Руководство по эксплуатации Metra Electronics 99-8714

Краткое содержание страницы № 1

INSTALLATION INSTRUCTIONS FOR PART 99-8714
APPLICATIONS
SMART FORTWO
2008
99-8714
KIT FEATURES
• DIN Radio Provision with Pocket
• Stacked DIN Units Provision
KIT COMPONENTS
A) Radio Housing • B) Pocket
A B
TOOLS REQUIRED:
• Small Flat Blade Screwdriver/ Panel Removal Tool
• T-20 Torx Screwdriver
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2008 METRA ELECTRONICS CORPORATION

Краткое содержание страницы № 2

99-8714 TABLE OF CONTENTS Dash Disassembly - Smart Fortwo 2008 .... ... .... ... .... ... .... ... .... ...1 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - Stacked DIN Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 *Note: Refer also to the instructions included with the aftermarket radio.

Краткое содержание страницы № 3

99-8714 DASH DISASSEMBLY SMART FORTWO 2008 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip the Hazard button switch panel. (Figure A) 3 Remove (1) T-20 Torx head screw. (Figure B) 4 Carefully unclip the panel surrounding the radio, start at the top of the dash and work your way down. (Figure C) B 5 Remove (4) T-20 Torx head screws from around the radio. (Figure D) 6 Disconnect the wire harness and antenna and remove radio. Continue to kit assembly.

Краткое содержание страницы № 4

99-8714 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the radio housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) 3 Snap the pocket into the radio hous- ing. (Figure C) Continue to final assembly. B NOTE: Pocket may be installed in top or bottom of radio housing. C 2

Краткое содержание страницы № 5

99-8714 KIT ASSEMBLY STACKED DIN UNITS PROVISION Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cages into the radio housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket units into the cage until it snaps into place. (Figure B) Continue to final assembly. B 3

Краткое содержание страницы № 6

99-8714 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas

Краткое содержание страницы № 7

99-8714 NOTES 5

Краткое содержание страницы № 8

99-8714 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 03/27/08 © COPYRIGHT 2008 METRA ELECTRONICS CORPORATION INST99-8714