Краткое содержание страницы № 1
0010555512
Краткое содержание страницы № 2
Краткое содержание страницы № 3
Краткое содержание страницы № 4
Краткое содержание страницы № 5
1 1 2 4 4 5 5 6-7 8-12 8 8-12 13-20 14 14 15-20 21-22 22-23 24
Краткое содержание страницы № 6
Important: Test power plug before each use: 1. Press ìreset ìbutton. 2 . Press ìtest ìbutton, unit should trip. 3. Press ìresetî button again for use . Do not use if above test fail. In the event this device trips , the cause of the malfunction is to be corrected before further use of the device .
Краткое содержание страницы № 7
Краткое содержание страницы № 8
vent controller side vent louvers electronic touch pad easy-access filters You can run the fan only on not so hot days. The fan can be set to run at 3 speeds (HIGH fan, MED fan, LOW fan)as desired by you. You have 3 levels of Fan Speed to set at your desired comfort level. HIGH, MED and LOW. 24
Краткое содержание страницы № 9
12. Electrostatic Filter (not all models) Being constructed of high efficiency purifying The Fresh Air Vent allows the air conditioner to recirculate inside air , draw fresh air into the room substance, active carbon fabric, electrostatic fabric, and exhaust stale air to the outside . electrostatic active carbon net and other materials it purifies the air effectively. Its wavy structure increases the capability to filter dust and smoke effectively . Due to the retention of the active carbon it h
Краткое содержание страницы № 10
Remote control and control panel operations
Краткое содержание страницы № 11
Having set the temperature you will set the function of the air conditioner. Every time you press the MODE button, it will change between FAN, COOL, ENERGY SAVER and DEHUM. (See Fig. # 3)
Краткое содержание страницы № 12
Once the function mode is decided you will have to set the fan speed.(See fig. #4) Every time you press the SPEED button, fan speed will change between LOW, HIGH,MED. 1) If you choose the COOL mode you can run the fan in one of the 3 speeds HIGH, MED, LOW. 2) For cool days you may want to run the "FAN" function. The fan can be set to run at 3 speeds (HIGH fan, MED fan, LOW fan)as desired by you. 4)Energy Saver : The unit runs the same as COOL setting in the ENERGY SAVER mode. But the fan will be
Краткое содержание страницы № 13
Краткое содержание страницы № 14
Fig. # 5 Adjusting the Air Flow Direction Airflow can be adjusted by changing the direction of the air conditioner's louvers. This can also increase the cooling efficiency of the air conditioner. Adjusting Vertical Air Flow Direction Adjusting Horizontal Air Flow Adjusting the Horizontal vane up and down will Direction change vertical airflow. The vane can be adjusted Adjusting the vertical louvers left and by nudging the back or up and down of the vane. right will change horizontal airflow. Ad
Краткое содержание страницы № 15
Краткое содержание страницы № 16
Parts Par ts Supplied window seal top r ail gasket wood screws 31/32" 2 1/2 "long flat 19/32" long scre w and head bolt and basepan angle loc kn ut loc kn ut curtain attachment left and r ight installation bracket Remote curtains screws 13/32" (left and r ight) control side Model: HWR18VC5, HWR24VC5, ESA3156,ESAX3186, ESA3245,ESA3185 ìCR2025ì battery
Краткое содержание страницы № 17
Installing Unit into A Window Window Opening Requirements The air conditioner is designed to fit into double or single hung sash type windows. Each of the units comes with an installation kit that provides adjustable mounting louvers, to fill the gaps between the sides of the unit, and the window frame. The chart below reflects the dimensions of the units with, and without installation kits. Measure your window opening width and compare it to the chart below to ensure that it meets the minimum
Краткое содержание страницы № 18
ASSEMBLE 2 CURTAINS/TOP RAIL Inst all top rail with four 13/32" screws. Slide lef t-hand cur t ain assembly into lef tend of top and bottom rails. Repeat for right-hand cur t ain assembly .Fasten cur tain ret ainer strip s to sides of outer case with six13/32" screws. Storm window installation Mobile home window installation PREPARE If storm window frame does not allow Add wood strip (at least 1 1/2" wide) 3 WINDOW FOR adequate clearance below sill (1/2 " along entire wid th of window sill. requ
Краткое содержание страницы № 19
4 W L T op rail About 5∞ Bottom rail t yl a ia : T .yti lc rof ya 2/1 the bracket on the case. them to proper length ,then use 4 (19/32")screws to fix bolt and locknut) to the installation bracket and adjust and as shown in fig . Install bolt(2 " long flat head windows sash. Install left & right installation bracket Use two wood screws 31/32" to fix the case to through clearance hole in curt ains. drive, drill a pilot hole into sash aw ar o NO TEmake screws easier to Cu rt n sse mb cu screws.
Краткое содержание страницы № 20
LLA 5 F . : t . futS . . 6 Caution: F or security purpose, reinstall screws at cabinet's sides , removed in step one. ef ficiency indoor sash. This will stop air leakage which reduces seal strip between out door window glass and top of Cut window seal gasket to wid th of window f window function of the window Also st ay clear of glass. Be careful not to damage the Add a piece of ape to the drill bit as a depth gauge. Important Be careful not to drill pilot hole too deep. frames, drill a pilot ho
