Руководство по эксплуатации Metra Electronics 99-9224

Краткое содержание страницы № 1

INSTALLATION INSTRUCTIONS FOR PART 99-9224
APPLICATIONS
1999-2006 Volvo S80
99-9224
KIT FEATURES
• DIN Head Unit Provision with Pocket
KIT COMPONENTS
( A) Radio Housing
A
TOOLS REQUIRED:
Phillips Screwdriver • T-25 Torx Driver
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION

Краткое содержание страницы № 2

99-9224 TABLE OF CONTENTS Dash Disassembly 1999-2006 Volvo S80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1,2 Kit Assembly DIN Head Unit Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Краткое содержание страницы № 3

DASH DISASSEMBLY 99-9224 1999-2006 VOLVO S80 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unsnap gear shifter trim panel. (Figure A) 3 Unsnap gear shifter boot to separate it from the gear shifter trim panel and remove trim panel. (Figure B) B Remove (2) T-25 Torx head screws 4 from bottom of climate controls. (Figure C) 5 Unsnap the climate controls from bottom edge of the radio. Unplug and remove the climate controls. (Figure D) C D 12 VOLT AUTO 72 7

Краткое содержание страницы № 4

DASH DISASSEMBLY 99-9224 1999-2006 VOLVO S80 E 6 Remove (2) T-25 Torx head screws from bottom of radio. Unplug and remove the radio. (Figure E) 7 Depress the snaps on the top and bottom of the pocket to remove it from the radio bracket. (Figure F) 8 Remove (5) T-25 Torx head screws securing the radio to the radio bracket and slide the bracket off of F the radio. (See Figure G) Note: Save the radio bracket for use with radio housing. (Figure H) TOP SNAP H G TORX HEAD 2

Краткое содержание страницы № 5

KIT ASSEMBLY 99-9224 DIN HEAD UNIT PROVISION A NOTE: Also refer to the instructions included with the aftermarket radio. 1 Using a Phillips screw driver remove the rear support bracket from the radio housing. (Figure A) 2 Snap the radio housing into the radio bracket (removed from factory radio) and replace rear support bracket. (Figure B) B 3 Slide the DIN cage into the radio housing and secure by bending the metal locking tabs outward. (Figure C) 4 Slide the radio into the cage/ radio housing

Краткое содержание страницы № 6

FINAL ASSEMBLY 99-9224 FINAL ASSEMBLY Locate the factory wiring harness in the dash and make the connection as shown. 1 Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. 2 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring

Краткое содержание страницы № 7

99-9224 NOTES 5

Краткое содержание страницы № 8

INST999224 1-800-221-0932 www.metraonline.com REV. 03/15/06 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST99-9224