Краткое содержание страницы № 1
INSTRUCTION
MANUAL
MODEL HVC MODEL HVC-282 -282
MODEL HVC MODEL HVC MODEL HVC-282 -282 -282
V V V V VA A A A ACUUM CONTROLLER CUUM CONTROLLER CUUM CONTROLLER CUUM CONTROLLER CUUM CONTROLLER
Краткое содержание страницы № 2
Manual Print History Manual Print History Manual Print History Manual Print History Manual Print History The print history shown below lists the printing dates of all revisions and addenda created for this manual. The revision level letter increases alphabetically as the manual undergoes subsequent updates. Addenda, which are released between revisions, contain important change information that the user should incorporate immediately into the manual. Addenda are numbered sequentially. When a new
Краткое содержание страницы № 3
TABLE OF CONTENTS SECTION 1.0 GENERAL INFORMATION........................................................................................... 5 1.1 Descripion......................................................................................................................... 5 1.2 Operating Principle ..................................................................................................................................... 5 1.3 Specifications .................................
Краткое содержание страницы № 4
PAGE 4
Краткое содержание страницы № 5
1.0 GENERAL INFORMATION This manual contains technical and general information concerning the installation, operation and calibration of the Hastings HVC-282 V acuum Gauge, and associated components. For proper operation, the Hastings HVC-282 V acuum Gauge must be suitably connected to a Hastings Model DV-273 Gauge Tube. Attempting to use this V acuum Gauge with any other transducer may damage the gauge and or transducer. 1.1 Description: The HVC-282 vacuum instrument offers a digital readou
Краткое содержание страницы № 6
Hi / Lo Relays............................................................................... SPDT N.O./N.C. up to 125VAC 10A or 277VAC 6A With onetime ≈10sec. delay to prevent relay chater, only during unit power up. 0 O Operational Limits ....................................................................................... 0 to 50 C <80%RH non-condensating. 0 0 Storage: -20 to 50 C (Non-operational). Size .....................................................................................
Краткое содержание страницы № 7
2.0 GAUGE TUBE AND CABLES 2.1 Gauge Tubes: Octal sockets of standard metal tubes are color-coded for easy identification; DV-273 is dark blue. The tubes are to be installed in 1/8" NPT female thread, or in a Hastings type OS Quick Connector. Maximum overpressure of gauge tube is 150 psi. Construction of shell is of Nickel-plated steel. See section 1.2 for Operating Principle. 2.2 Gauge Tube Cables: The four color-coded wires (Black, Red, White, Green) are connected as shown on the label on th
Краткое содержание страницы № 8
3.0 INSTALLATION 3.1 Panel Mounting: Section 8 of this manual shows an outline drawing detailing panel cutout for a standard Hastings CVT Gauge. Install the meter on the panel using the supplied hardware. 3.2 Gauge Tube Installation: Situate the gauge tube in a clean, dry vacuum system with the open end pointing down so as to be self-draining should any vapors condense in it (see Section 6.0). Screw metal tubes into 1/8" female NPT threads using a suitable sealant; T eflon tape is recommend
Краткое содержание страницы № 9
4.0 OPERATION 1) Plug in power cable into any single or two phase AC line for 115VAC or 220VAC 50/60Hz operation, per unit configuration. T o change input voltage configuration, remove all connecting wires to rear terminal strips, then removing two small screws at rear, remove can. On lower PC board push slide switch toward rear of can for 115VAC, and toward front of can for 220V AC, reassemble in opposite order. Remark can as to new voltage configuration. A 3-wire grounded power cord is su
Краткое содержание страницы № 10
5.0 CALIBRATION AND TROUBLESHOOTING GUIDE All Hastings V acuum Gauges and Gauge Tubes have been carefully checked and calibrated at the factory before shipment. If a calibration check is desired, the methods in the following sections may prove helpful. 5.1 Checking of Tube: The simplest and quickest method of checking operation and calibration of a gauge tube is to keep a new spare clean gauge tube on hand as a “standard”. T o check operation, install both new and old gauge tubes together in
Краткое содержание страницы № 11
f) Adjust outside pot to read 2.630mV ±5µ V on DVM. g) DV-273 gauge tube is now calibrated. HVC-282 calibration. Course adjustment (Caution: Resistor connections are not to any power terminals.) a) With power off, connect an 86.6 ohm 1% 1/8W resistor to tube terminals white & green. b) Connect a 28 ohm 1% 1/8W resistor to tube terminals red and black. c) Connect a DVM to measure mV across the 28 ohm resistor with (+) lead to red terminal. d) With power on, adjust trim pot on right side of
Краткое содержание страницы № 12
6.0 NOTES ON VACUUM MEASUREMENT 6.1 Effects of Condensable Vapors: If the readings of Hastings Vacuum Gauges are to be compared with readings of other types of gauges, consideration must be given to the possible effects of condensable vapors in the system on the other gauges. For example, none of the many types of the McLeod Gauge give correct readings if condensable vapors such as water, alcohol, acetone, etc., are present in the system/gauge. The McLeod Gauge operates by compressing residu
Краткое содержание страницы № 13
7.0 SERVICE INFORMATION 7.1 Warranty Repair Policy Hastings Instruments warrants this product for a period of one year from the date of shipment to be free from defects in material and workmanship. This warranty does not apply to defects or failures resulting from unauthorized modification, misuse or mishandling of the product. This warranty does not apply to batteries or other expendable parts, nor to damage caused by leaking batteries or any similar occurrence. This warranty does not appl
Краткое содержание страницы № 14
PAGE 14
Краткое содержание страницы № 15
7.3 Service Form: Teledyne Hastings Instruments RMA# 804 Newcombe Avenue (contact factory) Hampton, VA 23669 U.S.A. Telephone (757)723-6531 Fax (757)723-3925 Model No. Serial No. P.O. No. Date Name Phone Company Address City State Zip Describe problem: Show a block diagram of your system including unit inlet and outlet pressures: Calibration range Gas Cable length Power line voltage Variation Ambient temperature Gas Temperature Other (If special modifications have been made by user, please de
Краткое содержание страницы № 16
PAGE 16
Краткое содержание страницы № 17
8.0 DRAWINGS and DIAGRAMS This section contains the schematics, parts list, and overall assembly drawings. If replacement parts are desired, they can be obtained from the factory by referencing the Hastings part number listed on the parts lists. PAGE 17
Краткое содержание страницы № 18
PAGE 18
Краткое содержание страницы № 19
PAGE 19
Краткое содержание страницы № 20
PAGE 20
