Краткое содержание страницы № 1
1013460
4-POINT SUB-FRAME MOUNTING KIT
for Backhoe Models
BH70-X, BH80-X, BH6500, BH7500
®
on New Holland Tractors
T2220, TC29DA, TC33DA, TC34DA FWA
®
or Case IH Tractor
®
Farmall 31, Farmall 35, DX34 FWA
with Woods LS84, LC96, LC102
1009, 1012 Loaders
New Holland 14LA Loader
or Case IH L340 Loader
Includes Hose Kit
1013484
Tested. Proven. Unbeatable.
SAVE THIS
MANUAL!
Include it with the
backhoe manual. It
contains safety,
operation, and repair
part information not
found in other
manual
Краткое содержание страницы № 2
TO THE DEALER: ® Assembly and proper installation of this product is the responsibility of the Woods dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Product Registration online at the Woods Dealer Website or complete the mail-in form included with the Operator’s Manual. If using the mail-in form, the dealer is to
Краткое содержание страницы № 3
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Make sure that all operating and service person- ! nel know that if hydraulic fluid penetrates skin, it LEA EL INSTRUCTIVO! must be surgically removed as soon as possible by Si no lee Ingles, pida ayuda a a doctor familiar with this form of injury or gan- alguien que si lo lea para que le grene, serious injury, or death will result. CON- traduzca las medidas de seguridad. TACT A PHYSICIAN IMMEDIATELY IF FLUID ENTERS SKIN OR EYES. D
Краткое содержание страницы № 4
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) Do not allow bystanders in the area when oper- ating, attaching, removing, assembling, or servic- Make sure all hydraulic hoses, fittings, and ing equipment. valves are in good condition and not leaking before Before operating, make sure stabilizer pads are starting power unit or using equipment. Check and lowered firmly to the ground. Stabilizer arms pro- route hoses carefully to preven
Краткое содержание страницы № 5
BACKHOE SUB-FRAME INSTALLATION Tractor Preparation ■ Only use 1013460 4-Point Sub-Frame Mount- ing Kit for mounting Woods BH70-X, BH80-X, ® BH6500, BH7500 backhoe on New Holland T2220, TC29DA, TC33DA, TC34DA tractors or ® ® Case IH DX34, Farmall 31, Farmall 35 tractors equipped with Woods LS84, LC96, LC102, 1009 and 1012 loaders, New Holland 14LA loader or Case IH L340 loader. Any other use or modifica- tion of this mounting kit may result in serious DP11 injury or death. Figure 1. Re
Краткое содержание страницы № 6
Install Front Mounts With Woods LS84 Loader Mount Attach front mount (32) to the right loader mount using two cap screws (26), hardened flat washers (23) and hex nuts (27). 23. 57817 5/8 Hardened flat washer 26. 902 5/8 NC x 2 HHCS GR5 27. 230 5/8 NC Hex nut 32. 1026846 Front mount (LS84 only) Figure 4. Front Mount Installation With New Holland 14LA Loader Mount or Woods LC96, LC102, 1009, 1012 Loader Mount NOTE: Front mounts can be installed over the loader 19 mount or loader mount and mid-mo
Краткое содержание страницы № 7
Install Tractor Brackets With Woods LS84 Loader Mount 4. Place right tractor bracket (1) under right side of tractor. Use a hydraulic floor jack to help raise 1. Place left tractor bracket (2) under left side of and hold tractor bracket in position. tractor. Use a hydraulic floor jack to help raise and hold tractor bracket in position. 5. Attach right tractor bracket (1) to front mount (32) using two cap screws (26), hardened flat washers 2. Attach left tractor bracket (2) to left loader mou
Краткое содержание страницы № 8
Install Tractor Brackets 1. Place left tractor bracket (2) under left side of tractor. Use a hydraulic floor jack to help raise and hold tractor bracket in position. 2. Attach left tractor bracket to left front mount (8) using two cap screws (26), hardened flat washers (23), and hex nut (27). NOTE: Tractors equipped with mid-mount mower, place tractor bracket on the inside of front mount as shown in Figure 9. Tractors without mid-mount mower, place on the outside of front mount. 3. Attach tr
Краткое содержание страницы № 9
Install Cross Brace 1. Remove PTO shield. 7. 1013474 Cross brace 2. Attach cross brace (7) to rear of tractor using two 15. 1093 1/2 NC Hex nut cap screws (24) and hardened flat washers (23). 18. 24576 1/2 NC x 1-3/4 Cap screw GR5 3. Attach to right and left tractor brackets using four 22. 57816 1/2 HArdened flat washer (two per side) cap screws (18), hardened flat 23. 57817 5/8 Hardened flat washer washers (22), and hex nuts (15). 24. 64062 M16 x 2.0P x 40 mm Cap screw 4. Install PTO shield
Краткое содержание страницы № 10
Torque Mounting Hardware TORQUE SPECIFICATIONS Wrench Ref Cap Screw Qty Size Required Torque 16 1/2 NC x 6 4 1/2" 85 lbs-ft (115 N-m) 18 1/2 NC x 1-3/4 4 1/2" 85 lbs-ft (115 N-m) 19 M16 x 2.0P x 70 mm 4 24 mm 125 lbs-ft (169 N-m) 20 M16 x 2.0P x 55 mm 4 24 mm 125 lbs-ft (169 N-m) 24 M16 x 2.0P x 40 mm 2 24 mm 125 lbs-ft (169 N-m) 26 5/8 NC x 2 8 15/16" 170 lbs-ft (230 N-m) 28 5/8 NC x 3 4 15/16" 170 lbs-ft (230 N-m) Attach Backhoe Mounts to Backhoe NOTE: Leave all hardware loose until backhoe h
Краткое содержание страницы № 11
HYDRAULIC INSTALLATION Keep hands and body away from pressurized Make sure all hydraulic hoses, fittings, and lines. Use paper or cardboard, not hands or other valves are in good condition and not leaking body parts to check for leaks. Wear safety gog- before starting power unit or using equipment. gles. Hydraulic fluid under pressure can easily Check and route hoses carefully to prevent dam- penetrate skin and will cause serious injury or age. Hoses must not be twisted, bent
Краткое содержание страницы № 12
Install Hydraulic Block and Fittings 1. Locate the hydraulic manifold block on the right 7. 2472 5/16 Lock washer side of the tractor just under the fender (Figure 8. 307130 M8 x 1.25P x 40 mm Cap screw 19) and remove the block-off cap. 9. 307134 M8 x 1.25P x 100 mm Cap screw 2. Attach hydraulic block (18) to tractor using new o- 11. 313049 Elbow, 9/16 ORBM x 9/16 JICM rings (14), three cap screws (8) and one cap 14. 62726 O-ring .487 x .103 screw (9) plus washers (7). Make sure o-rings are 15
Краткое содержание страницы № 13
Install Bulkhead Adapter on Backhoe Mount 1. Attach bulkhead adapter (1) to crossmember between backhoe brackets. Secure with nut sup- plied with adapter. 2. Attach elbow (10) and female quick coupler (16) to bulkhead adapter as shown in Figure 23. 3. Position elbow and quick coupler to point upward. 1. 1006144 Adapter, Bulkhead 3/8 NPTM x 3/4 JICM 10. 313017 Elbow, 3/8 NPTM x 3/8 NPTF 90° 16. 64299 Quick coupler, female Figure 23. Bulkhead Adapter Installation - Backhoe Install Hoses to Bac
Краткое содержание страницы № 14
Mount Backhoe to Tractor Check Hydraulic System Check all hydraulic fittings and lines to be sure they are tight and free of kinks or twists. Mount Backhoe This mounting kit is designed to provide 1. Remove the backhoe seat assembly. secure mounting and adequate operator clear- ance for most operators when properly installed. 2. Back tractor up to backhoe and center mount Check clearance dimensions shown below to be between the tractor rear tires. Position tractor so sure you have inst
Краткое содержание страницы № 15
Mount Backhoe to Tractor (Continued) 10. Install cap screws (12) and slotted hex nuts (13). Refer to Figure 26. Tighten with 1-1/2 inch open end wrench provided 5. Using the backhoe hydraulics position the back- with kit. Return wrench to storage position (see hoe brackets at a slight angle, approximately 5 to Figure 26). 10 degrees. 11. Secure hex nut into position with klik pin (14). 6. Raise backhoe up by lowering stabilizers and 12. Shut off tractor and remove key. boom section until b
Краткое содержание страницы № 16
Remove Backhoe from Tractor 7. Use the boom to relieve excess pressure on 1 inch bolts and remove bolts. 8. Tilt backhoe main frame to separate slots on the The only time the backhoe may be operated backhoe brackets from the tractor brackets. from a position other than the operator seat is 9. Raise stabilizers until backhoe brackets slide out during backhoe attachment and removal. Opera- of hooks on the bottom of the tractor brackets. tor must: � Read Mounting Kit Manual instructions
Краткое содержание страницы № 17
STORAGE Connect Hydraulic Hoses TRACTOR: Connect male quick coupler on end of hose to female quick coupler at bulkhead bracket when backhoe is removed from tractor. See Figure 28. NOTICE ■ Failure to connect hoses together will result in damage to tractor hydraulic system. DP14 Figure 28. Hose Connection - Backhoe Removed BACKHOE: Connect IN and OUT quick couplers together to prevent dirt and debris from accumulating in quick couplers. See Figure 29. DP15 Figure 29. Backhoe Hose Connection,
Краткое содержание страницы № 18
1013460 4-POINT SUB-FRAME MOUNTING KIT 31 - PN 1006885 WARNING PINCH POINT Keep hands clear. 1006885 Serial Number Plate MODEL NO. SERIAL NO. Woods Equipment Company Oregon, Illinois, U.S.A. REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 1013462 1 Right tractor bracket 18 24576 * 4 1/2 NC x 1-3/4 HHCS GR5 2 1013463 1 Left tractor bracket 19 307430 4 M16 x 2.0P x 70 mm HHCS 3 1013464 1 Right backhoe bracket 20 307429 4 M16 x 2.0P x 55 mm HHCS 4 1013465 1 Left backhoe bracket 21 57798 6 3/4
Краткое содержание страницы № 19
1013484 HOSE KIT REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 1006144 1 Adapter, bulkhead 11 313049 1 Elbow, 9/16 ORBM x 9/16 JICM 45° 3/8 NPTM x 3/4 JICM 12 360215 1 Hose, 14" x 9/16 JICF x 9/16 JICF 2 1009493 1 Hose, 40" x 3/8 NPTM x 9/16 JICF 13 38604 1 Elbow, 9/16 JICM x 9/16 JICF 90° 3 1009495 1 Adapter, bulkhead 14 62726 4 O-ring .487 x .103 3/8 NPTM x 9/16 JICM 15 63558 1 Elbow, 9/16 JICM x 9/16 ORBM 4 1010924 1 Hose, 40" x 3/8 NPTM x 3/4 ORBM 16 64299 2 Quick coupler, female 5 101
Краткое содержание страницы № 20
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. All torque values are given to specifications used on hardware define
