the box or under
Краткое содержание страницы № 7
ON OFF 0 0 0 0 0 0 0 0 A18 A17 0 0 0 0 0 0 0 0 H Connect wiring harness. DO NOT ALLOW THE MOTOR TO Reinstall the motor by inserting the tabs and pushing up HANG FROM THE WIRING HARNESS. into position. Make sure the wires are not pinched between the motor and the housing. A19 A20 I Secure the motor by tightening the 2 screws. Turn on the power source. A21 A22 Go to step C1 on page 10 to attach grille. Test the motor. If the motor does not run, check the plug connection. 7 41937-01 10/2
Краткое содержание страницы № 8
Existing Construction EXISTING FAN B11 B12 E Remove an existing fan and check to make sure the Move the housing into position above the ceiling. opening is large enough to accommodate the new motor housing (7 1/4”x 7 3/4”). B13 B14 Route wires through the strain relief. For supply connec- Attach existing ducting to duct connector. Tape joints. tion, use wires suitable for at least 90º C (194º F). If ducting does not fit securely, an adapter may need to be purchased. B15 E Install the housing
Краткое содержание страницы № 9
B16 Ground Black Green 2 Pin Bare Copper White A Black Main Switch 1 (AC In) Fan Motor White White 3 Pin Light Black Light *Option Black Switch 2 (AC In) *Option Fan & Main Light Together Connect wires as shown. B17 B18 F H G Install the wiring cover plate. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. B20 B19 I H Reinstall the motor by inserting the tabs and pushing Secure the motor by tightening the 2 screws. up into position. Make sure the wires are not
Краткое содержание страницы № 10
ON OFF B22 B21 Test the motor. If the motor does not run, Turn on the power source. check the plug connection. B23 Go to step C1 on page 10 to attach grille. Attaching the Grille C2 C1 L N M O Remove the thumbscrews. Remove glass dome. 10 41937-01 10/26/2010
Краткое содержание страницы № 11
C3 C4 K L Connect wiring harness. DO NOT ALLOW THE FIXTURE Remove the strain relief bracket screw. TO HANG FROM THE WIRING HARNESS. C5 C6 J Insert the strain relief bracket’s dog-leg tab so that Position the strain relief bracket under the it hooks over the lip of the motor. Reinstall the motor as shown. strain relief bracket screw. C8 C7 L L M Attach thumbscrews. Align posts 1, 2, and 3 (stamped into motor housing) with WARNING: To reduce the risk of electrical shock, posts 1, 2, and 3
Краткое содержание страницы № 12
C10 C9 N Align glass dome and push up. Install 2 Max 60 Watt A15 bulbs (Not Included). C11 O Screw glass dome into position. 12 41937-01 10/26/2010
Краткое содержание страницы № 13
Trouble Shooting Problem: Fan does not come on. Solution: • Hunter Fan Bath V entilators are extremely quiet. To confirm that the fan is running, place your hand near the vents to feel the air movement. • Turn power on, replace fuse, or reset breaker. • Check all plug connections to be sure they are secure. • Check the wiring to make sure it matches the wiring diagram. Problem: Light does not come on. Solution: • Replace the light bulb with a new bulb. • Turn power on, repl
Краткое содержание страницы № 14
Warranty Hunter Fan Company Bath Exhaust Fan LIMITED WARRANTY Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter bath exhaust fan: If any part of your Hunter bath exhaust fan (except for glass fixtures and light bulbs) fails at any time within one year after the date of sale to you due to a defect in material or workmanship, we will repair or, at our option, replace the defective part free of charge for parts and labor performed a
