Краткое содержание страницы № 1
50 - - 002 SERIES 1181281
50 - - 014 SERIES 1181280
FORD EXPEDITION
r
5. T -
FOR USE IN VEHICLES WITH FACTORY INSTALLED
OVERHEAD CONSOLE ONLY.
Apr. 14, 1999
INSTALLATION INSTRUCTION # 44 -
Printed in the U.S.A.
0018D
is installation: Materials provided for th
7. Audiovox Series 640/650 Video Module
6. 1/8" Drill Bit 10TORX bit driver
4. Razor knife or similar tool 3. Awl or scribe point tool or s
Краткое содержание страницы № 2
1 Nut, 6 - 32 HH KEPS 8 2 Screw, # 6 x 3/8 PPH TAB 13 3 Screw, # 8 x 9/16 PWH TAB 2 4 Screw, 6 - 32 x 1/2 PPH 4 5 Screw, 6 - 32 x 3/4 PPH 10 6 Screw, # 8 x 1 1/4 PWH TAB 2 7 Screw, # 8 x 1 1/2 PWH TAB 1 8 Screw, # 8 x 1 3/4 POH TAB Z1 2 9 4 10 2 11 Convoluted Tube, 1/2" ID X 3" 1 12 1 13 1 14 Pod Mounting Bracket 4 15 2 16 1 17 1 18 1 19 1 INSTALLATION INSTRUCTION # 44 - Apr. 14, 1999 . 2 Printed in the U.S.A 0018D Overhead Console Pl
Краткое содержание страницы № 3
3
Краткое содержание страницы № 4
I. REMOVAL OF O.E.M. EQUIPMENT. - f - d twist. using two (2) # 8 x 9/16" PWH screws (item 3 pg2). 4 Figure 3 Figure 2 See Figure 2 and 3. through modified louver opening and secure in place ided in kit 2. Install plywood block (item 18 pg 2) prov Figure 1 and remove indicated headliner. See Figure 1. A/C vent hole with arrow pointing forward. Cut 1. Place template provided (item 12 pg 2) over c
Краткое содержание страницы № 5
- # 8 x 1 1/4" PWH screw (it em 6 pg 2). See Fig. 4. tube (ite 5. Remove and retain two (2) OEM screws located 5 Figure 6 OEM screws. See Figure 6. front bracket (item 13 pg 2) using OEM holes and at front of OEM bracket near windshield. Mount Figure 5 chaffing against bracket. m 11 pg 2) around wire harness to prevent toward driver’s side of bracket. Install convoluted with OEM screws. See Figure 5. Ro
Краткое содержание страницы № 6
- - pillar to floor. Route power and ground leads forward to fuse box area. Connect power wire controlled power source per sensor extension, etc.) to VCP location. Connect per s ) screws. See Fig. 8. 6 Figure 9 removing eight ( 8 ) OEM screws. See Figure 9. 2. Remove and retain secondary light and pod assembly by Figure 8 assembly by removing four ( 4 1. Remove and retain OEM
Краткое содержание страницы № 7
3. Attach four (4 ) pod mounting brackets (item 14 pg 2) to front and rear of be - 32 X 1/2" screws (item 4 pg 2) and four (4) 8 - 32 KEPS X 3/8" PPH screws (item 2 pg 2) As shown. See Figure 11. 7 Figure 11 console (item 19 pg 2) with eight ( 8 ) # 6 4. Install and secure O.E. bezel in overhead Figure 10 nuts (item 1 pg 2). See Figure 10. zel with four (
Краткое содержание страницы № 8
Note: 8 Figure 13 accessible. Be sure light wiring is Figure13. overhead console with six ( 6 ) OEM screws. See 6. Install and secure secondary light pod assembly in Figure 12 See Figure 12. OEM screws in front assembly as shown. light and pod assembly, replace two ( 2 ) 5. Remove two (2) plastic tabs on secondary
Краткое содержание страницы № 9
(5) # 6 X 3/8" PPH screws (item 2 pg 2). See Figure 14. four ( 4 ) 6 - 32 X 3/4" screws (item 5 pg 2 ) and four (4) IV. INSTALLATION OF OVERHEAD CONSOLE. d to the vehicle. 9 Failure to do so may cause damage to console or installed components. Caution: Do not overtighten screws. Use extra support for the console until secure Figure 15 check for proper clearance and function. console openings. Manu
Краткое содержание страницы № 10
1. 2. using two (2) 6 - 32 X 3/4" screws bracket (Item 3). 3. Secure front of console using one ( 1 ) # 8 X 1 1/2" 4. - 10 Figure 19 Figure 17 in step 2. 32 X 3/4" screws previously installed 5. Tighten 6 front mounting bracket. See Fig. 17. pg 2) in dimple area at front of console through 1 1/4" PWH screw (item 6 Install one ( 1 ) # 6 x secondary pod and light assembly. See Figure 17. PWH screw (item 7) in front
Краткое содержание страницы № 11
with video system. your area. Note: Make sure that wires do not get pinched between bosses on video system and console. - pg 2). Caution: Do not overtighten screws. 18. Do not overtighten screws. 11 headliner. See Figure 19. o plywood support installed above dimples at rear of overhead console to secure rear of cons
Краткое содержание страницы № 12
12 CUT ON DOTTED LINES
