Краткое содержание страницы № 1
EVPK9 Linear Extractor
Manual for Installation, Use and Maintenance
Passionate about style
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
Краткое содержание страницы № 2
Important The manufacturer cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that the manufacturer reserves the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment. This appliance is not designed to be used by people (including children) with reduced physical, sensorial or mental capacity, or who lack experience or knowle
Краткое содержание страницы № 3
Using your Extractor For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for approximately 15 minutes after the end of cooking. Control Panel A - Light key B - Decrease speed key C - Display D - Increase speed key E - Timer key Fig. 1 B A C D E To switch the extractor light on and off • Touch key A. To switch on the extractor • Touch either key B or D. The appliance will switch on at the first speed. • To increase the speed
Краткое содержание страницы № 4
Care and Maintenance IMPORTANT : DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. Cleaning You should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. You can clean your extractor effectively by simply using a dilute solution of water Fig. 2 and mild detergent and drying to a shine with a clean cloth. Cleaning the grease filter The grease filters
Краткое содержание страницы № 5
Changing the Light DO NOT CHANGE THE LIGHT BULB IMMEDIATELY AFTER USE AS THE BULB WILL BE HOT. ALLOW IT TO COOL BEFORE REMOVING IT. Using a flat blade screwdriver, carefully prise off the lamp cover as shown in figure 5. Remove the bulb and replace with a 12V 20W halogen light bulb. Finally, replace C the light bulb cover. D Do not touch bulbs or adjacent areas during or straight after prolonged use of Fig. 5 the lights. The light is designed for use during cooking and not for general roo
Краткое содержание страницы № 6
Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSED SPUR OUTLET AND PROTECTED BY A 3A FUSE. We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E. and local regulations. DOUBLE POLE SWITCHED The wires in the mains lead of this appliance are coloured in accordance with the FUSED SPUR OUTLET following
Краткое содержание страницы № 7
Electrical Information Mains electrical voltage: 230 – 240Vac, 50Hz Total rated power consumption: 290W Troubleshooting If your extractor is not working: 1. Check that the mains supply has not been switched off. 2. Check that the fuse in the spur has not blown. 6
Краткое содержание страницы № 8
Mounting your Extractor IMPORTANT: The extractor is intended to be mounted directly to the ceiling using fixings appropriate for the ceiling. Ensure that there is adequate ceiling strength and supports at the fixing points; if in doubt, consult a joiner or electrician. 318 When the extractor is to be installed above an electric hob, the minimum distance between the hob and extractor must exceed 600mm (650mm is recommended). 57 When the extractor is to be installed above a gas hob, the min
Краткое содержание страницы № 9
Installation Your extractor can be used to filter and recycle the air within your kitchen (A), or to extract the air outside (B). When extracting air to the outside, the unit can be vented as shown in the diagram below. Fig. 4 To mount your extractor to the ceiling 1. Firstly, remove the lower section of the support frame, by removing the screws shown in Fig 4 below, and then carefully sliding the two sections apart. 2. Using the supplied template, mark the positions of the 3 mai
Краткое содержание страницы № 10
Installation 4. Insert 3 screws into the main fixings, leaving approximately 3mm protruding, as shown in Fig 7 5. Fit the upper support section (B) into position on the 3 screws and rotate it into position, as shown in Fig 7. 6. When in position, tighten the 3 main screws and fit an Fig. 7 additional screw (X) to fix the support frame section in position. 7. Measure the height of the ceiling and then the hotplate height from the floor. The length of the support sections sho
Краткое содержание страницы № 11
Installation 9. Assemble the ventilation duct(H), as shown in the diagrams below dependant on whether you are extracting air to the outside (Fig 10) or re-circulating (Fig 11), in which case you will need to use the supplied T-piece (M). Ensure that the duct adapter (F) is securely connected to the duct pipe or T-piece in order to minimise noise. 10. Fit the vent adapter(F) to the body of the motor as shown in Fig 11 using 2 screws (E) 11. Mount the upper chimney section o
Краткое содержание страницы № 12
Installation 11. Mount the upper chimney section onto the frame section and secure in position using the 2 screws (A) as in Fig 13. 12. Carefully slide the lower section over the upper section and tape it in position (L) near the shortest position. 13. Fit 2 screws into the holes on the body of the hood (O), leaving approximately 3mm protruding. 14. Mount the main motor body to the screws (O) through the keyed slots, as shown in Fig 14 and secure the Fig. 13 body in position us
Краткое содержание страницы № 13
12
Краткое содержание страницы № 14
13
Краткое содержание страницы № 15
14
Краткое содержание страницы № 16
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
