Руководство по эксплуатации Kenwood KDC-C712

Краткое содержание страницы № 1

KDC-C712
KDC-C662
KDC-C462
COMPACT DISC AUTO CHANGER
INSTRUCTION MANUAL
© B64-1381-00 (EF)

Краткое содержание страницы № 2

Safety precautions 2WARNING • The disc name preset feature can store the Take the following precautions to prevent fire names of up to 50 discs in memory. This and avoid personal injury : feature may sometimes unable to be • Check that no metal objects (coins, tools, controlled from the control unit. etc.) are left inside the unit to avoid short Do Not Use Special Shape CDs circuits. • Be sure to use round shape CDs only for this • If you smell or see smoke, turn the power off unit an

Краткое содержание страницы № 3

Handling compact discs Stains, scratches, or warping can cause skipping, malfunction, or low sound quality. Take the following precautions to avoid damage to the compact discs. • Avoid touching the recorded side (the side without the titles on) when you hold a compact disc. • Do not stick paper tape, etc. on either stick of the disc. • Do not store discs where they will be exposed to direct sunlight (such as on the seat and dashboard) or high heat. • If you do not use your unit for an extende

Краткое содержание страницы № 4

' ' O - N ' Loading compact discs Projection Tray 1 3 2 "EJECT" 45 6 1. Make sure the disc magazine is the right way 3. Open the CD changer door. up with the "disc" logo on the top.Pull the tray 4. Insert the magazine into the CD changer until out by the projection. it clicks. 2. Place the disc on the tray with the label facing 5. Close the CD changer door. upwards. Insert the tray into the disc NOTE magazine until it locks. Check that the discs Use the CD changer with its door closed to and tr

Краткое содержание страницы № 5

O - N Connections Changer control terminal Control unit (optional) "O" "N" D Changer control cable (5m) 2CAUTION • Do not connect the changer control cable while the control unit is turned ON. • Be sure to press the reset button after installation. • Do not install an antenna of radio equipment or distribute the antenna cable near the changer output cable, for this could cause malfunction with this unit. n Setting the O-N switch Set the O-N switch (lying to the right of the EJECT key) dependi

Краткое содержание страницы № 6

Installation n Accessories A · 1 B · 4 C · 4 D · 1 E · 1 F · 1 n Installation Procedure 1 Removing the transportation screws Remove all 3 transportation screws for protecting the internal mechanism before you start to install the unit. Transportation screws NOTE After removing the transport screw, retain it carefully and attach it again before transporting the unit again. 2 Angle adjustment switches • The angle adjustment switches on the both side of the unit are to be set according to 3 Cover t

Краткое содержание страницы № 7

0 45 90 Installation n Horizontal installation C KDC-C662/C462 KDC-C712 0 45 3 A 0 45 90 90 3 3 0 45 90 3 0 45 90 3 B 3 ø4 3 3 0 45 90 3 Bottom view n Vertical installation KDC-C662/C462 KDC-C712 C 0 45 0 45 90 3 90 3 3 0 45 A 90 0 45 3 3 90 3 B 0 3 3 45 90 ø4 3 Bottom view n In case of hanging in the trunk ø4 KDC-C662/C462 KDC-C712 0 45 3 0 45 90 90 3 3 A 0 45 B 90 3 0 45 90 3 3 C 3 3 0 45 90 3 Bottom view 7 0 45 90 0 45 90

Краткое содержание страницы № 8

Troubleshooting Guide PROBLEM POSSIBLE CAUSE SOLUTION Sound skips due to vibration. • The unit is mounted at a slant. • Mount the unit so that is level. • Changer unit is mounted in an • Mount the unit in a stable place. unstable place. • The angle adjustment switches are • Set the angle adjustment switches to set improperly. the correct positions. The disc changer mode cannot The O-N selection switch of the disc Set the O-N selection switch to "O" be selected. changer is not set properly. posit