Руководство по эксплуатации Metra Electronics 99-2006G

Краткое содержание страницы № 1

INSTALLATION INSTRUCTIONS FOR PART 99-2006
APPLICATIONS
Cadillac CTS 2003-2007
Cadillac SRX 2004-2006
99-2006/
99-2006G
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked DIN Head Units Provision
• Painted To Match Factory Dash
99-2006 = BLACK
99-2006G = GRAY
KIT COMPONENTS
A) Radio Housing • B) DDIN Brackets • C) DDIN Trim Plate • D) ISO Brackets • E) Trim Plate • F) (8) Phillips screws
• (G) Pocket
E
D
C
B

Краткое содержание страницы № 2

99-2006 TABLE OF CONTENTS Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2, 3, 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com

Краткое содержание страницы № 3

DASH DISASSEMBLY 99-2006 CADILLAC CTS 2003-2007 CADILLAC SRX 2004-2006 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 11:39 PM 2 Unclip and remove the center air vent assembly above the radio. (Figure A) 60 60 3 Open ashtray and remove (1) Phillips head screw from inside ashtray. B 4 Unclip and remove the a/c control/ ashtray assembly below the radio. 11:39 PM (Figure B) Rear View Remove (4) 10 MM screws securing 5 the radio to the dash. (Figure C, D) 60 60

Краткое содержание страницы № 4

99-2006 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 2 Slide the aftermarket head unit into the cage and secure. (Figure B) Slide the supplied pocket into the 3 B unused opening. ISO MOUNT RADIO PROVISION WITH POCKET A 1 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A) 2 Slide the head unit into the radio opening until the side clips engage. (Figu

Краткое содержание страницы № 5

99-2006 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION A 1 Remove the center bar from the 99- 2006 radio housing. (Figure A) 2 Attach the corresponding bracket to the DDIN head unit. (Figure B) Insert the DDIN trim plate into the 3 radio housing. (Figure C) B Position the bracket/radio assembly 4 to the back of the radio housing and secure with the (8) Phillips screws provided. (Figure D) C D Rear View 3

Краткое содержание страницы № 6

99-2006 KIT ASSEMBLY STACKED DIN HEAD UNITS PROVISION A Slide the DIN cages into the Radio 1 Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket head units into the cages and secure. (Figure B) B 4

Краткое содержание страницы № 7

99-2006 KIT ASSEMBLY FINAL ASSEMBLY Locate the factory wiring harness in the dash and make the connection as shown. 1 Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. 2 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring co

Краткое содержание страницы № 8

INST992006 1-800-221-0932 www.metraonline.com Rev. 08-08-08 © COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION INST99-2006