Краткое содержание страницы № 1
SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
HSU-18CK13(T3)
HSU-18HK13(T3)
Please read this operation manual before using the air conditioner.
No.0010557036
Краткое содержание страницы № 2
Cautions Disposal of the old air conditioner All these valuable materials may be taken to a waste collecting center and used again after adequate recycling. Before disposing an old air conditioner that goes out of use, please make sure it's Consult your local authorities for the name inoperative and safe. Unplug the air conditioner and address of the waste materials collecting in order to avoid the risk of child entrapment. centers and waste paper disposal services nearest to your house. It mus
Краткое содержание страницы № 3
Cautions For the purpose of the safety,the air con- Specifications ditioner must be properly grounded in acco- rdance with specifications. The refrigerating circuit is leak-proof. Remark per EMC Directive 89/336/EEC. Always remember to unplug the air To prevent flicker impression during the conditioner before openning inlet grill. Never start of the compressor(Technical Process) unplug your air conditioner by pulling on and the adversely influence caused by the power cord. Always
Краткое содержание страницы № 4
Cautions The machine is adaptive in following situation 1.Applicable ambient temperature range: 29oC/19oC Maximum: D.B / W.B Indoor Minimum: D.B / W.B 18oC/14oC Cooling Maximum: D.B 54oC/24oC Outdoor Minimum: D.B 18oC Maximum: D.B 27oC Indoor Minimum: D.B 15oC Heating Maximum: D.B / W.B 24oC/18oC Outdoor Minimum: D.B / W.B -7oC/-8oC 2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person. The type of connecting wire is H05RN-
Краткое содержание страницы № 5
Parts and Functions Indoor Unit Test running switch(manual) Used only for test running in cooling when room temp. is below 16oC. Inlet grille Don't use it in normal operation. Emergency switch(manual) Used when remote controller is lost or defective. Unit will run temporarily. Remote signal receiver Air filter A beeping sound is generated when a signal from remote controller is received. Vertical flap Power indicator Timer mode indicator Operation mode indicator Use remote controller to Lights u
Краткое содержание страницы № 6
Parts and Functions Buttons and display of the remote controller. 1.Mode display AUTO COOL DRY HEAT FAN LOW MED HI AUTO 2. SWING display 3. FAN SPEED display 4. HEALTH display 5. SLEEP display 6. LOCK display 7. TIMER ON display 8. AUXILIARY HEAT display 9. HEALTH 10. MODE Used to select AUTO,COOL and FAN 11. CLOCK Used to set correct time 12. TIMER Used to select TIMER ON,TIMER OFF 13. RESET Used to reset the controller back to normal condition. 14. CODE
Краткое содержание страницы № 7
Parts and Functions Buttons and display of the remote controller. If the unit which you purchased has not health function, remote controller should like the following figure: 1.Mode display AUTO COOL DRY HEAT FAN LOW MED HI AUTO 2. SWING display 3. FAN SPEED display 4. HEALTH display 5. SLEEP display 6. LOCK display 7. TIMER ON display 8. AUXILIARY HEAT display 9. SWING 10. MODE Used to select AUTO,COOL and FAN 11. CLOCK Used to set correct time 12. TIMER Used to s
Краткое содержание страницы № 8
Operation Remote controller's operation When in use, put the signal transmission head directly to the receiver hole on the indoor unit. The distance between the signal transmission head and the receiver hole should be within 7 m without any obstacle as well. Don't throw the controller, prevent it from being damaged. When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receivering
Краткое содержание страницы № 9
Operation Enjoy yourself by just a gentle press. Auto run, Fan operation (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display. (Not Timer setting) Power indicator on indoor unit lights up. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: AUTO COOL DRY HEAT FAN Unit will run in selected mode. Stop display at " " AUTO or " "FAN. (3) FAN Press FAN button. For each press, fan speed changes as follows:
Краткое содержание страницы № 10
Operation COOL,HEAT and DRY operation Recommendations: Use COOL in summer. Use HEAT in winter Use DRY in spring, autumn and in damp climate. (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display.(Not Timer setting) Power indicator on indoor unit lights up. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: AUTO COOL DRY HEAT FAN Unit will run in operation mode displayed on LCD. Stop display at your desired mode.
Краткое содержание страницы № 11
Operation (5) Air flow direction adjustment After operation mode is selected, vertical flap will open automatically according to the mode. Referring to the Fig. COOL HEAT About 60o About 10o Left and right air flow adjustment Up and down (Use remote controller) (manual) Press SWING button, vertical flap will move within Move the horizontal blade by a knob on air the range shown in the Fig. Press SWING button conditioner to adjust left and right direction stop it at a fixed position. referring to
Краткое содержание страницы № 12
Operation TIMER Operation Set Clock correctly before starting Timer operation You can let unit start or stop automatically at following times: Before you wake up in the morning, or get back from outside or after you fall asleep at night. TIMER ON/OFF (1)After unit start, select your desired operation mode. Operation mode will be displayed on LCD. Power indicator on indoor unit lights up. (2)TIMER mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display ch
Краткое содержание страницы № 13
Operation TIMER ON-OFF TIMER ON-OFF (1)After unit start, select your desired operation mode. Operation mode will be displayed on LCD. Power indicator on indoor unit lights up. (2) Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: blank ON OFF ON OFF TIMER ON TIMER OFF TIMER ON-OFF Select TIMER ON-OFF. "ON" will flash. (3)Time setting for TIMER ON Press HOUR button. Every time the button is pressed, time increases 10 min. If button is kept depr
Краткое содержание страницы № 14
Operation HEALTH Mode operation (1) Press the ON/OFF switch. (2) Press the "HEALTH" once," " is displayed, now the air conditioner is operating the health function. (3) Press the "HEALTH"again,then the health function stops. BRIEF INTRODUCTION TO HEALTH OPERATION The anion generator in the air conditioner can generate a lot of anion to effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally
Краткое содержание страницы № 15
Operation Emergency and Test Operation Emergency operation: Use this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed,the" Pi "sound is heard once, which means the start of this operation. In this operation, it is possible to change the settings of temperature and air flow speed, it is Pi also impossible to do an operation by the timer. Follow the requirements below. Room Timer Designated Air flow Operation temperature mode temp
Краткое содержание страницы № 16
Operation Comfortable SLEEP Before going to bed at night, you can simply press the SLEEP button and unit will bring you a sound sleep in selected mode. In COOL mode One hour after SLEEP mode starts, temp. will become 1oC higher than temp. setting. After running for another 1 hour, temp. rises by 1oC further. Unit will run for 6 hours then stops automatically. Temp. is higher than temp. setting so that room temp. won't be too Iow for your sleep.(As shown in Fig.l) In HEAT mode One hour after SLEE
Краткое содержание страницы № 17
Maintenance Different models have different appearance Cleaning of unit casing Cut off power supply before cleaning unit casing with soft cloth. In case of heavy stain, clean it with neutral detergent. squeeze water in the cloth, wipe off the detergent on unit casing completely. Cleaning of remote controller Don't use water to wash unit casing, please use dry cloth. Don't use glass cleaner or cloth soaked with chemicals. Cleaning of air filter Air Filter 1.Open inlet grille by pulling it upward.
Краткое содержание страницы № 18
Maintenance Better use of air conditioner Proper room temperature. Cleaning of the air filter. Once every two weeks Proper temperature Effective use of the timer. Closing of doors and windows during operation Curtains or blinds for windows Avoid time-wasteful operation Never fail to observe the followings Do not sprinkle water over Do not block the inlet or outlet. the unit. Do not pull power plug. Do not use for other purposes. Such as food preservation plant cultivation or animal breeding. 17
Краткое содержание страницы № 19
Trouble shooting Before asking for service, check the following first. Phenomenon Cause or check points The system does not restart When unit is stopped, it won't restart immediately. immediately until 3 minutes have elapsed to protect the system. When the electric plug is pulled out and reinserted, the protection circuit will work for 3 minutes to protect the air conditioner. During unit operation or at stop, a swishing or gurgling noise may be heard. At first 2-3 minutes after unit start, this
