Краткое содержание страницы № 1
INSTALLATION
FT8332/FR8332
Fiber Transmitter
and Receiver
Thirty-Two Digitally Encoded
Video Channels
C2652M (1/08)
Краткое содержание страницы № 2
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Product Overview . . . . . . . . . . . . . . . . . .
Краткое содержание страницы № 3
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the pola
Краткое содержание страницы № 4
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provid
Краткое содержание страницы № 5
Product Overview DESCRIPTION The FT8332 transmitter and FR8332 receiver provide the ability to transmit up to 32 composite video channels over one optical fiber (refer to Figure 1). FT8332 FR8332 TRANSMITTER RECEIVER ONE FIBER 32 VIDEO INPUTS 32 VIDEO OUTPUTS Figure 1. Thirty-Two Channel Video FT8332 Transmitter and FR8332 Receiver Features of the FT8332/FR8332 fiber optic transmission system include the following: � 8-bit digitally encoded video for high-quality multichannel video transmis
Краткое содержание страницы № 6
FRONT PANEL The front panel of the FT8332/FR8332 unit provides a removable bezel. Figure 2 illustrates the front of the unit with the bezel attached. Figure 3 illustrates the front of the unit with the bezel removed. NOTE: The Contact Closure Activation and Data Activity LEDs shown in Figure 3 are not used. Figure 2. Front Panel of FT8332/FR8332 Unit with Bezel Figure 3. Front Panel of FT8332/FR8332 Unit Without Bezel ì Power LED: Lights the Pelco badge blue to indicate that power is being ap
Краткое содержание страницы № 7
REAR PANEL Figure 4 illustrates the rear panel of the FT8332/FR8332 unit. Figure 4. Rear Panel of FT8332 Transmitter/FR8332 Receiver ì Video Connectors 1-32: BNC connectors that provide 75-ohm analog video input (FT8332)/output (FR8332). î Fiber Optic Connector: An ST multimode or single-mode connector. ï Auxiliary Relay Output Connector: A 3-pin header that provides a relay output to external equipment if an optical signal or laser fault occurs. ñ Stand-Alone Power Connector: A 5-mm barrel
Краткое содержание страницы № 8
Installation PACKAGE CONTENTS The following items are supplied: 1 FT8332 transmitter or FR8332 receiver 1 Accessory pack: 1 Screw terminal, 3-pin (for relay) 1 Regulated switching power supply, 90-264 VAC, 47-63 Hz input, 12 VDC (66 W) output 3 Power cords (North American, U.K., and European) 2 Front bezel keys 1 Rack mount kit (included with accessory pack): 2 Chassis mounting brackets with thumbscrews 6 Screws, 6-32 x 0.25-inch, Phillips flat head (three for each bracket) 2 Adjustable support
Краткое содержание страницы № 9
ACCESSORY PACK FRONT BEZEL KEY 2 EA. RACK MOUNT KIT USA ST TANDARD EUROPEAN UK POWER SUPPLY 3-PIN SCREW POWER CORD STANDARD POWER STANDARD POWER TERMINAL 1 EA. (110 VAC) CORD (250 VAC) CORD (220 VAC) 1 EA. 1 EA. 1 EA. 1 EA. Figure 6. Accessory Pack REAR MOUNT RAIL 2 EA. RACK MOUNT KIT FRONT MOUNT RAIL CHASSIS MOUNTING 2 EA. BRACKETS SHOWN ACTUAL SIZE PHILLIPS FLAT PHILLIPS TRUSS PHILLIPS FLAT PHILLIPS PAN CAGE NUT, HEAD SCREW, HEAD SCREW, HEAD SCREW, HEAD SCREW, 10-32 6-32 X 0.25-INCH 8-32 X
Краткое содержание страницы № 10
MOUNTING THE TRANSMITTER/RECEIVER The FT8332 transmitter/FR8332 receiver can be mounted into a rack (refer to Mounting the Transmitter/Receiver into a Rack) or can be used as a stand-alone unit. As a stand-alone unit, the transmitter/receiver can be placed on a desktop or can be mounted to a wall (refer to Mounting the Transmitter/Receiver to a Wall on page 13). MOUNTING THE TRANSMITTER/RECEIVER INTO A RACK The FT8332 transmitter/FR8332 receiver can mount into an industry-standard 19-inch (48
Краткое содержание страницы № 11
2. Mount one front-mount support rail with one rear-mount support rail back-to-back, and attach the rails using three 8-32 x 0.375-inch Phillips truss head screws (refer to Figure 9). Leave the screws loose until the support rails are attached to the rack in step 7. (3) SCREWS, 8-32 X 0.375 PHILLIPS TRUSS HEAD Figure 9. Assembling a Support Rail 3. Repeat step 2 for the other set of front-mount and rear-mount support rails. 4. If you are installing the unit into a square-hold rack, continue wi
Краткое содержание страницы № 12
d. Position the ear of the rear-mount rail against the rear exterior of the equipment rack, and align the top and bottom holes in the ear of the rail with the threaded holes (or cage nuts) in the equipment rack. e. Using two 10-32 x 0.5-inch Phillips pan head screws, attach the ear of the rail to the rear of the rack. Insert the screws from the outside of the rack, pointing toward the front of the rack (refer to Figure 11). RACK FRONT RACK REAR (2) SCREWS, (2) SCREWS, 10-32 X 0.5-INCH 10-32 X
Краткое содержание страницы № 13
9. After the unit is in place, tighten the two thumbscrews to secure the unit to the rack (refer to Figure 13). THUMBSCREW Figure 13. Tightening the Thumbscrews MOUNTING THE TRANSMITTER/RECEIVER TO A WALL The FT8332 transmitter/FR8332 receiver can be mounted to a wall using the WM5300 wall mount kit. The WM5300 wall mount kit provides three slots, allowing a maximum of three FT8332/FR8332 units to be mounted to a wall. For detailed information, refer to the WM5300 Wall Mount Kit Installation
Краткое содержание страницы № 14
CONNECTIONS Connections to the FT8332 transmitter/FR8332 receiver are made on the rear panel of the unit (refer to Figure 14). FIBER OPTIC CABLE RELAY WIRING (REFER TO TABLE A) POWER CONNECTION COAXIAL CABLES, COAXIAL CABLES, COAXIAL CABLES, COAXIAL CABLES, FOR EPS5000-120 CHANNELS 25-32 CHANNELS 1-8 CHANNELS 9-16 CHANNELS 17-24 POWER SUPPLY POWER CONNECTION FOR STAND-ALONE UNIT Figure 14. FT8332 Transmitter/FR8332 Receiver Connections As illustrated in Figure 14, connections to the tra
Краткое содержание страницы № 15
Troubleshooting LED indicators on the front of the FT8332 transmitter/FR8332 receiver allow you to monitor operating power, video signal status, optical signal status, and laser status. To view the indicators on the front of the transmitter/receiver, remove the bezel from the unit (refer to Removing the Bezel). To troubleshoot the front-panel indicators, refer to Troubleshooting Front-Panel Indicators. REMOVING THE BEZEL To remove the bezel from the front of the transmitter/receiver, do the fo
Краткое содержание страницы № 16
Table B. Troubleshooting Front-Panel Indicators (Continued) Indicator Color Meaning Possible Cause Corrective Action TX Optical Link Loss Flashing red Laser has shut down. Transmitter is operating in extreme Ensure that transmitter operates environmental conditions; for example, according to recommended operating operating temperature is below or conditions, and then cycle the power. above recommended range (refer to If problem persists, contact Specifications on page 17). Product Support a
Краткое содержание страницы № 17
Specifications VIDEO Number of Channels 32 Modulation Type Pulse code modulation, 8-bit resolution Video Input (FT8332)/ Video Output (FR8332) 1.0 Vp-p, 75 ohms; NTSC, PAL, and SECAM Bandwidth 6.5 MHz Gain Unity Crosstalk -50 dB typical at 3.58 MHz Differential Gain <1% Differential Phase <1.2° Tilt <1% Signal-to-Noise Ratio >60 dB (CCIR weighted) RELAY Relay Output 1 A at 30 VDC Choice of normally open or normally closed GENERAL Operating Temperature -40° to 167°F (-40° to 75°C) Input Power Re
Краткое содержание страницы № 18
OPTICAL POWER BUDGET AND TRANSMISSION DISTANCE Model Number Optical Maximum Compatible Power Transmission Transmitter Receiver Wavelength Budget Distance Multimode (62.5/125 µm) † ‡ FT8332MSTR FR8332MSTR 1350 nm 18 dB* 1 km (0.6 mi) 1325 nm 1300 nm 1275 nm Single-Mode (9/125 µm) § FT8332SSTR FR8332SSTR 1350 nm 18 dB* 26 km (16.1 mi) 1325 nm 1300 nm 1275 nm *Optical power budget is 15 dB when operating temperature range is -40° to 0°C. † When using 50/125 µm multimode fiber, subtract 3 dB from t
Краткое содержание страницы № 19
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in Pelco assumes no risk and shall be subject to no liability for damages or loss material or workmanship for a period of one year after the date of shipment. resulting from the specific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of Exceptions to this warranty are as noted below
Краткое содержание страницы № 20
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO9001 Australia Canada Finland France Germany Italy Macau The Netherlands Russia Singapore | | | | | | | | | South Africa Spain Sweden United Arab Emirates United Kingdom United States | | | | |
