Руководство по эксплуатации Metra Electronics 99-7875T

Краткое содержание страницы № 1

INSTALLATION INSTRUCTIONS FOR PART 99-7875/99-7875T
APPLICATIONS
Honda Accord 2008-2010
(For Non-Navigation models with Dual Zone Climate controls)
Honda Accord Crosstour 2010
99-7875/99-7875T
KIT FEATURES
• Painted To Match Factory Dash
99-7875=Charcoal, 99-7875T=Taupe
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets

Краткое содержание страницы № 2

Краткое содержание страницы № 3

99-7875/99-7875T DASH DISASSEMBLY HONDA ACCORD 2008-10 / CROSSTOUR 2010 1 Disconnect the negative battery ter- A minal to prevent an accidental short circuit. 2 Unclip and remove the trim panel from above the glove box at the right side of the factory radio. (Figure A) 3 Unclip and remove the trim panel at the left side of the factory radio. (Figure B) B 4 Remove the (2) Phillips screws from the left and right side of the of the factory radio. (Figure C) 5 Unclip and remove the top of the cen- t

Краткое содержание страницы № 4

99-7875/99-7875T DASH DISASSEMBLY HONDA ACCORD 2008-10 / CROSSTOUR 2010 9 Remove (2) Phillips screws facing up F on the bottom of the factory radio. (Figure H) 10 Unclip the factory radio assembly. Unplug and remove the radio assem- bly. (Figure I) 11 Remove (6) Phillips screws securing the climate controls to the factory radio assembly and remove the con- trols from the assembly. (Retain the G screws and climate controls for re- use during kit preparation.) 12 Remove (4) Phillips screws securin

Краткое содержание страницы № 5

PASSENGER AIRBAG 99-7875/99-7875T KIT PREPARATION HONDA ACCORD 2008-10 / CROSSTOUR 2010 Snap the hazard switch/passenger air A 1 bag light assembly into the radio housing from front. (Figure A) 2 Secure the a/c vents into the radio housing using the factory hardware from rear. (Figure B) 3 Secure the climate controls into the radio housing using the factory hard- ware from rear. (Figure C) B 4 Secure the trim panel onto the radio housing using the factory hardware. (Figure D) 5 Attach the c

Краткое содержание страницы № 6

99-7875/99-7875T KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the DIN cage until it snaps into place. (Figure B) 3 Snap the pocket into the radio housing. (Figure C) Continue to final assembly. B C 4

Краткое содержание страницы № 7

99-7875/7875T KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Mount the ISO Brackets to the radio A using the screws supplied with the radio. (Figure A) 2 Slide the radio into the Radio Housing until it snaps into place. (Figure B) 3 Snap the Trim Plate onto the front of the Radio Housing. (Figure C) 4 Snap the Pocket into the Radio Housing. (Figure C) B Continue to final assembly. C 5

Краткое содержание страницы № 8

99-7875/99-7875T KIT ASSEMBLY DOUBLE DIN/STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Cut and remove the center bar from A the Radio Housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the Radio Housing. (Figure B) 3 Slide the Double DIN or stacked ISO mount units into the bracket/radio housing assembly and secure the unit(s) to the assembly using the screws supplied with the unit(s). (Figure C) B 4 Snap the

Краткое содержание страницы № 9

99-7875/99-7875T FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order o

Краткое содержание страницы № 10

99-7875/7875T NOTES 8

Краткое содержание страницы № 11

99-7875/99-7875T NOTES 9

Краткое содержание страницы № 12

99-7875/7875T INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 04/21/10 © COPYRIGHT 2008-2010 METRA ELECTRONICS CORPORATION INST99-7875